Page 1
Assembly & Installation Instructions A317
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIO US PERSO NAL
(Figure 1)
(Figure 2)
Aura LED Lg Pendant 13-8589D Page 1 of 3
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Note: Support Cable also acts as Low Voltage Supply Cable.
To Install to Ceiling (Figures 1 thru 5)
Component Parts
A Ceiling Bracket
B Lag Screw (3)
C Canopy
D Canopy Support Cable
E #8 Screw
F Support/supply Cable (3)
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Carefully unpack the fixture from the carton. Put the ceiling
bracket (A) and canopy (C) together, making sure the canopy
mounting holes match up with the ceiling bracket threaded
standoffs. Orient them to achieve desired wire location.
2. Using the three lag screws (B) attach ceiling bracket (A) to a
structural member in the ceiling, centering the crossbar over the
outlet box (Figure 1). Lag screws have been supplied with
your fixture; however, different materials and/or construction
methods may require different fasteners. If in doubt, contact a
qualified electrician. Do not attach crossbar directly to outlet
box.
3. Attach canopy support cable (D) to mounting bracket using a
#8 screw (E). Temporarily suspend canopy using cable (Figure 2).
#8 screw (E) ships installed, it will need to be removed prior to
installation of the support cable (D).
Caution: The cable is intended to temporarily suspend the canopy to
help with fixture installation. Never depend on them to support
fixtures with glass installed.
4. Loosen cable gripper locks before try ing to install cabl es.
Note: Support cable (F) will not be able to pass through the cable
gripper (G) unless the locks are loose.
G Cable Gripper (3)
H Flat Head Screws (2)
I Canopy Nipple
J Canopy Cover
K Knob
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
27825
Page 2
Assembly & Installation Instructions A317
(Figure 3)
(Figure 4)
Aura LED Lg Pendant 13-8589D Page 2 of 3
5. Raise fixture and push support cables (F) through the canopy
(C) and into the cable grippers (G) until desired fixture height
is accomplished and level. Once desired height is
accomplished and product is level, tighten cable gripper locks
(Figure 3).
6. Using heavy duty cable cutters, cut excess supply/support
cable (F) allowing enough left (approx. 4”) to make
connections. Locate support cable (F) w ith a (+) label near
the fixture and slip the red isolation sleeve (provided) over the
end. Locate support cable (F) with a (-) label near the fixture
and slip the black iso lat io n sleeve (provided) over the end.
7. Using suitable wire connectors (provided) connect support
cable (F) with red isolation sleeve to red driver wires with (+)
label attached. Connect support cable (F) with black isolation
sleeve to black driver wires with (-) label attached.
Caution: Make sure wire connectors are on securely, and no
bare wire is exposed.
Note: If using the supplied closed end connector, please use
the MR30A crimping tool. If the correct crimping tool isn’t
available, please use the alternate supplied connector (black
with set screw insert).
8. Remove canopy support cable (D) by removing #8 screw
(E) from one end and #8 nut from other end (dis card cable).
Note: Flat head screws (H) will need to be removed from
ceiling bracket (A) prior to installation of the canopy (C).
The screws are shipped installed.
9. Raise the canopy (C) to the ceiling and attach to ceiling
bracket (A) with two flat head screws (H). (Figure 4).
10. Using suitable wire connectors (not provided) connect
fixture wires to supply (white to white or ribbed, black to
black or smooth). Connect all ground wires.
Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.
11. Thread canopy nipple (I) into threaded hole directly in
center of ceiling bracket (A).
12. Install canopy cover (J) on canopy nipple (I) (Figure 5, next
page).
13. Thread knob (K) on to canopy nipple (I). Tighten against
canopy cover (J) until snug
.
14. Refer to instructions following to install glass.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
27825
Page 3
Assembly & Installation Instructions A317
(Figure 5)
(Figure 6)
Aura LED Lg Pendant 13-8589D Page 3 of 3
Install Glass (Figure 6)
Component Parts
L Glass (6)
1. Slip glass (L) into slots in fixture between bulb locations.
2. Repeat for all six locations.
3. Restore electricity at the main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
27825
Loading...