Assembly & Installation Instructions A255
For Ondrian Triple Canopy Four-Light Pendant 13-6315 Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Assemble Canopy (Figure 1)
Component Parts
A Hex Nipple (3)
B Lock Washer (3)
C Canopy
D Canopy Pipe (3)
1. Carefully unpack canopy from carton.
2. Line up end of canopy pipe (D) with hole in canopy (C).
3. Place hex nipple (A) through lock washer (B), down through holes in canopy and
thread into canopy pipe. Tighten securely.
4. Repeat steps 2 and 3 for the remaining stems.
Stem Assembly
Component Parts
E Fixture Pipe (3)
F Fixture Coupling (3)
(Figure 1)
1. Carefully thread fixture pipe (E), threaded end first, over fixture
wires.
2. Apply a drop of the supplied thread locking compound to the
internal threads of fixture coupling (F) and screw stem into
fixture, being careful not to twist or pinch the wires.
Note: Application of the thread locking compound is necessary to
prevent the stem from loosening during regular maintenance and
cleaning of the fixture. Be certain to apply the compound.
3. See instructions below to complete the installation.
(Figure 1)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 2)
(continued)
24645
Assembly & Installation Instructions A255
For Ondrian Triple Canopy Four-Light Pendant 13-6315 Page 2 of 3
To Assemble and Install Fixture (Figures 3 & 4)
Components
D Canopy Pipe (3)
E Fixture Pipe (3)
G Crossbar
H Threaded Studs (2)
I Canopy
J Knurl Ball (2)
K Canopy Cover
1. Carefully unpack fixture from carton.
2. Thread the wires from the fixture pipe (E) into and through the canopy
3. Unscrew the clutch (O) from the canopy pipe (D) slide it across the
4. Slide the fixture pipe (E) up into canopy pipe (D) as far necessary to
5. Thread studs (H) through appropriate holes in the crossbar (G) to match
6. Using two machine screws (not provided), fasten the crossbar (G) to the
7. Slide fixture canopy (I) with fixture attached, over threaded studs (H)
8. Using suitable wire connectors (not provided) connect fixture wires to
9. Check fixtures for height and level.
10. Once the fixtures are fastened to the ceiling, tighten the set screws (M)
L Lock Up
M Set Screw (3)
N Clutch Sleeve (3)
O Clutch (3)
P Ground Screw
Q Canopy Nipple
pipe (D) up through the canopy (I).
wires and onto the fixture pipe (E). Follow this with the clutch sleeve
(N), so it nests in the clutch (O).
give you the total length of the fixture which you desire. Be careful not
to scratch the pipe surfaces and to pull excess wire up through the
canopy (I). There must be a minimum 1-1/2" of inner pipe inside the
outer pipe. Hand-tighten the clutch to temporarily hold this adjustment.
At this point the adjustment is not securely fastened; do not depend
on it to hold the fixture.
Important: To ensure full connection strength, be sure the tapered
end of the plastic clutch sleeve is oriented toward the clutch when
assembled and securely tighten set screw
(Figure 3).
hole centers in canopy (I).
electric box using outer oval slots to orient fixture to desired hanging
position.
Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.
and push firmly to ceiling making sure no wires are pinched between
fixture canopy and ceiling. Fasten with knurled balls (J). Be sure studs
(H) are fully seated in knurled balls (J).
supply (white to white and black to black).
Run a pigtail lead from
crossbar ground screw (P) to the junction box and connect all ground
wires (bare copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.
on the clutches firmly with hex wrench provided. Only after the set
screws (M) are tight should you install the glass. Repeat for all three
fixtures.
(Figure 3)
(Figure 4)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24645
Assembly & Installation Instructions A255
For Ondrian Triple Canopy Four-Light Pendant 13-6315 Page 3 of 3
11. Thread canopy nipple (Q) in to threaded hole directly in center of canopy (I).
12. Install canopy cover (K) on canopy nipple (Q).
13. Thread lock up (L) on to canopy nipple (Q). Tighten against canopy cover (K) until snug.
14. Refer to instructions below to install glass.
To Install Glass and Bulb
Component Parts
R Socket (12)
S Bulb (Included)(12)
T Glass (12)
U Spacer (12)
V Retaining Ring (12)
W Socket Tool
1. Remove retaining rings (V) and spacers (U) from sockets (R). Parts are shipped
installed on sockets. Save for later use.
2. Install light bulbs (S). Be careful not to touch bulb with bare hands; oil from the
hands will dramatically reduce bulb life.
3. Slip glass (T) over socket (R).
4. Slip spacer (U) over socket (R) so it rests on glass (T).
5. Thread retaining ring (V) onto socket (R) using provided socket tool (W). Be careful
not to over tighten.
6. Repeat steps 3 thru 5 for all arms.
7. Restore electricity at main breaker.
(Figure 5)
(Figure 5)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this
product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24645
Loading...