Hubbardton Forge 137860 User Manual

Assembly & Installation Instructions A108

After Hours Pendant 13-7860F Page 1 of 3

To Assemble Pipe to Fixture (Figure 1)

Component Parts

A Fixture Pipe
B Fixture

1. Carefully unpack the fixture from the carton.

2. Carefully thread fixture pipe (A), threaded end first, over fixture wires.

3. Apply a drop of the supplied thread locking compound to the internal threads at the top of the

fixture (B) and screw stem into fixture, being careful not to twist the wires.

Note: Application of the thread locking compound is necessary to prevent the stem from
loosening during regular maintenance and cleaning of the fixture. Be certain to apply the
compound.

4. See instructions on next page to complete the installation.

(Figure 1)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

19820 Rev B

Assembly & Installation Instructions A108

After Hours Pendant 13-7860F Page 2 of 3

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Complete Fixture Assembly (Figures 2 & 3)

Component Parts

A Fixture Pipe
C Canopy
D Crossbar
E Ground Screw
F Threaded Stud (2)
G Barrel Knob (2)
H Canopy Pipe
I Plastic Clutch Sleeve
J Clutch
K Set Screw

Caution: Be sure power is off at the main breaker box prior to installation.

(Figure 2)

1. Thread the wires from the fixture pipe (A) into and through the canopy pipe (H)

up through the canopy (C).

2. Unscrew the clutch (J) from the canopy pipe (H); slide it across the wires and

onto the fixture pipe (A). Follow this with the plastic clutch sleeve (I), oriented
so the tapered end of the clutch sleeve nests in the clutch.

3. Slide the canopy pipe (H) as far as necessary to give you the total length of the

fixture which you desire. Be careful not to scratch the pipe surfaces and to pull
excess wire up through the canopy pipe (H). Screw clutch (J) onto canopy pipe
(H). There must be a minimum 1-1/2" of inner pipe inside the outer pipe. Hand­tighten the clutch to temporarily hold this adjustment. The clutch is not securely
fastened at this point; do not depend on it to hold the fixture.

Important: To ensure full connection strength, be sure the tapered end of the
plastic clutch sleeve is oriented toward the clutch when assembled and securely
tighten set screw (Figure 2).

4. Using suitable wire connectors (not provided), connect ballast wires to lamp

wires (red to red, yellow to blue) and the green ground wire to ground screw (E)
on the crossbar. Push wire nuts to the inside of canopy (C) next to ballast
making sure not to cover the mounting holes in the canopy.

5. Thread studs (F) through appropriate holes in crossbar (D) to match holes in

canopy (C).

6. Using two machine screws (not provided), fasten the crossbar (C) to the electric

box.

Note: A new electric box comes with screws. When replacing a fixture, retain the
existing screws for use with the new fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 2)

(Figure 3)

(continued)

19820 Rev B

Assembly & Installation Instructions A108

After Hours Pendant 13-7860F Page 3 of 3

7. Using suitable wire connectors (not provided) connect fixture wires to supply (white to white or ribbed and black to

black or smooth). Connect all ground wires to green ground screw (E).

Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.

8. Slide canopy (C) over threaded studs (F) and push firmly to ceiling, making sure that no wires are pinched between

fixture canopy and ceiling. Fasten with barrel knobs (G). Be sure studs are fully seated in the barrel knobs.

9. Once the fixture is fastened to the ceiling, tighten the set screw (K) in clutch (J) firmly with hex wrench provided.

Only after the set screw (K) is tight should you install the glass.

10. Refer instructions below and install glass.

To Install Bulb and Glass

Component Parts

L Lock
M Glass Frame
N Bulb (not included)
O Glass Tube
P Bottom Plate

1. Unscrew lock (L) and slide lock (L), glass frame (M) up fixture stem.

2. Install bulb (N) into sockets. Orient bulb pins to slip in slots in the sockets. Turn the

bulb until the sockets lock in position. (Bulb should not be able to be pulled out of
sockets once it is locked in place).

3. Slip glass (O) over bulb (N) location and place inside glass frame (M).

4. Lower glass frame (M) and glass tube (O) so that the bottom notches are aligned with

the tabs on the bottom plate (P).

5. Screw lock (L) down on top of glass frame (M) until tight.

If you need further assistance, or find that you are missing any parts, please contact the
dealer from which you purchased this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

(Figure 4)

(Figure 4)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19820 Rev B