Hubbardton Forge 137525 User Manual

Assembly & Installation Instructions A134

For Ellipse Pendants 13-7525, 13-7525F, 13-7535 & 13-7535F Page 1 of 4

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Attach Fixture Pipes (Figure 1)

Component Parts

A Fixture Pipe
B Fixture Coupling

1. Carefully unpack the fixture from the carton.

2. Carefully thread fixture pipe (A), threaded end first, over fixture

wires.

3. Apply a drop of the supplied thread locking compound to the

internal threads at the top of the fixture (B) and screw stem into
fixture, being careful not to twist the wires.

Note: Application of the thread locking compound is necessary
to prevent the stem from loosening during regular maintenance
and cleaning of the fixture. Be certain to apply the compound.

4. See instructions below to complete the installation.

(Figure 1)

To Assemble Canopy Pipes to Ceiling Bracket

(Figure 2)

This illustration represents a typical fixture

and may not match every style.

Component Parts

C Hex Nipple (2)
D Lock Washer (2)
E Ceiling Bracket
F Canopy Pipes (2)

1. Insert threaded end of hex nipple (C) down through lock washer (D),

ceiling bracket (E) and into swivel at the end of canopy pipe (F).

2. Tighten securely being sure the notches in the swivels are aligned.

Note: If installing on a sloped ceiling, make certain that the notches in
the swivel portion of the stems are oriented toward the lower side of
the slope.

(Figure 2)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

20928 Rev B

Assembly & Installation Instructions A134

For Ellipse Pendants 13-7525, 13-7525F, 13-7535 & 13-7535F Page 2 of 4

To Complete Fixture Assembly

Component Parts

A Fixture Pipe (2)
C Hex Nipple
F Canopy Pipe (2)
G Clutch (2)

Caution: Be sure power is off at the main breaker box prior
to installation.

(Figures 3 & 4)

H Plastic Clutch Sleeve (2)
I Set Screw (2)
J Canopy

1. Thread wires from the fixture pipe (A) through canopy (J).

Slide canopy (J) down fixture pipe (A) until it rest on top
of fixture.

2. Thread the wires from the fixture pipe (A) into and

through the canopy pipe (F) up through the hex nipple (C).

3. Unscrew the clutch (G) from the canopy pipe (F); slide it

across the wires and onto the fixture pipe (A). Follow this
with the plastic clutch sleeve (H), oriented so the tapered end
of the clutch sleeve nests in the clutch (Figure 3).

4. Slide the canopy pipe (F) as far as necessary to give you the total

length of the fixture which you desire. Be careful not to scratch the
pipe surfaces and to pull excess wire up through the canopy pipe (F).
Screw clutch (G) onto canopy pipe (F). There must be a minimum
1-1/2" of inner pipe inside the outer pipe. Hand-tighten the clutch to
temporarily hold this adjustment. The clutch is not securely fastened
at this point; do not depend on it to hold the fixture.

Important: To ensure full connection strength, be sure the tapered
end of the plastic clutch sleeve is oriented toward the clutch when
assembled and securely tighten set screw

(Figure 3).

5. Continue with Ceiling Installation below.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 3)

(Figure 4)

(continued)

20928 Rev B

Assembly & Installation Instructions A134

For Ellipse Pendants 13-7525, 13-7525F, 13-7535 & 13-7535F Page 3 of 4

To Install to Ceiling

Component Parts

E Ceiling Bracket
I Set Screw (2)
J Canopy

1. Thread studs (O) through appropriate holes in crossbar

(L) to match holes in canopy (J).

2. Using two machine screws (not provided) fasten crossbar

(L) to the electric box using tab holes to orient fixture to
desired hanging position.

comes with screws. When replacing an existing fixture,
retain the screws for use with the new fixture.

Alternate Mounting Option - Using four lag screws (N)
attach crossbar (L) to a structural member in the ceiling,
centering the crossbar over the outlet box. We've
supplied lag screws with your fixture; however, different
materials and/or construction methods may require
different fasteners. If in doubt, contact a qualified
electrician.

3. Raise fixture to ceiling aligning studs in crossbar (L) with

holes in ceiling bracket (E).

4. Thread hex nut (P) onto studs (M) and tighten.

5. Using suitable wire connectors (not provided) connect

fixture wires to supply (white to white and black to black,
and bare copper to bare copper or green supply). Push
wires back into outlet box.

Caution: Make sure wire connectors are twisted on

securely, and no bare wire is exposed.

6. Raise canopy (J) to ceiling over threaded studs (O) and

push firmly to ceiling, making sure that no wires are
pinched between canopy and ceiling. Fasten with barrel
knob (Q).

Note: Be sure both swivel notches are aligned in the same direction. For sloped ceilings the notches should face
towards the down side.

7. Once the fixture is fastened to the ceiling, tighten the set screw (I) firmly with hex wrench provided. Only after the

set screw (I) is tight should you install the glass.

8. Refer instructions below and install glass.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 5)

Note: A new electric box

L Crossbar
M Stud (2)
N Lag Screw (4)

O Threaded Stud (2)
P Hex Nut (2)
Q Barrel Knob (2)

(Figure 5)

(continued)

20928 Rev B

Assembly & Installation Instructions A134

For Ellipse Pendants 13-7525, 13-7525F, 13-7535 & 13-7535F Page 4 of 4

To Install Glass

Component Parts

R Socket (5)
S Glass (5)
T Retaining Ring (5)
U Socket Tool

1. Slip glass (S) over socket (R).

2. Thread retaining ring (T) onto socket using socket tool provided

(U) until it rests on inside of glass (S). Do not over tighten.

3. Install light bulbs and restore electricity at main breaker.

(Figure 6)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

(Figure 6)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

20928 Rev B