Hubbardton Forge 136510 User Manual

Assembly & Installation Instructions A324

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

(Figure 2)

Corona Triple Pendant 13-6510 Page 1 of 3

To Assemble Canopy (Figure 1)

Component Parts

A Hex Nipple (3)
B Lock Washer (3)
C Canopy
D Canopy Pipe (3)

1. Carefully unpack canopy from carton.

2. Line up end of canopy pipe (D) with hole in canopy (C).

3. Place hex nipple (A) through lock washer (B), down through holes in

canopy and thread into canopy pipe. Tighten securely.

4. Repeat steps 2 and 3 for the remaining stems.

Stem Assembly (Figure 2)

Component Parts

E Fixture Pipe (3)
F Fixture Coupling (3)

1. Carefully thread fixture pipe (E), threaded end first, over fixture

wires.

2. Apply a drop of the supplied thread locking compound to the

internal threads of fixture coupling (F) and screw stem into fixture,
being careful not to twist or pinch the wires.

Note: Application of the thread locking compound is necessary to
prevent the stem from loosening during regular maintenance and
cleaning of the fixture. Be certain to apply the compound.

3. Complete steps 1 & 2 for remaining fixture pipes.

4. See instructions below to complete the installation.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735 28099 Rev A

(continued)

Assembly & Installation Instructions A324

(Figure 3)

(Figure 4)

Corona Triple Pendant 13-6510 Page 2 of 3

To Assemble and Install Fixture (Figures 3 & 4)

Components

D Canopy Pipe (3)
E Fixture Pipe (3)
G Crossbar
H Threaded Studs (2)
I Canopy
J Knurl Ball (2)
K Canopy Cover

1. Carefully unpack fixture from carton.

2. Thread the wires from the fixture pipe (E) into and through the

canopy pipe (D) up through the canopy (I).

3. Unscrew clutch (O) from canopy pipe (D), slide it across the wires

and onto the fixture pipe (E). Follow this with the clutch sleeve
(N), so it nests in clutch (O).

4. Slide the fixture pipe (E) up into canopy pipe (D) as far necessary

to give you the total length of the fixture which you desire. Be
careful not to scratch the pipe surfaces and to pull excess wire up
through the canopy (I). There must be a minimum 1-1/2" of
inner pipe inside the outer pipe. Hand-tighten the clutch to
temporarily hold this adjustment. At this point the adjustment is

not securely fastened; do not depend on it to hold the fixture.

Important: To ensure full connection strength, be sure the
tapered end of the plastic clutch sleeve is oriented toward the
clutch when assembled and securely tighten set screw (Figure 3).

5. Thread studs (H) through appropriate holes in the crossbar (G) to

match hole centers in canopy (I).

6. Using two machine screws (not provided), fasten the crossbar (G)

to the electric box using outer oval slots to orient fixture to desired
hanging position.

Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.

7. Slide fixture canopy (I) with fixture attached, over threaded studs

(H) and push firmly to ceiling making sure no wires are pinched
between fixture canopy and ceiling. Fasten with knurled balls (J).
Be sure studs (H) are fully seated in knurled balls (J).

8. Using suitable wire connectors (not provided) connect fixture

wires to supply (white to white and black to black). Run a pigtail
lead from crossbar ground screw (P) and cupped washer (Q) to the
junction box and connect all ground wires (bare copper or green to
bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.

9. Check fixtures for height and level.

10. Once the fixture is fastened to the ceiling, tighten the set screws (M) on the clutches firmly with hex wrench

provided. Only after the set screws (M) are tight should you install the glass.

11. Repeat for all three fixtures (continued)

L Lock Up
M Set Screw (3)
N Clutch Sleeve (3)
O Clutch (3)
P Ground Screw
Q Cupped Washer
R Canopy Nipple

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735 28099 Rev A