Hubbardton Forge 136305 User Manual

Assembly & Installation Instructions A206

Ondrian Pendant 13-6305 & 13-6305F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Complete Assembly (Figures 1 & 2)

Component Parts

A Hex Head Nipple (2)
B Crossbar
C Threaded Stud (2)
D Canopy
E Barrel Knobs (2)
F Canopy Pipe (2)
G Plastic Clutch Sleeve (2)

Caution: Be sure power is off at the main breaker box prior to
installation.

1. Unscrew the clutch (H) from the canopy pipe (F); slide it

across the wires and onto the fixture pipe (K). Follow this with
the plastic clutch sleeve (G), oriented so the tapered end of the
clutch sleeve nests in the clutch.

2. Slide the canopy pipes (F) as far as necessary to give you the

total length of the fixture which you desire. Be careful not to
scratch the pipe surfaces and to pull excess wire up through
the canopy pipe (F). Screw clutch (H) onto canopy pipe (F).
There must be a minimum 1-1/2" of inner pipe inside the outer
pipe. Hand-tighten the clutch to temporarily hold this
adjustment. The clutch is not securely fastened at this point;
do not depend on it to hold the fixture.

full connection strength, be sure the tapered end of the plastic
clutch sleeve is oriented toward the clutch when assembled and
securely tighten set screw (Figure 2).

3. Slide canopy (D) over canopy pipes (F) being careful not to scratch

finish. Slide down until the canopy rests against
clutch (H).

4. Thread studs (C) through appropriate holes in crossbar (B)

to match holes in canopy (D).

5. Attach crossbar (B) to both canopy pipes (F) using hex

head nipple (A) and lock washer (J).

6. Using two machine screws (not provided), fasten the

crossbar (B) to the electric box.

comes with screws. When replacing a fixture, retain the
existing screws for use with the new fixture.

Note: A new electric box

7. Using suitable wire connectors (not provided) connect

fixture wires to supply (white to white and black to black).
Connect all ground wires to green ground screw (L) and
cupped washer (M).

twisted on securely, and no bare wire is exposed.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

Caution: Make sure wire connectors are

H Clutch (2)
I Set Screw (2)
J Lock Washer (2)
K Fixture Pipe (2)
L Ground Screw
M Cupped Washer

Important: To ensure

(Figure 1)

(Figure 2)

(continued)

22763 Rev B

Assembly & Installation Instructions A206

Ondrian Pendant 13-6305 & 13-6305F Page 2 of 2

8. Slide canopy (D) over threaded studs (C) and push firmly to ceiling, making sure that no wires are pinched between

fixture canopy and ceiling. Fasten with barrel knobs (E). Be sure studs are fully seated in the barrel knobs.

9. Once the fixture is fastened to the ceiling, tighten the set screw (I) in clutch (H) firmly with hex wrench provided.

Only after the set screw (I) is tight should you install the lower assembly.

10. Refer instructions below and install glass/shade for option that was purchased.

To Install Glass with G9 Option

Component Parts

N Socket (6)
O Bulb (Included) (6)
P Glass (6)
Q Spacer (6)
R Retaining Ring (6)
S Socket Tool

1. Remove retaining ring (R) and spacer (Q) from socket (N). Retaining Rings and

spacers are shipped installed.

2. Install light bulb (O). Be careful not to touch bulb with bare hands; oil from the

hands will dramatically reduce bulb life.

3. Slip glass (P) over socket (N).

4. Slip spacer (Q) over socket (N) so it rests on glass (P).

5. Thread retaining ring (R) onto socket (N) using provided socket tool (S). Be careful

not to over tighten.

6. Restore electricity at main breaker.

To Install Glass with GU24 Option (Figure 4)

(Figure 3)

(Figure 3)

Component Parts

N Socket (6)
O Bulb (Included) (6)
P Glass (6)
R Retaining Ring (6)
S Socket Tool
T Washer

1. Remove retaining ring (R) from socket (N). Retaining Rings are shipped installed.

2. Slip glass (P) over socket (N).

3. Slip washer (T) onto socket (N) so it rests on the bottom of glass (P).

4. Thread retaining ring (R) onto socket (N) using provided socket tool (S) provided

until it rests on the washer (T). Do not over tighten.

5. Install light bulb (O).

(Figure 4)

6. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

22763 Rev B