Page 1
Assembly & Installation Instructions A136
For Ellipse Pendants 13-7523 & 137523F Page 1 of 4
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Attach Fixture Pipes (Figure 1)
Component Parts
A Fixture Pipe
B Fixture Coupling
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipe (A), threaded end first, over fixture wires.
3. Apply a drop of the supplied thread locking compound to the internal
threads at the top of the fixture (B) and screw stem into fixture, being
careful not to twist the wires.
Note: Application of the thread locking compound is necessary to prevent
the stem from loosening during regular maintenance and cleaning of the
fixture. Be certain to apply the compound.
4. See instructions below to complete the installation.
To Assemble Canopy Pipes to Ceiling Bracket
Component Parts
C Hex Nipple (2)
D Lock Washer (2)
E Ceiling Bracket
F Canopy Pipes (2)
(Figure 2)
1. Insert threaded end of hex nipple (C) down through lock washer (D),
ceiling bracket (E) and into swivel at the end of canopy pipe (F).
2. Tighten securely being sure the notches in the swivels are aligned.
Note: If installing on a sloped ceiling, make certain that the notches in
the swivel portion of the stems are oriented toward the lower side of
the slope.
(Figure 1)
(Figure 2)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21041 Rev B
Page 2
Assembly & Installation Instructions A136
For Ellipse Pendants 13-7523 & 137523F Page 2 of 4
To Complete Fixture Assembly
Component Parts
A Fixture Pipe (2)
C Hex Nipple
F Canopy Pipe (2)
G Clutch (2)
Caution: Be sure power is off at the main breaker box prior
to installation.
(Figures 3 & 4)
H Plastic Clutch Sleeve (2)
I Set Screw (2)
J Canopy
1. Thread wires from the fixture pipe (A) through canopy (J).
Slide canopy (J) down fixture pipe (A) until it rests on top
of fixture.
2. Thread the wires from the fixture pipe (A) into and
through the canopy pipe (F) up through the hex nipple (C).
3. Unscrew the clutch (G) from the canopy pipe (F); slide it
across the wires and onto the fixture pipe (A). Follow this
with the plastic clutch sleeve (H), oriented so the tapered end
of the clutch sleeve nests in the clutch (Figure 3).
4. Slide the canopy pipe (F) as far as necessary to give you the total
length of the fixture which you desire. Be careful not to scratch
the pipe surfaces and to pull excess wire up through the canopy
pipe (F). Screw clutch (G) onto canopy pipe (F). There must be a
minimum 1-1/2" of inner pipe inside the outer pipe. Hand-tighten
the clutch to temporarily hold this adjustment. The clutch is not
securely fastened at this point; do not depend on it to hold the
fixture.
Important: To ensure full connection strength, be sure the
tapered end of the plastic clutch sleeve is oriented toward the
clutch when assembled and securely tighten set screw
(Figure 3).
5. Continue with Ceiling Installation.
(Figure 3)
(Figure 4)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21041 Rev B
Page 3
Assembly & Installation Instructions A136
For Ellipse Pendants 13-7523 & 137523F Page 3 of 4
To Install to Ceiling
Component Parts
E Ceiling Bracket
I Set Screw (2)
J Canopy
1. Thread studs (O) through appropriate holes in crossbar (L) to
match holes in canopy (J).
2. Using two machine screws (not provided) fasten crossbar (L) to
the electric box using tab holes to orient fixture to desired hanging
position.
replacing an existing fixture, retain the screws for use with the new
fixture.
Note: A new electric box comes with screws. When
Alternate Mounting Option - Using four lag screws (N) attach
crossbar (L) to a structural member in the ceiling, centering the
crossbar over the outlet box. We've supplied lag screws with your
fixture; however, different materials and/or construction methods
may require different fasteners. If in doubt, contact a qualified
electrician.
3. Raise fixture to ceiling aligning studs in crossbar (L) with holes in
ceiling bracket (E).
4. Thread hex nut (P) onto studs (M) and tighten.
5. Using suitable wire connectors (not provided) connect fixture
wires to supply (white to white and black to black, and bare copper
to bare copper or green supply). Push wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.
6. Raise canopy (J) to ceiling over threaded studs (O) and push firmly
to ceiling, making sure that no wires are pinched between canopy
and ceiling. Fasten with barrel knob (Q).
Note: Be sure both swivel notches are aligned in the same direction. For sloped
ceilings the notches should face towards the down side
7. Once the fixture is fastened to the ceiling, tighten the set screw (I) firmly with hex wrench provided. Only after the
set screw (I) is tight should you install the glass.
8. Refer to instructions for installing glass.
(Figure 5)
L Crossbar
M Stud (2)
N Lag Screw (4)
.
O Threaded Stud (2)
P Hex Nut (2)
Q Barrel Knob (2)
(Figure 5)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21041 Rev B
Page 4
Assembly & Installation Instructions A136
For Ellipse Pendants 13-7523 & 137523F Page 4 of 4
To Install Glass
Component Parts
R Socket (3)
S Glass (3)
T Retaining Ring (3)
U Socket Tool
1. Remove retaining rings (T) from sockets (S). Retaining rings
are shipped installed on product.
2. Slip glass (S) over socket (R).
3. Thread retaining ring (T) onto socket using socket tool
provided (U) until it rests on inside of glass (S). Do not over
tighten.
4. Install light bulbs and restore electricity at main breaker.
(Figure 6)
(Figure 6)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21041 Rev B
Loading...