Hubbardton Forge 18264 User Manual

Assembly & Installation Instructions A291

(Figure 1)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

(Figure 1)

For Trumpet Pendant 18-263, 18-264 Page 1 of 2

Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products and
options.

To Complete Fixture Assembly (Figure1)

Component Parts

A Crossbar
B Ground Screw
C Threaded Studs (2)
D Canopy
E Knurled Balls (2)

Caution: Be sure power is off at the main breaker box prior to installation.

1. Thread the wires from the fixture pipe (J) into and through the canopy pipe (F)

up through the canopy (D).

2. Unscrew the clutch body (H) from the fixture pipe (J); slide it across the wires

and onto the canopy pipe (F). Follow this with the plastic clutch sleeve (I),
oriented so the tapered end of the clutch sleeve nests in the clutch.

3. Slide the canopy pipe (F) as far as necessary to give you the total length of the

fixture which you desire. Be careful not to scratch the pipe surfaces and to pull
excess wire up through the canopy pipe (F). Screw clutch body (H) onto fixture
pipe (J). There must be a minimum 1-1/2" of inner pipe inside the outer pipe.
Hand-tighten the clutch to temporarily hold this adjustment. The clutch is not
securely fastened at this point; do not depend on it to hold the fixture.

Important: To ensure full connection strength, be sure the tapered end of the
plastic clutch sleeve is oriented toward the clutch when assembled and securely
tighten set screw.

4. Thread studs (C) through appropriate holes in crossbar (A) to match holes in

canopy (D).

5. Using two machine screws (not provided), fasten the crossbar (A) to the electric

box. Note: A new electric box comes with screws. When replacing a fixture, retain

the existing screws for use with the new fixture.

6. Using suitable wire connectors (not provided) connect fixture wires to supply

(white to white or ribbed and black to black or smooth). Run a pigtail lead
from crossbar ground screw (B) to the junction box and connect all ground
wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.

7. Slide canopy (D) over threaded studs (C) and push firmly to ceiling, making sure that no wires are pinched between

fixture canopy and ceiling. Fasten with knurled balls (E). Be sure studs are fully seated in the knurled balls.

8. Once the fixture is fastened to the ceiling, tighten the set screw (G) in clutch body (H) firmly with hex wrench

provided. Only after the set screw (G) is tight should you install the glass.

9. Refer to instructions below to install glass

F Canopy Pipe
G Set Screw
H Clutch Body
I Clutch Sleeve
J Fixture Pipe

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735 26922

(continued)

Assembly & Installation Instructions A291

(Figure 4)

(Figure 2)

(Figure 3)

For Trumpet Pendant 18-263, 18-264 Page 2 of 2

To Install Opaque Glass (Figure 2)

Component Parts

K Socket
L Glass
M Retaining Ring

1. Remove retaining ring (M) from socket (K). Retaining Ring is shipped installed.

2. Place glass (L) over socket (K).

3. Replace retaining ring (K) and tighten until snug against glass (L). Do not over-tighten.

4. Install light bulb. Not included

5. Restore electricity at the main breaker.

To Install Water Glass (Figures 3 & 4)

Component Parts

K Socket
L Glass
N Socket Cover
M Retaining Ring
O Decorative Ring Cover

1. Remove retaining ring (M) from socket (K). Retaining Ring is shipped installed.

2. Install retaining ring (M) into decorative ring cover (O). If retaining ring (M) fits to loose

bend a few inside tabs of the decorative ring cover (O) (Figure 3).

3. Place glass (L) over socket (K).

4. Install socket cover (N) replace retaining ring (M) and tighten until snug against glass (L).

Do not over-tighten.

5. Install light bulb. Not included

6. Restore electricity at the main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer
from which you purchased this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735 26922