CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Stem Assembly (Figure 1)
Component Parts
A Fixture Pipe
B Fixture Coupling
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipe (A), threaded end first, over fixture wires.
3. Apply a drop of the supplied thread locking compound to the internal threads
of the fixture coupling (B) and screw stem into fixture, being careful not to
twist the wires.
Note: Application of the thread locking compound is necessary to prevent
the stem from loosening during regular maintenance and cleaning of the
fixture. Be certain to apply the compound.
4. See instructions below to complete the installation.
Prepare the Canopy
Component Parts
C Jam Nut (2)
D Crossbar
E Threaded Nipple
F Canopy
G Canopy Ring
H Coupling
I Canopy Pipe
(Figure 2)
Caution: Be sure power is off at the main breaker box prior to installation.
1. Thread Jam Nut (C) and Crossbar (D) onto threaded nipple (E) leave both
parts loose.
2. Using two machine screws (not provided), temporarily fasten the crossbar
(D) to the electric box.
Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.
3. Adjust the length of Threaded Nipple (E) in crossbar (D) so that Canopy
Ring (G) will hold Canopy (F) against the ceiling with no threads showing
for best appearance. When the correct adjustment is established, tighten
Jam Nut (C) against crossbar (D) to hold the adjustment.
4. Remove the crossbar and stem from the electrical box and proceed with the
A Fixture Pipe
C Jam Nut
D Crossbar
E Threaded Nipple
F Canopy
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Thread crossbar (D) onto threaded nipple (E) until tight against
jam nut (C).
2. Unscrew the clutch (K) from the canopy pipe (I); slide it across the
wires and onto the fixture pipe (A). Follow this with the plastic clutch
sleeve (J), oriented so the tapered end of the clutch sleeve nests in the
clutch (Figure 3).
3. Thread wires from the fixture pipe (A) through the canopy pipe (I).
4. Slide the canopy pipe (I) as far as necessary to give you the total
length of the fixture which you desire. Be careful not to scratch the
pipe surfaces and to pull excess wire up through the canopy pipe (I).
There must be a minimum 1-1/2" of inner pipe inside the outer pipe.
Screw clutch (K) onto canopy pipe and hand-tighten the clutch to
temporarily hold this adjustment. The clutch is not securely fastened
at this point; do not depend on it to hold the fixture.
Important: To ensure full connection strength, be sure the tapered
end of the plastic clutch sleeve is oriented toward the clutch when
assembled and securely tighten set screw (Figure 4).
5. Using two machine screws (not provided), fasten the crossbar to the
electric box.
Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.
6. Using suitable wire connectors (not provided), connect fixture wires
to supply wires (white to white or ribbed side of the fixture cord,
black to black or smooth side, and bare copper to bare copper or
green supply). Push wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.
7. Slide fixture canopy (F) against ceiling, and secure with canopy
ring (G).
8. Refer instructions below and install glass.
G Canopy Ring
I Canopy Pipe
J Plastic Clutch Sleeve
K Clutch
L Set Screw
M Glass
N Socket
O Bulb (Included)
U Retaining Ring
1.Remove retaining ring (U) from socket (N). Retaining Rings are shipped
installed.
2. Slip glass (M) over socket (N).
3. Thread retaining ring (U) onto socket. Do not over tighten.
4. Install light bulb (O) and restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.