Hubbardton Forge 124442 User Manual

Assembly Instructions Page 1 of 2 A3

For Semi-Flush Mount Fixtures—Model Numbers: 12-4412, 12-4422, 12-4432, 12-4442 and 12-4424

Please follow these instructions prior to installing fixture. Installation instructions on backside.

Component Parts

A Canopy
B Support Rods
C Knurled Ball/Nuts
D Ring Assembly

To Attach Support Rods to Canopy

1. Refer to the drawing that corresponds to the model

number of your fixture.

2. Remove Knurled Ball/Nut (C) from one end of each

Support Rod (B).

3. Insert Support Rods (B) through outermost holes in

Canopy (A) and reattach Knurled Balls/Nuts (C). For
models 12-4422, 12-4423, and 12-4442 the straight end
of the rods should be in the canopy (Figure 1).

Note: Model 12-4412 will require the removal of an
insulation pad to install rods. Please make sure that this
pad is replaced prior to installing the fixture.

4. Refer to Installation Instructions (on the back of this

sheet) and install fixture.

Models 12-4422, 12-4432, 12-4442, 12-4424

Figure 1

To Install Glass

1. Install fixture prior to installing glass.

2. Attach Ring Assembly (D) to two of the Support Rods

(B) using Knurled Balls/Nuts (C).

3. Place glass into Ring Assembly.

4. Move ring Assembly (D) into position and secure by

inserting remaining Support Rod (B) into Ring
Assembly and attaching Knurled Ball/Nut (C).

Figure 2

Model 12-4412

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

14007 Rev. A

Installation Instructions Page 2 of 2 A3

For Semi-Flush Mount Fixtures

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions prior to installation.

Component Parts

A Canopy
B Electric Box Machine Screws (not provided)
C Black or Smooth Wires
D Ground Wires
E White or Ribbed Wires

To Install

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Thread studs (G) through appropriate holes in cross bar (F) to match

hole centers in canopy (A).

3. Using two machine screws (B, not provided) fasten cross bar to the

electric box using outer oval holes to orient fixture to desired hanging
position.

Note: A new electric box comes with screws. When replacing an
existing fixture, retain the screws for use with the new fixture.

5. Using suitable wire connectors (I, not provided), connect fixture wires

to supply wires (white to white or ribbed, E) and black to black or
smooth (C). Connect all ground wires (D) to green ground screw (J).

Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.

6. Slide fixture canopy (A) over threaded studs and push firmly to ceiling,

making sure that no wires are pinched between fixture canopy and
ceiling. Fasten with knurled balls (H). Be sure studs (G) are fully
seated in the knurled balls (H).

7. Install light bulb(s) (not provided).

8. Install glass (refer to glass installation instructions if appropriate).

9. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

F Round Cross Bar
G 8-32 Threaded Studs
H 8-32 Knurled Balls
I Wire Nuts or connectors (not provided)
J Green Ground Screw

Figure 3

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

14007 Rev. A