Hubbardton Forge 137527 User Manual

Assembly & Installation Instructions A216

For Ellipse Large Five Light Pendant 13-7527 & 13-7527E Page 1 of 3

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Install Fixture Pipes (Figure 1)

Component Parts

A Fixture Pipe (2)
B Fixture Coupling (2)
C Support Cable

1. Carefully unpack the fixture from the carton.

2. Carefully thread fixture pipe (A), threaded end first, over fixture

wires and support cable (C).

3. Apply a drop of the supplied thread locking compound to the

internal threads of fixture coupling (B) and screw pipe into fixture,
being careful not to twist or pinch the wires.

Note: Application of the thread locking compound is necessary to
prevent the stem from loosening during regular maintenance and
cleaning of the fixture. Be certain to apply the compound.

4. See instructions following to complete the installation.

(Figure 1)

Install Canopy Pipes

Component Parts

D Canopy Coupling (2)
E Canopy Pipe (2)
F Decorative Caps (2)

(Figure 2)

1. Apply a drop of the supplied thread locking compound to the internal

threads of canopy coupling (D) and screw canopy pipe (E) into coupling.

Note: Application of the thread locking compound is necessary to prevent
the stem from loosening during regular maintenance and cleaning of the
fixture. Be certain to apply the compound.

2. Thread decorative caps (F) to bottom of canopy pipes (E).

3. See Figure 6. Remove barrel knobs (O) and wireway cover (N) from

canopy. Save for later use.

4. See instructions following to complete the installation.

(Figure 2)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22885

Assembly & Installation Instructions A216

For Ellipse Large Five Light Pendant 13-7527 & 13-7527E Page 2 of 3

To Install to Ceiling

Component Parts

C Support Cable
G Canopy Assembly
H Fixture Assembly
I Ceiling Bracket
J Lag Screws (4)

Caution: Be sure power is off at the main breaker box prior to

1. Using four lag screws (J) attach ceiling bracket (I) to a

structural member in the ceiling, centering the crossbar over
the outlet box. We've supplied lag screws with your fixture;
however, different materials and/or construction methods
may require different fasteners. If in doubt, contact a
qualified electrician. Do not attach crossbar directly to outlet
box (Figure 3).

2. Thread wires and support cable (C) from the fixture

assembly (H) through the canopy assembly (G) (Figure 4).

3. Loosen both safety nuts (L) on cable grippers (K). It is not

necessary to completely remove them (Figure 5).

4. Raise fixture and push support cables (C) into cable grippers

threading them through ceiling bracket (I) as shown in figure 5
until cables are tight and have no slack. Push cables through
grippers until desired fixture height is accomplished.

5. Raise canopy assembly (G) to ceiling making sure the fixture

pipes and canopy pipes over lap. Fasten to ceiling bracket (I) with
flat head screws (M).

6. Once support cable is at the correct height, excess cable behind

the gripper can be cut off.

7. Tighten safety nuts (L).

8. Using suitable wire connectors (not provided) connect fixture

wires to supply (white to white and black to black, and bare
copper to bare copper or green supply). Ground the ceiling
bracket (I) using the green ground screw (P) and cupped washer
(Q) to secure a pigtail lead to the bracket. Push wires back into
outlet box.
Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.

9. Install the wireway cover (N) and secure with barrel knobs (O)

(Figure 6).

10. Refer to instructions following to install glass.

(Figures 3 thru 6)

K Cable Gripper (2)
L Safety Nut (2)
M Flat Head Screws
N Wireway Cover
O Barrel Knobs (2)

(2)

P Ground Screw
Q Cupped Washer

installation.

(Figure 3)

(Figure 4)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22885