Hubbardton Forge 18667 User Manual

Assembly & Installation Instructions A283

Brindille Single Pendant 18-667 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products
and options.

To Complete Fixture Assembly (Figures 1 & 2)

Component Parts

A Fixture Pipe
B Canopy
C Crossbar
D Ground Screw
E Threaded Stud (2)

Caution: Be sure power is off at the main breaker box prior to installation.

1. Thread the wires from the fixture pipe (A) into and through the canopy pipe (G) up

through the canopy (B).

2. Unscrew the clutch (I) from the canopy pipe (G); slide it across the wires and onto

the fixture pipe (A). Follow this with the plastic clutch sleeve (H), oriented so the
tapered end of the clutch sleeve nests in the clutch.

3. Slide the canopy pipe (G) as far as necessary to give you the total length of the

fixture which you desire. Be careful not to scratch the pipe surfaces and to pull
excess wire up through the canopy pipe (G). Screw clutch (I) onto canopy pipe (G).
There must be a minimum 1-1/2" of inner pipe inside the outer pipe. Hand-tighten the
clutch to temporarily hold this adjustment. The clutch is not securely fastened at this
point; do not depend on it to hold the fixture.

strength, be sure the tapered end of the plastic clutch sleeve is oriented toward the
clutch when assembled and securely tighten set screw (Figure 2)

4. Thread studs (E) through appropriate holes in crossbar (C) to match holes in

canopy (B).

5. Using two machine screws (not provided), fasten the crossbar (C) to the electric box.

Note: A new electric box comes with screws. When replacing a fixture, retain the
existing screws for use with the new fixture

6. Using suitable wire connectors (not provided) connect fixture wires to supply (white

to white or ribbed and black to black or smooth). Run a pigrail lead from crossbar
ground screw (D) to the junction box and connect all ground
wires (bare copper or green to bare copper or green).

Make sure wire connectors are twisted on securely, and no bare
wire is exposed

.

7. Slide canopy (B) over threaded studs (E) and push firmly to

ceiling, making sure that no wires are pinched between fixture
canopy and ceiling. Fasten with knurled balls (F). Be sure studs
are fully seated in the knurled balls.

F Knurled Ball (2)
G Canopy Pipe
H Plastic Clutch Sleeve
I Clutch
J Set Screw

Important: To ensure full connection

.

Caution:

.

(Figure 1)

(Figure 2)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

26721

Assembly & Installation Instructions A283

Brindille Single Pendant 18-667 Page 2 of 2

8. Once the fixture is fastened to the ceiling, tighten the set screw (J) in clutch (I) firmly with hex wrench provided.

Only after the set screw (J) is tight should you install the glass.

9. Refer instructions following to install glass.

To Install Glass

Component Parts

K Barrel Knobs (3)
L Bulb (Included)
M Bulb Shield
N Glass
O Socket
P Spider

1. Remove barrel knobs (K) from spider (P) and set them aside.

2. Install light bulb (L). Be careful not to touch bulb with bare hands; oil

from the hands will dramatically reduce bulb life.

3. Thread bulb shield (M) over socket.

4. Raise glass (N) and align holes with spider (P). Fasten glass (N) to spider

(P) using barrel knobs (K).

5. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture

Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

(Figure 3)

(Figure 3)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

26721