Page 1
Assembly & Installation Instructions A126
(Fig
2
)
For Steppe Pendant 13-7710 Page 1 of 4
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Attach Fixture Pipes (Figure 1)
Component Parts
A Fixture Pipe
B Fixture Coupling
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipe (A), threaded end first, over
fixture wires.
3. Apply a drop of the supplied thread locking compound to
the internal threads at the top of the fixture (B) and screw
stem into fixture, being careful not to twist the wires.
Note: Application of the thread locking compound is
necessary to prevent the stem from loosening during
regular maintenance and cleaning of the fixture. Be certain
to apply the compound.
4. See instructions below to complete the installation.
To Assemble Canopy Pipes to Ceiling Bracket
Component Parts
C Hex Nipple (2)
D Lock Washer (2)
E Ceiling Bracket
F Canopy Pipes (2)
(Figure 2)
1. Insert threaded end of hex nipple (C) down through lock washer (D), ceiling
bracket (E) and into swivel at the end of canopy pipe (F).
2. Tighten securely being sure the notches in the swivels are aligned.
Note: If installing on a sloped ceiling, make certain that the notches in the swivel
portion of the stems are oriented toward the lower side of the slope.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 1)
ure
(continued)
19910 Rev A
Page 2
Assembly & Installation Instructions A126
For Steppe Pendant 13-7710 Page 2 of 4
To Complete Fixture Assembly
Component Parts
A Fixture Pipe (2) H Plastic Clutch Sleeve (2)
C Hex Nipple I Set Screw (2)
F Canopy Pipe (2) J Canopy
G Clutch (2)
Caution: Be sure power is off at the main breaker box prior
to installation.
(Figures 3 & 4)
1. Thread wires from the fixture pipe (A) through canopy (J).
Slide canopy (J) down fixture pipe (A) until it rest on top
of fixture.
2. Thread the wires from the fixture pipe (A) into and
through the canopy pipe (F) up through the hex nipple (C).
3. Unscrew the clutch (G) from the canopy pipe (F); slide it
across the wires and onto the fixture pipe (A). Follow this
with the plastic clutch sleeve (H), oriented so the tapered end
of the clutch sleeve nests in the clutch. (Figure 3)
4. Slide the canopy pipe (F) as far as necessary to give you the total length of
the fixture which you desire. Be careful not to scratch the pipe surfaces and
to pull excess wire up through the canopy pipe (F). Screw clutch (G) onto
canopy pipe (F). There must be a minimum 1-1/2" of inner pipe inside the
outer pipe. Hand-tighten the clutch to temporarily hold this adjustment.
The clutch is not securely fastened at this point; do not depend on it to hold
the fixture.
Important: To ensure full connection strength, be sure the tapered end of
the plastic clutch sleeve is oriented toward the clutch when assembled and
securely tighten set screw (Figure 3).
5. Continue with Ceiling Installation below.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 3)
(Figure 4)
(continued)
19910 Rev A
Page 3
Assembly & Installation Instructions A126
For Steppe Pendant Fixture 13-7710 Page 3 of 4
To Install to Ceiling
Component Parts
E Ceiling Bracket
I Set Screw (2)
J Canopy
L Crossbar
M Stud (2)
(Figures 5)
N Lag Screw (4)
O Threaded Stud (2)
P Hex Nut (2)
Q Barrel Knob (2)
1. Thread studs (O) through appropriate holes in crossbar (L) to match
holes in canopy (J).
2. Using four lag screws (N) attach crossbar (L) to a structural member in
the ceiling, centering the crossbar over the outlet box. We've supplied
lag screws with your fixture; however, different materials and/or
construction methods may require different fasteners. If in doubt,
contact a qualified electrician. Do not attach crossbar directly to outlet
box.
3. Raise fixture to ceiling aligning studs in crossbar (L) with holes in
ceiling bracket (E).
4. Thread hex nut (P) onto studs (M) and tighten.
5. Using suitable wire connectors (not provided) connect fixture wires to
supply (white to white and black to black, and bare copper to bare
copper or green supply). Push wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.
6. Raise canopy (J) to ceiling over threaded studs (O) and push firmly to
ceiling, making sure that no wires are pinched between canopy and
ceiling. Fasten with barrel knob (Q).
notches are aligned in the same direction. For sloped ceilings the
notches should face towards the down side.
Note: Be sure both swivel
7. Once the fixture is fastened to the ceiling, tighten the set screw (I) firmly
with hex wrench provided. Only after the set screw (I) is tight should
you install the glass.
8. Refer instructions below and install glass.
9. Install light bulbs (not included).
10. Restore electricity at main breaker.
(Figure 5)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19910 Rev A
Page 4
Assembly & Installation Instructions A126
For Steppe Pendant Fixture 13-7710 Page 4 of 4
To Install Glass
Component Parts
R Large Glass Panels (2)
S Small Glass Panels (2)
T Steel Bar
U Bottom Glass
1. Insert two large glass panels (R) into the slots in the upper tier of
the fixture, centering the panels side to side.
2. Insert two small glass panels (S) into the slots in the upper tier of
the fixture, centering the panels side to side.
3. Slide bottom glass (U) into slot in bottom tier of fixture, on top of
steel bars.
4. Drop steel bar (T) into slots at corners of bottom tier of fixture to
secure glass.
(Figure 6)
(Figure 6)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19910 Rev A
Loading...