Assembly & Installation Instructions A249
For Adjustable Mobius Shade Pendant 13-4503 Page 1 of 7
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Prepare the Canopy (Figure 1)
Component Parts
A Jam Nut
B Crossbar
C Threaded Nipple
D Canopy
E Canopy Ring
Caution: Be sure power is off at the main breaker box prior to installation.
1. Thread jam nut (A) and crossbar (B) onto threaded nipple (C); leave both parts
loose.
2. Using two machine screws (not provided), temporarily fasten the crossbar (B) to
the electric box.
fixture, retain the existing screws for use with the new fixture.
3. Adjust the length of threaded nipple (C) in crossbar (B) so that canopy ring (E)
will hold canopy (D) against the ceiling with no threads showing for best
appearance. When the correct adjustment is established, tighten jam nut (A)
against crossbar (B) to hold the adjustment.
4. Remove the crossbar and stem from the electrical box and proceed with the
assembly instructions.
Complete Assembly & Install Fixture
Note: A new electric box comes with screws. When replacing a
(Figures 2 & 3)
(Figure 1)
Component Parts
D Canopy
E Canopy Ring
F Canopy Pipe
G Fixture Pipe
H Plastic Sleeve
I Clutch
J Set Screw
K Ground Screw
L Shade Spider
M Retaining Ring
N Socket
Caution: Be sure power is off at the main breaker box prior to installation.
(Figure 2)
1. Place canopy (D) over canopy pipe (F), followed by canopy ring (E). Make sure smaller diameter side of canopy
ring is oriented up toward the canopy.
2. Thread wires from the fixture pipe (G) through the canopy pipe (F).
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24619
Assembly & Installation Instructions A249
For Adjustable Mobius Shade Pendant 13-4503 Page 2 of 7
3. Unscrew the clutch (I) from the canopy pipe (F); slide it across the wires and onto the
fixture pipe (G). Follow this with the plastic clutch sleeve (H), oriented so the tapered
end of the clutch sleeve nests in the clutch. (Figure 2).
4. Slide the canopy pipe (F) as far as necessary to give you the total length of the fixture
which you desire. Be careful not to scratch the pipe surfaces and to pull excess wire up
through the canopy pipe (F). There must be a minimum 1-1/2" of inner pipe inside the
outer pipe. Hand-tighten the clutch to temporarily hold this adjustment. The clutch is
not securely fastened at this point; do not depend on it to hold the fixture.
Important: To ensure full connection strength, be sure the tapered end of the plastic
clutch sleeve is oriented toward the clutch when assembled and securely tighten set
screw (Figure 3).
5. Carefully slide canopy ring (E) and canopy (D) down over fixture pipe (G) until they
rest on the fixture.
6. Using two machine screws (not provided), fasten the crossbar to the electric box.
Note: A new electric box comes with screws. When replacing a fixture, retain the
existing screws for use with the new fixture.
7. Using suitable wire connectors (not provided), connect fixture wires to supply wires
(white to white supply, black to black supply). Run a pigtail lead from crossbar ground
screw (A) to the junction box and connect all ground wires (bare copper or green to
bare copper or green). Connect all ground wires to green ground screw (L). Push
wires back into outlet box.
securely, and no bare wire is exposed.
8. Slide fixture canopy (D) against ceiling, and secure with canopy ring (E).
9. Once the fixture is fastened to the ceiling, tighten the set screw (J) firmly with hex
wrench provided.
10. Remove retaining ring (M) from socket (N). Slip shade spider (L) from socket and
store both parts for later use. Retaining ring is shipped installed on socket.
11. Refer to instructions below to install shade and light bulb.
Install Shade
(Figure 4)
Caution: Make sure wire connectors are twisted on
(Figure 3)
Component Parts
M Retaining Ring
N Socket
O Shade Assembly
1. Refer to instructions beginning on next page to assemble the shade.
2. Slip shade assembly (O) over socket (N).
3. Thread retaining ring (M) onto socket (N).
4. Install light bulb. (Not Included)
5. Restore electricity at the main breaker.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 4)
(continued)
24619
Assembly & Installation Instructions A249
For Adjustable Mobius Shade Pendant 13-4503 Page 3 of 7
To see a video on how to assemble the Mobius shade, go to:
http://www.youtube.com/user/HubbardtonForge?v=EQzAHb_Ab2M
Assemble Shade
Component Parts
L Shade Spider (1)
P Flat Shade Panel (2)
Q Bracket with Studs (4)
R Knurled Balls (8)
Step 1 Identify all parts needed. Lay shade panels on a clean, flat surface as shown in illustration with “C” and “L”
cutouts oriented correctly.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
Flat Shade Panel (2)
(continued)
24619
Loading...