Page 1
Assembly & Installation Instructions A180
For Semi-Flush Vortis Fixtures 12-3250 & 12-3252 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Install Fixture (Figure 1)
Component Parts
A Ground Screw
B Cross Bar
C Threaded Stud (2)
D Canopy
E Barrel Knobs (2)
Caution: Be sure power is off at the main breaker box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Thread studs (C) through appropriate holes in cross bar (B) to match
hole centers in canopy (D). Move ground screw (A) to another available
threaded hole if necessary.
3. Using two machine screws (not provided) fasten cross bar (B) to the
electric box using outer oval holes to orient fixture to desired hanging
position.
Note: A new electric box comes with screws. When replacing an
existing fixture, retain the screws for use with the new fixture.
4. Using suitable wire connectors (not provided); connect fixture wires to
supply wires (white to white and black to black). Connect all ground
wires to green ground screw (A).
Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.
5. Slide fixture canopy (D) over threaded studs and push firmly to ceiling, making sure that no wires are pinched
between fixture canopy and ceiling. Fasten with barrel knobs (E). Be sure studs (C) are fully seated in barrel
knobs (E).
(Figure 1)
To Install Bulb
Component Parts
F Bulb Shield (4)
G Bulb (4)
H Socket
(Figure 2)
(4)
1. Install light bulb (G). Be careful not to touch
bulb with bare hands; oil from the hands will
dramatically reduce bulb life.
2. Thread bulb shield (F) onto socket (H) (be
careful not to over tighten). Future bulb changes
may be accomplished by snapping glass portion
of barrier on and off rather than unthreading the
(Figure 2)
holder.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
21367
Page 2
Assembly & Installation Instructions A180
For Semi-Flush Vortis Fixtures 12-3250 & 12-3252 Page 2 of 2
To Install Glass
(Figure 3)
Component Parts
I Fixture Assembly
J Fixture slot
K Glass
L Retainer Tab
M Glass Retainer
N Tensioning Screw
1. Remove glass retainer (M) from bottom of
fixture by removing tensioning screw (N) and
turning the glass retainer 45 degrees to allow it
to drop out of the bottom of the fixture.
2. Place glass (K) into glass retainer (M).
3. Lift glass (K) and glass retainer (M) up to
fixture assembly (I) aligning retainer tabs (L)
with fixture slots (J).
4. Lift so retainer tab (L) slips completely through
fixture slot (J).
5. Turn glass (K) and glass retainer (M)
approximately 45 degrees so glass retainer stays
in place.
6. Turn tensioning screw (N) to prevent glass
retainer (M) to lift and possibly drop out of
fixture assembly (I). Turn until snug and glass
retainer will not spin freely.
(Figure 3)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21367
Loading...