Hubbardton Forge 104815 User Manual

Installation Instructions A212

g

For Beacon Hall Four Light Chandelier 10-4815 & 10-4815E Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products and
options.

To Install (Figure 1)

Component Parts

A Crossbar
B Lock Nut
C Nipple
D Canopy
E Loop Collar

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the crossbar to the electric

box.

Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.

3. Thread the nipple (C) into the crossbar (A) and secure with lock nut (B);

slide canopy (D) over nipple, and attach the canopy loop (F) to the nipple.
Adjust the nipple to proper length to ensure a snug canopy fit before
proceeding.

4. Attach one end of the chain to the fixture loop (H). Lace the wire through

every other link of the chain (G) to the end. Slip wires and chain through the
loop collar (E), canopy loop (F) and canopy (D). Fasten the chain to the
canopy loop, then slip wires through the loop and nipple, into the electric
box. Make sure to provide enough slack in the wire to ensure weight of
fixture is supported by the chain.

5. Using suitable wire connectors (not provided) connect fixture wires to supply

wires (white to ribbed side of the fixture cord, black to smooth side). Connect
all ground wires to crossbar ground screw (J).

Caution: Make sure wire connectors are twisted on securely, and no bare
wire is exposed.

6. Raise canopy to the ceiling and secure collar to canopy loop (F) with loop

collar (E).

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

e noted on fixture. Use only recommended bulbs with fixture.

F Canopy Loop
G Chain
H Fixture Loop
I Fixture
J Ground Screw

(Figure 1)

(continued)

22850

Installation Instructions A212

For Beacon Hall Four Light Chandelier 10-4815 & 10-4815E Page 2 of 2

To Install Glass

Component Parts

K Socket (4)
L Glass (4)
M Retaining Ring (4)
N Socket Tool

1. Remove retaining rings (M) from sockets (K). Retaining

Rings are shipped installed.

2. Slip glass (L) over socket (K).

3. Thread retaining ring (M) onto socket (K) using provided

socket tool (N) provided until it rests on inside of glass (L). Do
not over tighten.

4. Install light bulbs. “E” version bulbs are included.

To Install Shade

(Figure 2)

(Figure 3)

Component Parts

O Shade
P Knurl Balls (4)
Q Threaded Stud (4)
R Shade Bracket

(Figure 2)

1. Remove four knurl balls (P) that are shipped

installed. Save for later use.

2. Raise shade (O) from bottom until the top clears

the shade bracket (R) and slip over threaded
studs (Q).

3. Thread four knurl balls (P) on to threaded studs

(Q) until snug.

4. Restore electricity at main breaker.

(Figure 3)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22850