Page 1
Assembly & Installation Instructions A263
Staccato Pendants 13-4910 & 13-4915 Page 1 of 4
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Attach Fixture Pipes (Figure 1)
Component Parts
A Fixture Pipe (2)
B Fixture Coupling (2)
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipes (A), threaded end
first, over fixture wires.
3. Apply a drop of the supplied thread locking
compound to the internal threads of the fixture
couplings (B) and screw fixture pipes (A) into
fixture, being careful not to twist the wires.
Note: Application of the thread locking compound
is necessary to prevent the stem from loosening
during regular maintenance and cleaning of the
fixture. Be certain to apply the compound.
(Figure 1)
(Figure 1)
4. See instructions below to complete the installation.
Assemble Canopy Pipes to Ceiling Bracket
Component Parts
C Hex Nipple (2)
D Lock Washer (2)
E Ceiling Bracket
F Canopy Pipes (2)
(Figure 2)
1. Insert threaded end of hex nipple (C) down through
lock washer (D), ceiling bracket (E) and into swivel at
the end of canopy pipe (F). Note: Ceiling bracket
should be oriented with the threaded studs point down.
2. Tighten securely being sure the notches in the swivels
are aligned.
Note: If installing on a sloped ceiling, make certain that
the notches in the swivel portion of the stems are
oriented toward the lower side of the slope.
Illustration may not match every style.
(Figure 2)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
21041 Rev A
Page 2
Assembly & Installation Instructions A263
Staccato Pendants 13-4910 & 13-4915 Page 2 of 4
Complete Fixture Assembly
Component Parts
A Fixture Pipe (2)
C Hex Nipple
F Canopy Pipe (2)
G Clutch (2)
Caution: Be sure power is off at the main breaker box prior to
installation.
(Figures 3 & 4)
H Canopy
I Plastic Clutch Sleeve (2)
J Set Screw (2)
1. Thread wires from the fixture pipes (A)
through canopy (H). Slide canopy (H)
down fixture pipes (A) until it rests on
top of fixture.
2. Thread the wires from the fixture pipe
(A) into and through the canopy pipe (F)
up through the hex nipple (C).
3. Unscrew the clutch (G) from the canopy
pipe (F); slide it across the wires and
onto the fixture pipe (A). Follow this
with the plastic clutch sleeve (I),
oriented so the tapered end of the clutch
sleeve nests in the clutch. Repeat for
both pipes. (Figure 3).
4. Slide the canopy pipe (F) as far as
necessary to give you the total length of
the fixture which you desire. Be careful
not to scratch the pipe surfaces and to
pull excess wire up through the canopy
pipe (F). Screw clutch (G) onto canopy
pipe (F). There must be a minimum 11/2" of inner pipe inside the outer pipe.
Hand-tighten the clutch to temporarily
hold this adjustment. The clutch is not
securely fastened at this point; do not
depend on it to hold the fixture. Repeat
for both pipes.
Important: To ensure full connection
strength, be sure the tapered end of the
plastic clutch sleeve is oriented toward
the clutch when assembled and
securely tighten set screw
(Figure 3).
5. Continue with Ceiling Installation.
(Figure 3)
(Figure 4)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
Illustration may not match every style.
(continued)
21041 Rev A
Page 3
Assembly & Installation Instructions A263
Staccato Pendants 13-4910 & 13-4915 Page 3 of 4
Install to Ceiling
Component Part
E Ceiling Bracket
H Canopy
J Set Screw (2)
K Threaded Stud (2)
1. Using wood screws (L) attach ceiling bracket
(E) to a structural member in the ceiling,
centering the bracket over the outlet box.
We've supplied wood screws with your
fixture; however, different materials and/or
construction methods may require different
fasteners. If in doubt, contact a qualified
electrician. Do not attach ceiling bracket
directly to outlet box
2. Using suitable wire connectors (not provided)
connect fixture wires to supply (white to white
and black to black).
3. Using cupped washer (O) and hex nut (M) run
a pigtail lead from ceiling bracket to the
junction box. Raise canopy (H) and connect
all ground wires (bare copper or green to bare
copper or green). Push wires back into outlet
Caution: Make sure wire connectors are
box.
twisted on securely, and no bare wire is
exposed.
4. Slide fixture canopy (H) over threaded studs
(K) and push firmly to ceiling, making sure
that no wires are pinched between fixture
canopy and ceiling. Fasten with barrel knobs
(N). Be sure studs (K) are fully seated in
barrel knobs (N).
5. Once the fixture is fastened to the ceiling,
tighten the set screws (J) firmly with hex
wrench provided. Only after the set screws (J)
are tight should you install the glass. Be sure
to tighten set screws in both clutches.
6. Refer to instructions following to install glass.
(Figure 5)
L #10 Wood Screws (8)
M Hex Nut
N Barrel Knobs (2)
O Cupped Washer
.
(Figure 5)
Illustration may not match every style.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
24825
Page 4
Assembly & Installation Instructions A263
Staccato Pendants 13-4910 & 13-4915 Page 4 of 4
Install Bulb and Glass
Component Parts
P Socket (10)
Q Bulb (Included)(10)
R Glass (10)
S Retaining Ring (10)
T Retaining Ring Tool
1. Remove retaining rings (S) from sockets (P) and set aside for later use.
Retaining rings are shipped installed on the sockets.
2. Install light bulb (Q). Be careful not to touch bulb with bare hands; oil from the
hands will dramatically reduce bulb life.
3. Slip glass (R) over socket (P) and thread retaining ring (S) onto socket (P) using
provided retaining ring tool (T). Repeat for all ten sockets.
4. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(Figure 6)
(Figure 6)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24825
Loading...