Hubbardton Forge 138810 User Manual
Assembly & Installation Instructions A334
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 1)
(Figure 2)
Apparatus 3 light 13-8810 Page 1 of 4
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Install Mounting Bracket to Ceiling (Figure 1)
Component Parts
A Mounting Bracket
B Anchor (3)
C #10 Screw (3)
D ¼” diameter Rod
E ½” diameter Ball
1. Carefully unpack fixture and canopy from carton.
2. Position the mounting bracket (A) over the electrical b o x
aligning ovals in bracket with mounting holes in electrical
box. Orient fixture to desired hanging position and mark
the location of the anchors (B) on the ceiling. Set the
mounting bracket aside.
3. Drill 1/8” holes in the location marked on the ceiling.
Place the tapered ends of the anchors (B) into the holes and
gently tap flush using a lightweight hammer.
4. Remove ball (E) from one end of ¼”dia rod (D). Slip rod
(D) up through center coupling in mounting bracket (A) and
reattach ball (E).
5. Place mounting bracket (A) over electrical box. Using two machine
screws (not provided) fasten the mounting bracket (A) to the electric
box. Thread the #10 screws (C) through the bracket and into the
anchors (C) to secure the bracket to the ceiling. Be careful not to over
tighten or strip the anchors.
Note: A new electric box comes with screws. When replacing an
existing fixture, retain screws for use with the new fixture.
To Assemble Canopy (Figure 2)
Component Parts
F Hex Nipple (3)
G Lock Washer (3)
H Canopy
I Canopy Pipe (3)
1.
Thread socket wires through canopy.
Line up end of canopy pipe (I) with hole in canopy (H).
2.
Slip lock washer and hex nipple onto wires
3.
4. Place hex nipple (F) through lock washer (G), down through holes in
canopy and thread into canopy pipe. Tighten securely.
5. Repeat steps 2 and 3 for the remaining pipes.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
28308
(continued)
Assembly & Installation Instructions A334
(Figure 3)
Apparatus 3 light 13-8810 Page 2 of 4
To Install Canopy (Figure 3)
Component Parts
A Moun tin g Brac k et
D ¼” Dia Rod
H Canopy
J Support Cable
K #8 Screw
L Cupped Washer
M Green Ground Screw
N Threaded Ring
V Bulb
W Shield
1.
Slide center hole in canopy (H) over ¼”dia rod (D).
Raise canopy (H) close to ceiling. Attach canopy
support cable (J) to mounting bracket(A) using a #8
screw (K). Temporarily suspend canopy using cable
(Figure 3).
temporarily suspend the canopy to help with fixture
installation. Never depend on them to support fixtures
with glass installed.
2. Using suitable wire connectors (not provided) connect
fixture wires to supply (white to white and black to
black). Using cupped washer (L) and green ground
screw (M) run pigtail from mounting bracket (A) to
junction box. Connect all ground wires (bare copper or
green to bare copper or green). Push wires back into
outlet box.
Caution: Make sure wire connectors are twisted on
securely, and no bare wire is exposed.
3. Raise canopy (H) to ceiling, push firmly to ceiling
making sure no wires are pinched between fixture
canopy (H) and ceiling. Secure canopy (H) to mounting
bracket (A) using threaded ring (N).
4. Install bulbs (V). Be careful not to touch bulb with bare
hands; oil from the hands will dramatically reduce bulb
life.
5. Screw shields (W) on to sockets. Do not over tighten.
Caution: The cable is intended to
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
(continued)
28308
Loading...