Hubbardton Forge 144710 User Manual

Installation Instructions A205

For Antasia Pendant 14-4710, 14-4710E, 14-4715 & 14-4715E Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install the Canopy (Figure 1)

Component Parts

A Ground Screw
B Crossbar
C Lock Nut
D Nipple

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the crossbar (B) to the electric

box (see illustration).

Note: A new electric box comes with screws. When replacing a fixture, retain
the existing screws for use with the new fixture.

3. Thread the nipple (D) into the crossbar (B) and secure with lock nut (C); slide

canopy (E) over nipple (D), and attach the canopy loop (F) to the nipple (D).
Adjust the nipple to proper length to ensure a snug canopy fit before proceeding.

4. Attach one end of the chain to the fixture loop (H). Lace the wire through every

other link of the chain to the end. Slip wires and chain through the collars and
canopy (G, F & E). Fasten the chain to the canopy loop (F), slip wires through
the loop and nipple into the electric box. Make sure to provide enough slack in
the wire to ensure weight of fixture is supported by the chain.

5. Using suitable wire connectors (not provided) connect fixture wires to supply

wires (white to ribbed side of the fixture s cord, black to smooth side). Connect
all ground wires to crossbar ground screw (A).

Caution: Make sure wire connectors are twisted on securely, and no bare wire
is exposed.

6. Raise canopy (E) to the ceiling and secure loop collar (G) to canopy loop (F).

E Canopy
F Canopy Loop
G Loop Collar
H Fixture Loop

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22762

Installation Instructions A205

For Antasia Pendant 14-4710, 14-4710E, 14-4715 & 14-4715E Page 2 of 2

To Install Inner Glass

Component Parts

I Socket
J Inner Glass
K Retaining Ring

(Figure 2)

1. Remove retaining ring (K) from socket (I). Retaining Rings are shipped installed.

2. Place inner glass (J) over socket (I).

3. Replace retaining ring (K) and tighten to secure glass. Do not over-tighten.

4. Install light bulb. (Fluorescent bulbs included with fixture)

To Install Lower Glass (Figures 3 & 4)

Component Parts

L Arm Retaining Ring
M Arm (3)
N Lower Glass

1. Loosen arm retaining ring (L).

2. Insert arms (M) into notches by angling the arms so they slip into

notches and pivoting them toward the center until they hang
vertical.

3. Slip lower glass (N) into the arms (M).

4. While supporting the glass tighten the arm retaining ring (L) until

snug. Caution: Arms can swing out causing glass to drop until
retaining ring is completely tight.

5. Restore electricity at main breaker.

(Figure 2)

(Figure 3)

If you need further assistance, or find that you are missing any parts,
please contact the dealer from which you purchased this product. We
hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by
improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 4)

22762