Hubbardton Forge 138805 User Manual

Assembly & Installation Instructions A333

CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL

(Figure 1)

Apparatus Pendant 138805 Page 1 of 2

INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install to Ceiling (Figure 1)

Component Parts

A Fixture
B Rod
C Ball (2)
D Nipple
E Cupp ed was her
F Ground Screw
G Cover Plate
H Oval Nut

Caution: Be sure power is off at the main breaker
box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Remove ball (C) from one end of the rod (B).

Slide rod (B) through hole in fixture (A) and
replace ball (C).

3. Thread wires from junction box down through

mounting plate on fixture (A).

4. Raise fixture to ceiling aligning holes in

fixture (A) with holes in electric box. Using
two machine screws (not provided) fasten the
fixture (A) to the electric box using outer oval
slots to orient fixture to desired hanging
position.

Note: A new electric box comes with screws.
When replacing an existing fixture retain
screws for use with the new fixture.

5. Thread nipple (D) into center of mounting

bracket on the fixture (A).

6. Using suitable wire connectors (not provided)

connect fixture wires to supply (white to white
and black to black). Using cupped washer (E)
and green ground screw (F) run pigtail from
fixture (A) to junction box. Connect all ground
wires, bare copper or green to bare copper or
green, including fixture ground wire. Push wires back into fixture.

Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.

7. Slip cover plate (G) over nipple (D) and secure using oval nut (H).

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28307

(continued)

Assembly & Installation Instructions A333

(Figure 2)

Apparatus Pendant 138805 Page 2 of 2

To Complete Fixture Assembly (Figure 2)

Component Parts

A Fixture
B Rod
C Ball
I Counterweight.
J Block
K Body
M Thumb Screw
N Thumb Screw (3)
P Glass
Q Bulb
R Shield

1. Install bulb (Q). Be careful not to touch bulb

with bare hands; oil from the hands will
dramatically reduce bulb life.

2. Screw shield (R) onto socket. Do not over

tighten.

3. Loosen the three thumb screws (N). It is not

necessary to remove them from the fixture.

4. Lower glass (P) into fixture body (K) and tighten

thumb screws (N) equally, until snug against
glass.

Remove ball (C) from rod (B). Loosen Thumb

5.

screw (M) from block (J). Slide fixture body (K)
up onto rod (B), slipping the fixture body (K)
over the shield (R). Adjust to desired height and
tighten thumb screw (M).

6. Reattach ball (C) on rod (B)

7. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28307