Hubbardton Forge 124247 User Manual

Installation Instructions A34

g

For Semi Flush Pendants with Slide Locking Mechanism Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

For fixtures requiring assembly, please refer to assembly instructions prior to installation.

Component Parts

A Canopy
B Electric Box Machine Screws (not provided)
C Black or Smooth Wires
D Ground Wires
E White or Ribbed Wires

To Install

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

e noted on fixture. Use only recommended bulbs with fixture.

F Round Cross Bar
G 8-32 Threaded Studs
H 8-32 Knurled Balls
I Wire Nuts or connectors (not provided)
J Green Ground Screw

2. Thread studs (G) through appropriate holes in cross bar

(F) to match hole centers in canopy (A). Move ground
screw (J) to another available threaded hole if
necessary.

3. Using two machine screws (B, not provided) fasten

cross bar to the electric box using outer oval holes to
orient fixture to desired hanging position.

Note: A new electric box comes with screws. When
replacing an existing fixture, retain the screws for use with
the new fixture.

5. Using suitable wire connectors (I) (not provided),

connect fixture wires to supply wires (white to white or
ribbed (E) and black to black or smooth (C). Connect
all ground wires (D) to green ground screw (J).

Caution: Make sure wire connectors are twisted on
securely, and no bare wire is exposed.

6. Slide fixture canopy (A) over threaded studs and push

firmly to ceiling, making sure that no wires are pinched
between fixture canopy and ceiling. Fasten with
knurled balls (H). Be sure studs (G) are fully seated in the knurled balls (H).

7. Install light bulb(s) (not provided).

8. Install glass (refer to glass installation instructions if appropriate).

9. Restore electricity at main breaker.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

14532 Rev A

Installation Instructions A34

For Semi Flush Pendants with Slide Locking Mechanism Page 2 of 2

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Component Parts

K Notched Tab
L Fixed Stem
M Hooked Bar
N Ring Assembly
O Glass Bowl

To Install Glass

1. Install light bulb.

2. Place Glass Bowl (O) into ring assembly

3. Slide ring assembly onto fixed stem (L) of fixture.

The fixed stem should slide into the square hole in
the ring assembly (N).

4. Slide ring assembly horizontally to clear the socket

cup and rotate hooked bar (M) of ring assembly into
notched tab (K) in fixture centering the ring assembly
and glass.

Please Note: The glass in this fixture is hand blown which can cause imbalance in the total piece. While all care is taken
to limit the impact of the imbalance, sometimes the glass will hang off to one side. In order to correct for the issue, please
make sure the glass is placed in the holder with the same reveal all around the top ring. If the glass still hangs off, rotate
the glass 90 degrees in the holder to place the heavy side over one of the pivot points. This should resolve the tendency
of this hand craft glass to hang off to one side.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

14532 Rev A