Hubbardton Forge 136500 User Manual
Assembly & Installation Instructions A314
Corona Adjustable Pendant 13-6500 Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Stem Assembly (Figure 1)
Component Parts
A Fixture Pipe
B Fixture Coupling
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipe (A), threaded end first, over fixture wires and support cable.
3. Apply a drop of the supplied thread locking compound to the internal threads of fixture
coupling (B) and screw stem into fixture, being careful not to twist or pinch the wires.
Note: Application of the thread locking compound is necessary to prevent the stem from
loosening during regular maintenance and cleaning of the fixture. Be certain to apply the
compound.
4. See instructions below to complete the installation.
(Figure 1)
Prepare the Canopy
Component Parts
C Crossbar
D Jam Nut
E Threaded Nipple
F Canopy
G Canopy Ring
Caution: Be sure power is off at the main breaker box prior to installation.
(Figure 2)
1. Thread the jam nut (D) and crossbar (C) onto threaded nipple (E); leave both parts
loose.
2. Using two machine screws (not provided), temporarily fasten the crossbar (C) to the
electric box.
retain the existing screws for use with the new fixture.
Note: A new electric box comes with screws. When replacing a fixture,
3. Adjust the length of threaded nipple (E) in crossbar (C) so that canopy ring (G) will
hold canopy (F) against the ceiling with no threads showing for best appearance.
When the correct adjustment is established, tighten jam nut (D) against crossbar (C)
to hold the adjustment.
4. Remove the crossbar and stem from the electrical box and proceed with the assembly
instructions.
(Figure 2)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27635
Assembly & Installation Instructions A314
Corona Adjustable Pendant 13-6500 Page 2 of 3
Complete Assembly & Install Fixture
Component Parts
A Fixture Pipe G Canopy Ring
C Crossbar H Plastic Sleeve
D Jam Nut I Clutch
E Threaded Nipple J Set Screw
F Canopy
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Place canopy (F) over canopy pipe, followed by canopy ring (G).
Make sure smaller diameter side of canopy ring is oriented up toward the canopy.
2. Unscrew the clutch (I) from the canopy pipe; slide it across the wires and
onto the fixture pipe (A). Follow this with the plastic clutch sleeve (H),
oriented so the tapered end of the clutch sleeve nests in the clutch. (Figure
3).
3. Slide the canopy pipe as far as necessary to give you the total length of the
fixture which you desire. Be careful not to scratch the pipe surfaces and to
pull excess wire up through the canopy pipe. There must be a minimum 11/2" of inner pipe inside the outer pipe. Hand-tighten the clutch to
temporarily hold this adjustment. The clutch is not securely fastened at this
point; do not depend on it to hold the fixture.
connection strength, be sure the tapered end of the plastic clutch sleeve
(H) is oriented toward the clutch (I) when assembled and securely tighten
set screw (J) (Figure 3).
4. Carefully slide canopy ring (G) and canopy (F) down over fixture pipe (A)
until they rest on the fixture.
5. Using two machine screws (not provided), fasten the crossbar to the
electric box.
a fixture, retain the existing screws for use with the new fixture.
Note: A new electric box comes with screws. When replacing
6. Using suitable wire connectors (not provided), connect fixture wires to
supply wires (white to white supply, black to black supply, and bare
copper to bare copper or green supply). Run a pigtail lead from crossbar
(C) green ground screw to the junction box and connect all ground wires
(bare copper or green to bare copper or green). Push wires back into outlet
box.
Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.
7. Slide fixture canopy (F) against ceiling, and secure with canopy ring (G).
Once the fixture is fastened to the ceiling, tighten the set screw (J) on the
clutch (I) firmly with hex wrench provided. Only after the set screw is tight
should you install the glass.
(Figures 3 & 4)
(Figure 3)
Important: To ensure full
(Figure 4)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27635
Loading...