Page 1
Assembly & Installation Instructions A300
Facet Pendant 13-7620 Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Install to Ceiling (Figures 1 thru 5)
Component Part
A Ceiling Bracket
B Cable Gripper (2)
C Gripper Nut (2)
D Canopy
E Support Cable (2)
F Fixture
Caution: Be sure power is off at the main breaker
box prior to
installation.
1. Carefully unpack the fixture from the carton.
2. Using two machine screws (not provided),
fasten the ceiling bracket (A) to the electric
box.
Note: A new electric box comes with screws.
When replacing a fixture, retain the existing
screws for use with the new fixture.
3. Slip gripper nuts (C) onto the support cables
(E) and allow to rest on top of fixture (F).
4. Pull support cables (E) and supply wire (G)
through canopy (D) allowing canopy to rest on
top of fixture (F).
5. Raise fixture and push support cables (E)
through cable grippers (B) until desired fixture
height is accomplished and level.
6. Slip supply wire (G) through strain relief (H)
and push supply wire (G) through slot on the
bottom of ceiling bracket (A) followed by
washer (I). Adjust location of strain relief (H)
on supply wire (G) until it will snap into
location provided on ceiling bracket (A). Note:
Make sure orientation of slot in the ceiling
bracket matches location of supply wire from fixture.
7. Snap strain relief (H) onto supply wire (G) and push into tab on ceiling bracket (Figure 3).
8. Once support cables are at the correct height, excess cable can be cut off. To keep the strands of cable together a
small piece of electrical tape can be applied to the cut end.
9. Cut excess supply wire (G) allowing enough left (approx. 6”) to make connections in the electrical box. Strip
outside jacket being careful not to cut through shielding of the two inner conductors.
G Supply wire
H Strain Relief
I Washer
J Cupped Washer
K Hex Nut
(Figure 1)
(Figure 2)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27150
Page 2
Assembly & Installation Instructions A300
Facet Pendant 13-7620 Page 2 of 3
10. Run a pigtail lead from the ceiling bracket (A) using cupped
washer (J) and hex nut (K) to the junction box. Using suitable
wire connectors (not provided) connect unshielded wire from
supply wire (G) to all ground wires (bare copper or green
shielded) (Figure 4).
11. Using suitable wire connectors (not provided) connect fixture
wires to supply (wire with white tracer to white and wire with
no tracer to black).
twisted on securely, and no bare wire is exposed.
12. Raise canopy (D) and push firmly to ceiling making sure that
no wires are pinched between fixture canopy and ceiling.
Fasten to ceiling by threading gripper nuts (C) onto grippers
(B) (Figure 5).
Caution: Make sure wire connectors are
(Figure 3)
(Figure 4)
Fixture Assembly
Component Parts
L Hex Nut (2)
M Diffuser
N Lower Assembly
O Shade
P Thumb Screw with Washer and Hex Nut (2)
Q Fixture
(Figures 6 & 7)
1. Remove hex nuts (L) from lower assembly (N). Save
for later use. Hex nuts are shipped installed.
2. Slip diffuser (M) onto lower assembly (N).
3. Raise lower assembly (N) and diffuser (M) so the
threaded studs pass through the top of the fixture (Q).
4. Install two hex nuts (L) onto the threaded studs and
tighten.
(Figure 6)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27150
(Figure 5)
(continued)
Page 3
Assembly & Installation Instructions A300
Facet Pendant 13-7620 Page 3 of 3
5. Install bulbs. (Not Included)
See Figure 7 for remaining steps.
6. Remove thumb screw assembly (P) from top
of fixture (Q). Save for later use. Thumb
screws are shipped installed.
7. Install shade (O) from the bottom and tilt so it
will pass fixture (Q). It will be necessary to
raise one side of the shade completely past
the diffuser and over towards the canopy
pipes as far as it will go to allow the other
side of the shade to pass the diffuser. Lower
the shade so it rests on top of the fixture.
8. Secure the shade (O) with the thumb screw
assembly (P).
9. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(Figure 7)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27150
Loading...