Hubbardton Forge 137475 User Manual

Assembly & Installation Instructions A146

CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSONAL

(Figure 2)

(Figure 1)

Lyra Pendant 13-7470, 13-7470F, 137475 & 137475F Page 1 of 3

INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Prepare the Canopy (Figure 1)

Component Parts

A Jam Nut (2)
B Crossbar
C Threaded Nipple
D Canopy
E Canopy Ring

Caution: Be sure power is off at the main breaker box prior to installation.

1. Thread jam nuts (A) and crossbar (B) onto threaded nipple (C); leave parts loose.

2. Using two machine screws (not provided), temporarily fasten the crossbar (B) to

the electric box.

fixture, retain the existing screws for use with the new fixture.

3. Adjust the length of threaded nipp le (C) in crossbar (B) so that canopy ring (E)

will hold canopy (D) against the ceiling with no threads showing for best
appearance. When the correct adjustment is established, tighten jam nuts (A)
against crossbar (B) to hold the adjustment.

4. Remove the crossbar and stem from the electrical box and proceed with the

assembly instructions.

Note: A new electric box comes with screws. When replacing a

Complete Assembly and Install (Figures 2 & 3)

Component Parts

D Canopy
E Canopy Ring

Caution: Be sure power is off at the main breaker box prior to installation.

F Cano p y Pipe
G Plastic Sleeve

H Clutch
I Set Screw

J Fixture Pipe

1. Place canopy (D) over canopy pipe (F), followed by canopy

ring (E). Make sure smaller diameter side of canopy ring is
oriented up toward the canopy.

2. Thread wires from the fixture pipe (J) through the canopy

pipe (F).

3. Unscrew the clutch (H) from the canopy pipe (F); slide it

across the wires and onto the fixture pipe (J). Follow this
with the plastic clutch sleeve (G), oriented so the tapered end
of the clutch sleeve nests in the clutch (Figure 2).

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

21178 Rev C

(continued)

Assembly & Installation Instructions A146

(Figure 3)

(Figure 4)

Lyra Pendant 13-7470, 13-7470F, 137475 & 137475F Page 2 of 3

4. Slide the canopy pipe (F) as far as necessary to give you the total length of the fixture

which you desire. Be careful not to scratch the pipe surfaces and to pull excess wire up
through the canopy pipe (F). There must be a minimum 1-1/2" of inner pipe inside the outer
pipe. Hand-tighten the clutch to temporarily hold this adjustment. The clutch is not securely
fastened at this point; do not depend on it to hold the fixture.

Important: To ensure full connection strength, be sure the tapered end of the plastic clutch
sleeve is oriented toward the clutch when assembled and securely tighten set screw

(Figure 2).

5. Carefully slide canopy ring (E) and canopy (D) down over fixture pipe (J) unt il they rest on

the fixture.

6. Using two machine screws (not provided), fasten the crossbar to the electric box.

Note: A new electric box comes with screws. When replacing a fixture, retain the existing
screws for use with the new fixture.

7. Using suitable wire connectors (not provided), connect fixture wires to supply wires (white

to white supply, black to black supply). Run a pigtail lead from crossbar ground screw to
the junction box and connect all ground wires (bare copper or green to bare copper or
green). Push wires back into outlet box.

Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.

8. Slide fixture canopy (D) against ceiling, and secure with canopy ring (E).

9. Refer to instructions below to install glass & light bulb option purchased.

To Install Glass with G9 Option (Figure 4)

Component Parts

K Glass
L Socket
M Bulb (Included)
N Bulb Shi el d

P Washer (Only used on product 137475)

1. Slip glass (K) over socket (L).

2. Slip washer (P) over socket so it rests on glass (K). For product

137475 only.

3. Install light bulb (M). Be careful not to touch bulb with bare

hands; oil from the hands will dramatically reduce bulb life.

4. Thread bulb shield (N) onto socket (L) (be careful not to over

tighten). Future bulb changes may be accomplished by snapping
glass portion of barrier on and off rather than unthreading the
holder.

5. Restore electricity at main breaker.

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

21178 Rev C