Assembly & Installation Instructions A217
For Ellipse Large Nine Light Pendant 13-7531 & 13-7531E Page 1 of 4
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Stem Assembly (Figure 1)
Component Parts
A Fixture Pipe (3)
B Fixture Coupling (3)
C Support Cable (3)
D Decorative Caps (3)
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipe (A), threaded end first, over
fixture wires.
3. Apply a drop of the supplied thread locking compound to
the internal threads of fixture coupling (B) and screw
stem into fixture, being careful not to twist or pinch the
wires.
Note: Application of the thread locking compound is
necessary to prevent the stem from loosening during
regular maintenance and cleaning of the fixture. Be
certain to apply the compound.
4. Thread decorative caps (C) to top of fixture pipes (A).
5. See instructions below to complete the installation.
(Figure 1)
Install Canopy Pipes
Component Parts
E Canopy Coupling (3)
F Canopy Pipe (3)
(Figure 2)
1. Apply a drop of the supplied thread locking compound to the internal threads
of canopy coupling (E) and screw canopy pipe (F) into coupling.
Note: Application of the thread locking compound is necessary to prevent the
stem from loosening during regular maintenance and cleaning of the fixture. Be
certain to apply the compound.
2. See instructions following to complete the installation.
(Figure 2)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22896
Assembly & Installation Instructions A217
(Fig
3
)
For Ellipse Large Nine Light Pendant 13-7531 & 13-7531E Page 2 of 4
To Install to Ceiling (Figures 3 thru 5)
Component Parts
C Support Cable
G Canopy Assembly
H Fixture Assembly
I Ceiling Bracket
J Lag Screws (4)
Caution: Be sure power is off at the main breaker
box prior to
installation.
K Cable Gripper
L Safety Nut
M Threaded Cap
N Threaded Stud
O Ground Screw
1. Using four lag screws (J) attach ceiling bracket (I) to
a structural member in the ceiling, centering the
crossbar over the outlet box. We've supplied lag
screws with your fixture; however, different
materials and/or construction methods may require
different fasteners. If in doubt, contact a qualified
electrician. Do not attach ceiling bracket directly to
outlet box (Figure 3).
2. Install threaded stud (N) into ceiling bracket (I) a
couple of threads followed by lock nut (W).
3. Raise canopy assembly (G) to ceiling and align so
the threaded stud (N) passes through the canopy.
Adjust threaded stud (N) until it protrudes
approximately 3/16” through the bottom of the
canopy assembly (G). Lower canopy assembly (G) and tighten lock nut
(W) to maintain the threaded studs height.
4. Thread wires and support cable (C) from the fixture assembly (H)
through the canopy assembly (G) (Figure 4).
5. Loosen the three safety nuts (L) on cable grippers (K). It is not
necessary to completely remove them (Figure 5).
6. Raise fixture and push support cables (C) into cable grippers threading
them through ceiling bracket (I) as shown in Figure 5 until cables are
tight and have no slack. Push cables through grippers until desired fixture
height is accomplished.
7. Once support cable is at the correct height, excess cable behind the
gripper can be cut off.
8. Tighten safety nuts (L).
9. Using suitable wire connectors (not provided) connect fixture wires to
supply (white to white and black to black, and bare copper to bare copper
or green supply). Connect all ground wires to green ground screw (O)
and cupped washer (P). Push wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.
10. Raise canopy assembly (G) to ceiling making sure the fixture pipes and
canopy pipes over lap. Attach safety cable (X) from the canopy assembly to
the ceiling bracket using screw (Y).
11. Refer to instructions following to install glass.
P Cupped Washer
W Lock Nut
X Safety Cable
Y Cable Screw
ure
(Figure 4)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22896
Assembly & Installation Instructions A217
For Ellipse Large Nine Light Pendant 13-7531 & 13-7531E Page 3 of 4
(Figure 5)
Install Glass on G9 Version
Component Parts
Q Bulb Shield (9)
R Bulb (supplied) (9)
S Washer (9)
T Glass (9)
U Socket (9)
(Figure 6)
1. Install bulb (supplied). Be careful not to touch bulb with bare
hands; oil from the hands will dramatically reduce bulb life.
2. Place glass (T) over socket (U).
3. Place washer (S) over socket (U) until it rests on the bottom inside
of glass (T).
4. Thread bulb shield (Q) onto Socket (U). Future bulb changes may
be accomplished by snapping glass bulb shield on and off rather
than unthreading the holder.
5. Restore electricity at the main breaker.
(Figure 6)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
22896
Assembly & Installation Instructions A217
For Ellipse Large Nine Light Pendant 13-7531 & 13-7531E Page 4 of 4
Install Glass on GU24 Version
Component Parts
R Bulb (supplied) (9)
T Glass (9)
U Socket (9)
V Retaining Ring (9)
(Figure 7)
1. Remove retaining ring (V) from socket (U). Retaining Rings are
shipped installed.
2. Place glass (T) over socket (U).
3. Replace retaining ring (V) and tighten to secure glass. Do not over-
tighten.
4. Install light bulb (supplied).
5. Restore electricity at the main breaker.
(Figure 7)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22896
Loading...