Page 1
Assembly & Installation Instructions A326
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 1)
(Figure 2)
Moreau Shade Pendant 13-7655 Page 1 of 4
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Attach Fixture Pipes (Figure 1)
Component Parts
A Fixture Pipe
B Fixture Coupling
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipe (A), threaded end first, over fixture
wires.
3. Apply a drop of the supplied thread locking compound to the
internal threads at the top of the fixture (B) and screw stem into
fixture, being careful not to twist the wires.
Note: Application of the thread locking compound is necessary
to prevent the stem from loosening during regular maintenance
and cleaning of the fixture. Be certain to apply the compound.
4. See instructions below to complete the installation.
To Assemble Canopy Pipes to Ceiling Bracket (Figure 2)
Component Parts
C Hex Nipple (2)
D Lock Washer (2)
E Ceiling Bracket
F Canopy Pipes (2)
1. Insert threaded end of h ex nipple (C) down through
lock washer (D), ceiling bracket (E) and into swivel
at the end of canopy pipe (F).
Note: Ceiling bracket oriented with threaded studs
pointing downward.
2. Tighten securely being sure the notches in the
swivels are aligned.
Note: If installing on a sloped ceiling, make certain
that the notches in the swivel portion of the stems
are oriented toward the lower side of the slope.
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
28104
Page 2
Assembly & Installation Instructions A326
(Figure 3)
(Figure 4)
Moreau Shade Pendant 13-7655 Page 2 of 4
To Complete Fixture Assembly (Figures 3 & 4)
Component Parts
A Fixture Pipe (2)
C Hex Nipple
F Canopy Pipe (2)
G Clutch (2)
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Thread wires from the fixture pipe (A) through canopy (J).
Slide canopy (J) down fixture pipe (A) until it rest on top of fixture.
2. Thread the wires from the fixture pipe (A) into and through the
canopy pipe (F) up through the hex nipple (C).
3. Unscrew the clutch (G) from the canopy pipe (F); slide it across the
wires and onto the fixture pipe (A). Follow this with the plastic
clutch sleeve (H), oriented so the tapered end of the clutch sleeve
nests in the clutch (F igure 3).
4. Slide the canopy pipe (F) as far as necessary to give you the total
length of the fixture which you desire. Be careful not to scratch the
pipe surfaces and to pull excess wire up through the canopy pipe
(F). Screw clutch (G) onto canopy pipe (F). There must be a
minimum 1-1/2" of inner pipe inside the outer pipe. Hand-tighten
the clutch to temporarily hold this adjustment. The clutch is not
securely fastened at this point; do not depend on it to hold the
fixture.
Important: To ensure full connection strength, be sure the tapered
end of the plastic clutch sleeve is oriented toward the clutch when
assembled and securely tighten set screw (Figure 3)
5. Continue with Ceiling Installation below.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
H Plastic Clutch Sleeve (2)
I Set Screw (2)
J Canopy
.
(continued)
28104
Page 3
Assembly & Installation Instructions A326
(Figure 5)
Moreau Shade Pendant 13-7655 Page 3 of 4
To Install to Ceiling (Figure 5)
Component Parts
E Ceiling Brack et
I Set Screw (2)
J Canopy
1. Thread studs (N) through approp riate holes in
ceiling bracket (E) to match holes in canopy
(J) as seen in Figure 5.
2. Using two machine screws (not provided)
fasten the crossbar (L) to the electric box
using outer oval slots to orient fixture to
desired hanging position.
Note: A new electric box comes with screws.
When replacing an existing fixture, retain
screws for use with the new fixture.
3. Raise fixture to ceiling aligning holes in
crossbar (L) with holes in ceiling bracket (E)
install two #8 screws (M).
4. Using suitable wire connectors (not provided)
connect fixture wires to supply (white to white
and black to black). Run a pigtail lead from
crossbar ground screw (P) to the junction box
and connect all ground wires (bare copper or
green to bare copper or green).Push wires
back into outlet box.
Caution: Make sure wire connectors are
twisted on securely, and no bare wire is
exposed.
5. Raise canopy (J) to ceiling over threaded studs
(N) and push firmly to ceiling, making sure
that no wires are pinched between canopy and
ceiling. Fasten with barrel knob (O).
Note: Be sure both swivel notches are aligned
in the same direction. For sloped ceilings the
notches should face towards the down side.
6. Once the fixture is fastened to the ceiling,
tighten the set screws (I) firmly with hex
wrench provided. Only after the set screws (I)
are tight should you install the glass.
7. Refer instructions following to install diffuser and shade.
L Crossbar
M #8 Screw (2)
N Threaded Stud (2)
O Barrel Knob (2)
P Gr ound Scr e w
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
28104
Page 4
Assembly & Installation Instructions A326
(Figure 6)
(Figure 7)
Moreau Shade Pendant 13-7655 Page 4 of 4
Fixture Assembly (Figures 6 & 7)
Component Parts
Q Hex Nut (2)
R Diffuser
S Lo wer Ass embly
T Shade
U Thumb Screw with Washer and Hex Nut (2)
V Fixture
1. Slip diffuser (R) onto lower assembly (S).
2. Raise lower assembly (S) and diffuser (R) so the
threaded studs pass through the top of the fixture (V).
3. Install two hex nuts (Q) onto the threaded studs and
tighten.
4. Install bulbs (not included).
See Figure 7 for remaining steps.
5. Remove thumb screw assembly (U) from top of fixture
(V). Save for later use. Thumb screws are shipped
installed.
6. Install shade (T) from the bottom and tilt so it will pass fixture (V). It will be necessary to raise one side of the
shade completely past the diffuser and over towards the canopy pipes as far as it will go to allow the other side of
the shade to pass the diffuser. Lower the shade (T) so it rests on top of the fixture (V).
7. Secure the shade (T) with the thumb screws (U).
8. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
28104
Loading...