Page 1
Assembly & Installation Instructions A250
Staccato Six Light Pendant 13-4901 Page 1 of 4
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Attach Fixture Pipes (Figure 1)
Component Parts
A Fixture Pipe (2)
B Fixture Coupling (2)
1. Carefully unpack the fixture from the carton.
2. Carefully thread fixture pipes (A), threaded end first,
over fixture wires.
3. Apply a drop of the supplied thread locking
compound to the internal threads of the fixture
couplings (B) and screw fixture pipes (A) into
fixture, being careful not to twist the wires.
Note: Application of the thread locking compound is
necessary to prevent the stem from loosening during
regular maintenance and cleaning of the fixture. Be
certain to apply the compound.
4. See instructions below to complete the installation.
(Figure 1)
Assemble Canopy Pipes to Ceiling Bracket
Component Parts
C Hex Nipple (2)
D Lock Washer (2)
E Ceiling Bracket
F Canopy Pipes (2)
(Figure 2)
1. Insert threaded end of hex nipple (C) down through lock
washer (D), ceiling bracket (E) and into swivel at the end of
canopy pipe (F).
2. Tighten securely being sure the notches in the swivels are
aligned.
Note: If installing on a sloped ceiling, make certain that the
notches in the swivel portion of the stems are oriented toward
the lower side of the slope.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
21041 Rev A
(Figure 2)
(continued)
Page 2
Assembly & Installation Instructions A250
Staccato Six Light Pendant 13-4901 Page 2 of 4
Complete Fixture Assembly
Component Parts
A Fixture Pipe (2)
C Hex Nipple
F Canopy Pipe (2)
G Clutch (2)
Caution: Be sure power is off at the main breaker box prior to
installation.
(Figures 3 & 4)
H Canopy
I Plastic Clutch Sleeve (2)
J Set Screw (2)
1. Thread wires from the fixture pipes (A) through canopy (H).
Slide canopy (H) down fixture pipes (A) until it rests on top
of fixture.
2. Thread the wires from the fixture pipe (A) into and through
the canopy pipe (F) up through the hex nipple (C).
3. Unscrew the clutch (G) from the canopy pipe (F); slide it
across the wires and onto the fixture pipe (A). Follow this
with the plastic clutch sleeve (I), oriented so the tapered end
of the clutch sleeve nests in the clutch. Repeat for both pipes.
(Figure 3).
4. Slide the canopy pipe (F) as far as necessary to give you the
total length of the fixture which you desire. Be careful not to
scratch the pipe surfaces and to pull excess wire up through
the canopy pipe (F). Screw clutch (G) onto canopy pipe (F).
There must be a minimum 1-1/2" of inner pipe inside the
outer pipe. Hand-tighten the clutch to temporarily hold this
adjustment. The clutch is not securely fastened at this point;
do not depend on it to hold the fixture. Repeat for both pipes.
Important: To ensure full connection strength, be sure the
tapered end of the plastic clutch sleeve is oriented toward the
clutch when assembled and securely tighten set screw
(Figure 3).
5. Continue with Ceiling Installation.
(Figure 3)
(Figure 4)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
21041 Rev A
Page 3
Assembly & Installation Instructions A250
Staccato Six Light Pendant 13-4901 Page 3 of 4
Install to Ceiling
Component Part
E Ceiling Bracket
H Canopy
J Set Screw (2)
K Crossbar
1. Using two machine screws (not provided)
fasten cross bar (K) to the electric box using
outer oval holes to orient fixture to desired
hanging position.
Note: A new electric box comes with screws.
When replacing an existing fixture, retain the
screws for use with the new fixture.
2. Raise fixture to ceiling aligning center holes in
ceiling bracket (E) with threaded holes in
crossbar (K) install two 8-32 x 3/8” screws
(M).
3. Using suitable wire connectors (not provided)
connect fixture wires to supply (white to white
and black to black).
4. Run a pigtail lead from crossbar ground screw
(N) to the junction box. Raise canopy and
connect all ground wires (bare copper or green
to bare copper or green).Push wires back into
outlet box.
connectors are twisted on securely, and no
bare wire is exposed.
5. Slide fixture canopy (G) over threaded studs
(L) and push firmly to ceiling, making sure
that no wires are pinched between fixture
canopy and ceiling. Fasten with barrel knobs
(O). Be sure studs (L) are fully seated in barrel
knobs (O).
6. Once the fixture is fastened to the ceiling,
tighten the set screw (J) firmly with hex
wrench provided. Only after the set screw (J)
is tight should you install the glass. Be sure to
tighten set screws in both clutches.
7. Refer to instructions following to install glass.
(Figure 5)
L Threaded Stud (2)
M 8-32 X 3/8” Screw (2)
N Ground Screw
O Threaded Knobs
Caution: Make sure wire
(Figure 5)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
21041 Rev A
(continued)
Page 4
Assembly & Installation Instructions A250
Staccato Six Light Pendant 13-4901 Page 4 of 4
Install Bulb and Glass
Component Parts
P Socket (6)
Q Bulb (Included)(6)
R Glass (6)
S Retaining Ring (6)
T Retaining Ring Tool
1. Remove retaining rings (S) from sockets (P) and set aside for later use.
Retaining rings are shipped installed on the sockets.
2. Install light bulb (Q). Be careful not to touch bulb with bare hands; oil from the
hands will dramatically reduce bulb life.
3. Slip glass (R) over socket (P) and thread retaining ring (S) onto socket (P) using
provided retaining ring tool (T). Repeat for all six sockets.
4. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(Figure 6)
(Figure 6)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
21041 Rev A
Loading...