Hubbardton Forge 133255 User Manual

Page 1
Assembly & Installation Instructions A166
For Vortis Pendant 13-3255 Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Prepare the Canopy (Figure 1)
Component Parts
A Jam Nut (2) B Crossbar C Threaded Nipple D Canopy E Canopy Ring F Coupling G Canopy Pipe
Caution: Be sure power is off at the main breaker box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Thread Jam Nuts (A) and Crossbar (B) onto threaded nipple (C) leave parts
loose.
3. Using two machine screws (not provided), temporarily fasten the crossbar (B) to
the electric box.
Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new fixture.
4. Adjust the length of Threaded Nipple (C) in crossbar (B) so that Canopy Ring (E)
will hold Canopy (D) against the ceiling with no threads showing for best appearance. When the correct adjustment is established, tighten Jam Nuts (A) against crossbar (B) to hold the adjustment.
5. Remove the crossbar and stem from the electrical box and proceed with the
assembly instructions.
(Figure 1)
To Complete Assembly & Install
Component Parts
A Jam Nut (2) B Crossbar C Threaded Nipple D Canopy E Canopy Ring
G Canopy Pipe
Caution: Be sure power is off at the main breaker box prior to installation.
(Figures 2 & 3)
H Fixture Pipe I Plastic Clutch Sleeve J Clutch K Set Screw U Fixture Coupling
1. Thread crossbar (B) onto threaded nipple (C) until tight against jam nuts (A).
2. Carefully thread fixture pipe (H) over fixture wires.
Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 2)
(continued)
21319 Rev B
Page 2
Assembly & Installation Instructions A166
For Vortis Pendant 13-3255 Page 2 of 3
3. Apply a drop of the supplied thread locking compound to the internal threads of
fixture coupling (U) and screw fixture pipe (H) into fixture, being careful not to twist or pinch the wires.
Note: Application of the thread locking compound is necessary to prevent the stem from loosening during regular maintenance and cleaning of the fixture. Be certain to apply the compound.
4. Unscrew the clutch (J) from the fixture pipe (H); slide it across the wires and onto the
canopy pipe (G). Follow this with the plastic clutch sleeve (I), oriented so the tapered end of the clutch sleeve nests in the clutch (Figure 2).
5. Thread wires from the fixture pipe (H) through the canopy pipe (G).
6. Slide the canopy pipe (G) as far as necessary to give you the total length of the
fixture which you desire. Be careful not to scratch the pipe surfaces and to pull excess wire up through the canopy pipe (G). There must be a minimum 1-1/2" of inner pipe inside the outer pipe. Screw clutch (J) onto canopy pipe and hand-tighten the clutch to temporarily hold this adjustment. The clutch is not securely fastened at this point; do not depend on it to hold the fixture.
Important: To ensure full connection strength, be sure the tapered end of the plastic clutch sleeve is oriented toward the clutch when assembled and securely tighten set screw (Figure 2).
7. Using two machine screws (not provided), fasten the crossbar to the electric box.
Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new fixture.
8. Using suitable wire connectors (not provided), connect fixture wires to supply wires
(white to white or ribbed side of the fixture cord, black to black or smooth side, and bare copper to bare copper or green supply). Push wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.
9. Slide fixture canopy (D) against ceiling, and secure with canopy ring (E).
10. Once the fixture is fastened to the ceiling, tighten the set screw (K) in clutch (J)
firmly with hex wrench provided. Only after the set screw (K) is tight should you install the glass.
11. Refer to instructions below to install bulb and glass.
(Figure 3)
Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
21319 Rev B
Page 3
Assembly & Installation Instructions A166
For Vortis Pendant 13-3255 Page 3 of 3
To Install Bulb
Component Parts
L Bulb Shield M Bulb N Socket
1. Install light bulb (M). Be careful not to
touch bulb with bare hands; oil from the hands will dramatically reduce bulb life.
2. Thread bulb shield (L) onto socket (N) (be
careful not to over tighten). Future bulb changes may be accomplished by snapping glass portion of shield on and off rather than unthreading the holder.
(Figure 4)
To Install Glass
Component Parts
O Fixture Assembly P Fixture slot Q Glass R Retainer Tab S Glass Retainer T Tensioning Screw
(Figure 5)
(Figure 4)
1. Remove glass retainer (S) from bottom of fixture by
removing tensioning screw (T) and turning the glass retainer 45 degrees to allow it to drop out of the bottom of the fixture.
2. Place glass (Q) into glass retainer (S).
3. Lift glass (Q) and glass retainer (S) up to fixture assembly
(O) aligning retainer tabs (R) with fixture slots (P).
4. Lift so retainer tab (R) slips completely through fixture
slot (P).
5. Turn glass (Q) and glass retainer (S) approximately 45
degrees so glass retainer stays in place.
6. Turn tensioning screw (T) to secure glass retainer (S) to
fixture assembly (O). Turn until snug and glass retainer will not spin
(Figure 5)
freely.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21319 Rev B
Loading...