Page 1
Assembly & Installation Instructions A281
(Figure 1)
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 2)
Adjustable Mobius Shade Pendant 18-455 Page 1 of 7
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Stem Assembly (Figure 1)
Component Parts
A Fixture Pipe
B Fixture Coupling
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipe (A), threaded end first, over fixture wires.
3. Apply a drop of the supplied thread locking compound to the internal threads
of the fixture coupling (B) and screw stem into fixture, being careful not to
twist the wires.
Note: Application of the thread locking compound is necessary to prevent the
stem from loosening during regular maintenance and cleaning of the fixture.
Be certain to apply the compound.
4. See instructions below to complete the installation.
Prepare the Canopy (Figure 2)
Component Parts
C Jam Nut
D Crossbar
E Threaded Nipple
F Canopy
G Canopy Ring
Caution: Be sure power is off at the main breaker box prior to installation.
1. Thread jam nut (C) and crossbar (D) onto threaded nipple (E); leave both parts
loose.
2. Using two machine screws (not provided), temporarily fasten the cro ssba r (D) to
the electric box.
fixture, retain the existing screws for use with the new fixture.
Note: A new electric box comes with screws. When replacing a
3. Adjust the length of threaded nipple (E) in crossb a r (D) so that canopy ring (G)
will hold canopy (F) against the ceiling with no threads showing for best
appearance. When the correct adjustment is established, tighten jam nut (C)
against crossbar (D) to hold the adjustment.
4. Remove the crossbar and stem from the electrical box and proceed with the
assembly instructions.
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26650
Page 2
Assembly & Installation Instructions A281
(Figure 3)
(Figure 4)
Adjustable Mobius Shade Pendant 18-455 Page 2 of 7
Complete Assembly & Install Fixture (Figures 3 & 4)
Component Parts
A Fixture Pipe
F Canopy
G Canopy Ring
H Cano p y Pipe
I Plastic Clutch Sleeve
J Clutch
K Set Screw
L Ground Screw
Caution: Be sure power is off at the main breaker box prior to installation.
1. Place canopy (F) over canopy pipe (H), followed by canopy ring (G). Make
sure smaller diameter side of canopy ring is oriented up toward the canopy.
2. Thread wires from the fixture pipe (A) through the canopy pipe (H).
3. Unscrew the clutch (J) from the canopy pipe (H); slide it across the wires and
onto the fixture pipe (A). Follow this with the plasti c clutch sleeve (I), oriented
so the tapered end of the clutch sleeve nests in the clutch. (Figure 3).
4. Slide the canopy pipe (H) as far as necessary to give you the total length of the
fixture which you desire. Be careful not to scratch the pipe surfaces and to pull
excess wire up through the canopy pipe (H). There must be a minimum 1-1/2"
of inner pipe inside the outer pipe. Hand-tighten the clutch to temporarily hold
this adjustment. The clutch is not securely fastened at this po in t; do not depend
on it to hold the fixture.
Important: To ensure full connection strength, be sure the tapered end of the
plastic clutch sleeve is oriented toward the clutch when assembled and
securely tighten set screw (Figure 3).
5. Carefully slide canopy ring (G) and canopy (F) down over fixture pipe (A)
until they rest on the fixture.
6. Using two machine screws (not provided), fasten the crossbar to the electric
box.
Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.
7. Using suitable wire connectors (not provided), connect fixture wires to supply
wires (white to white supply, black to black supply). Run a pigtail lead from
crossbar ground screw (L) to the junction box and connect all ground wires
(bare copper or green to bare copper or green). Push wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and no bare wire
is exposed.
8. Slide fixture canopy (F) against ceiling, and secure with canopy ring (G).
9. Once the fixture is fastened to the ceiling, tighten the set screw (K) firmly with
hex wrench provided.
10. Refer to instructions below to install shade and light bulb.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
(continued)
26650
Page 3
Assembly & Installation Instructions A281
(O) Female End
(M) Flat Shade Panel (2)
(N) Male End Plastic
Buttons (8)
Adjustable Mobius Shade Pendant 18-455 Page 3 of 7
To see a video on how to assemble the Mobius shade go to:
http://www.youtube.com/watch?v=EQzAHb_Ab2M
To Assemble Shade
Component Parts
M F lat Shade Pa nel (2)
N Male End Plastic Button (8)
O Female End Plastic Button (8)
Plastic Buttons (8)
Step 1 Identify all parts needed.
Step 2 Fold shade panel (M) over and
align letter designations “L”.
Note: Top letter "L" should be
oriented the same as the bottom
letter "L".
Step 3 Slip male end of plastic button
down through bottom of shade
panel as shown.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
(continued)
26650
Page 4
Assembly & Installation Instructions A281
Adjustable Mobius Shade Pendant 18-455 Page 4 of 7
Step 4 Align "L" holes and mount the
other side of the shade panel
(M) onto the two male end
plastic buttons (N). Install two
female end plastic buttons (O)
and press firmly to snap into
place. Clip excess length of the
male button off after installing
female plastic buttons.
Step 5 Repeat steps 2-4 for other flat
shade panel (M).
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26650
Page 5
Assembly & Installation Instructions A281
Adjustable Mobius Shade Pendant 18-455 Page 5 of 7
Step 6 Slip male end plastic buttons
(N) through the “C” side of
the shade panel (M).
Letter “C” should read the
same as shown).
holes and mount the other side
of the shade panel (M) onto
the two male end plastic
buttons (N).
Step 7 Install two female end plastic
buttons (O) and press firmly
to snap into place. Clip excess
length of the male button off
after installing female plastic
buttons.
Step 8 Fold the shade panel (M) as
shown to match the “C” sides.
Insert the other side of the
shade panel (M) onto the two
male end plastic buttons (N).
Note:
Align "C"
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26650
Page 6
Assembly & Installation Instructions A281
Adjustable Mobius Shade Pendant 18-455 Page 6 of 7
Step 9 Install two female end plast ic
buttons (O) and press firmly
to snap into place. Clip excess
length of the male button off
after installing female plastic
buttons.
Bottom View of Assembled Shade
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26650
Page 7
Assembly & Installation Instructions A281
(Figure5)
Adjustable Mobius Shade Pendant 18-455 Page 7 of 7
Install Shade & Bulb (Figure 5)
Component Parts
P Socket
Q Shade Assembly
R Washer
S Retaining Ring
1. Slip shade assembly (Q) followed by washer
(R) over socket (P).
2. Thread retaining ring (S) onto socket (P) and
tighten until snug.
3. Install light bulb. (Not Included)
4. Restore electricity at the main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26650
Loading...