Page 1
Installation Instructions A266
For Constellation Chandelier 10-4303 & 10-4305 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Install the Canopy (Figure 1)
Component Parts
A Ground Screw
B Crossbar
C Lock Nut
D Nipple
E Canopy
Caution: Be sure power is off at the main breaker box prior to installation
1. Carefully unpack the fixture from the carton.
2. Using two machine screws (not provided), fasten the crossbar (B) to
the electric box (see illustration).
Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.
3. Thread the nipple (D) into the crossbar (B) and secure with lock nut
(C); slide canopy (E) over nipple (D), and attach the canopy loop (G)
to the nipple (D). Adjust the nipple to proper length to ensure a snug
canopy fit before proceeding.
4. Attach one end of the chain (I) to the fixture loop (H). Lace the wire
through every other link of the chain (I) to the end. Slip wires and
chain (I) through the collars and canopy (G, F & E). Fasten the chain
(I) to the canopy loop (G), then slip wires through the loop and nipple,
into the electric box. Make sure to provide enough slack in the wire to
ensure weight of fixture is supported by the chain (I).
5. Using suitable wire connectors (not provided) connect fixture wires to
supply wires (white to ribbed side of the fixture s cord, black to
smooth side). Run a pigtail lead from crossbar ground screw (A) to the
junction box and connect all ground wires (bare copper or green to
bare copper or green).
Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.
6. Raise canopy (E) to the ceiling and secure loop collar (F) to canopy
loop (G).
F Loop Collar
G Canopy Loop
H Fixture Loop
I Chain
fixture and may not match every style.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 1)
This illustration represents a typical
(continued)
24838
Page 2
Installation Instructions A266
For Constellation Chandelier 10-4303 & 10-4305 Page 2 of 2
To Install Glass
Component Parts
J Socket
K Bulb (Included)
L Inner Glass
M Outer Glass
N Glass Spring Clip
1. Install light bulb (K). Be careful not to touch bulb with bare hands; oil
from the hands will dramatically reduce bulb life.
2. Slip inner glass (L) over socket (J) until it engages with glass spring
clip (N).
3. If glass has a loose fit the glass spring clip (N) can be adjusted by taking a
pair of needle noose pliers and bending the three prongs outward.
4. Install outer glass (M).
5. Restore electricity at main breaker.
(Figure 2)
(Figure 2)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24838
Loading...