Assembly & Installation Instructions A115
For Compass Semi-Flush 12-4555 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Install the Canopy (Figure 1)
Component Parts
A Crossbar
B Ground Screw
C Hex Nut (2)
D Threaded Nipple
E Coupling
F Canopy
G Canopy Ring
H Socket Assembly
Caution: Be sure power is off at the main breaker box prior to installation.
1. Slip canopy ring (G) large diameter first over threaded nipple (D)
and thread on and over coupling (E) followed by canopy (F)
coming to rest on socket assembly (H).
2. Thread hex nuts (C) and crossbar (A) onto threaded nipple (D)
leave parts loose.
3. Using two machine screws (not provided) fasten the crossbar (A) to
the electric box.
Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.
4. Adjust the length of threaded nipple (D) in crossbar (A) so that
canopy ring (G) will hold canopy (F) against the ceiling with no
threads showing for best appearance. When the correct adjustment
is established, tighten hex nuts (C) against crossbar (A) to hold the
adjustment.
5. Loosen canopy ring (G) from coupling (E) and lower canopy ring
(G) and canopy (F) until they rest on top of socket
assembly (H).
6. Using suitable wire connectors (not provided) connect fixture wires
to supply wires (white to white or ribbed and black to black or
smooth. Connect all ground wires to green ground screw (B). Push
wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.
(Figure 1)
Hand-Forged, Vermont-Made Lighting and Accessorie
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 1)
(continued)
19841 Rev B
Assembly & Installation Instructions A115
For Compass Semi-Flush 12-4555 Page 2 of 2
Install the Threaded Rods
Component Parts
F Canopy
G Canopy Ring
I Knurl Ball (4)
J Threaded Rod (4)
(Figure 2)
1. Slip bent end of threaded rod (J) through holes in canopy (F).
2. Thread knurl ball (I) onto threaded rod (J) until snug against inside of
canopy (F).
3. Slide fixture canopy (F) against ceiling, and secure with canopy ring (G).
(Figure 2)
To Install Glass Frame and Glass
Component Parts
I Knurl Ball (4)
J Threaded Rod (4)
K Glass Frame
L Tab
M Glass
(Figure 3)
1. Slip tabs on glass frame (K) onto three threaded rods (J)
and attach with knurl ball (I).
2. Slip glass (M) into glass frame (K) so it rests below the
three tabs.
3. Slip tab (L) onto last threaded rod (J) and slide onto glass
frame (K).
(Figure 2)
4. Thread knurl ball (I) onto threaded rod (J).
5. Install light bulbs (not provided).
6. Restore electricity at main breaker.
(Figure 3)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessorie
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19841 Rev B
Loading...