
Installation Instructions A243
For Axis Pendants 13-6405 & 13-6405F Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
After installation extra hardware and accessories are possible; our kits are used on multiple products and options.
To Assemble Fixture (Figures 1 & 2)
Component Parts
A 8-32 Screw
B Canopy Pipe Assembly
C Cable Gripper Assembly
D Canopy
E Aircraft Cable
F Cable Gripper
G Upper Assembly
Caution: Be sure power is off at the main breaker box prior to installation.
1. Remove 8-32 screw (A) and save for later use.
(Figure 1)
2. Lift cable gripper assembly (C) from canopy pipe assembly
(B) (Figure 2).
3. Slip wires and aircraft cable (E) through hole in the bottom of
canopy (D).
4. Slip canopy (D) onto upper assembly (G) and allow it to rest
on top of fixture.
5. Thread the wires and aircraft cable (E) from the upper
assembly (G) into and through the canopy pipe assembly (B).
6. Lower canopy pipe assembly (B) into upper assembly (G)
until it bottoms out.
7. Push the aircraft cable (E) through the bottom of the cable
gripper (F). Do not pull the aircraft cable completely through
at this point.
8. Slip canopy pipe assembly (B) up to desired height while
pulling the aircraft cable (E) through the cable gripper (F).
Measurement equals from ceiling to desired location of
fixture bottom subtract 6 3/16”. (If total length equals 40”
subtract 6 3/16” from 40” and this is the measurement to set
the canopy pipe assembly to).
9. Attach cable gripper assembly (C) to canopy pipe assembly
(B) using 8-32 screw (A).
10. Pull excess aircraft cable (E) through cable gripper (F) until
snug.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 2)
(continued)
24571

Installation Instructions A243
For Axis Pendants 13-6405 & 13-6405F Page 2 of 3
Install Fixture to Ceiling (Figure 3)
Component Parts
B Canopy Pipe Assembly
D Canopy
H Crossbar
I Ground Screw
J Threaded Studs (2)
K Barrel Knobs (2)
1. Using two machine screws (not provided), fasten the crossbar (H) to the
electric box using oval slots to orient fixture to desired hanging
position. We've supplied lag screws with your fixture; however,
different materials and/or construction methods may require different
fasteners. If in doubt, contact a qualified electrician.
Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.
2. Thread studs (J) through appropriate holes in the crossbar (H) to match
hole centers on canopy (D).
3. Using suitable wire connectors (not provided) connect fixture wires to
supply (white to white or ribbed and black to black or smooth).
4. Lift canopy (D) and connect all ground wires to green ground
screw (I).
5. Slide canopy (D) over threaded studs (J) and push firmly to ceiling,
making sure that no wires are pinched between fixture canopy and
ceiling. Fasten with barrel knobs (K). Be sure studs are fully seated in the
barrel knobs.
6. Refer instructions following to install bulb and glass.
(Figure 3)
To Install Glass in Bottom Assembly
Component Parts
L Lower Assembly
M Center Diffuser
N Bottom Diffuser
O Outer Acrylic Ring
(Figure 4)
1. Install bottom diffuser (N) and outer acrylic ring (O) into lower
assembly (L).
2. Install center diffuser (M) so it sits in the center of the lower
assembly (L).
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 4)
(continued)
24571