Page 1
Installation Instructions A184
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 1)
Ribbon Chandelier 10-4103, 10-4103F, 10-4105, 10-4105F, 10-4106, 10-4106E, 10-4107 & 10-4107F Page 1 of 2
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance w ith app lic able insta ll ati on code( s ), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Install the Canopy (Figure 1)
Component Parts
A Ground Screw
B Crossbar
C Lock Nut
D Nipple
Caution: Be sure power is off at the main breaker box prior to installation
1. Carefully unpack the fixture from the carton.
2. Using two machine screws (not provided), fasten the crossbar (B)
to the electric box (see illustration).
Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.
3. Thread the nipple (D) into the crossbar (B) and secure with lock
nut (C); slide canopy (E) over nipple (D), and attach the canopy
loop (F) to the nipple (D). Adjust the nipple to proper length to
ensure a snug canopy fit before proceeding.
4. Attach one end of the chain to the fixture loop (H). Lace the wire
through every other link of the chain to the end. Slip wires and
chain through the collars and canopy (G, F & E). Fasten the chain
to the canopy loop (F) then slip wires through the loop and nipple,
into the electric box. Make sure to provide enough slack in the
wire to ensure weight of fixture is supported by the chain.
5. Using suitable wire connectors (not provided) connect fixture
wires to supply wires (white to ribbed side of the fixture s cord,
black to smooth side). Run a pigtail lead from crossbar ground
screw (A) to the junction box and connect all ground wires (bare
copper or green to bare copper or green).
6.
Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.
7. Raise canopy (E) to the ceiling and secure loop collar (G) to
canopy loop (F).
E Canopy
F Cano p y Loop
G Loop Collar
H Fixture Loop
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
22021 Rev A
(continued)
Page 2
Installation Instructions A184
(Figure 2)
Ribbon Chandelier 10-4103, 10-4103F, 10-4105, 10-4105F, 10-4106, 10-4106E, 10-4107 & 10-4107F Page 2 of 2
To Install Glass (Figure 2)
Component Parts
I Retaining Ring
J Glass
K Socket
L Socket Tool
1. Remove retaining ring (I) from socket (K). Retaining Rings are shipped
installed.
2. Place glass (J) over socket (K).
3. Replace retaining ring (I) and tighten with socket tool (L) to secure
glass. Do not over-tighten.
4. Install light bulb (fluorescent vers ions; bulbs included).
5. Restore electricity at the main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
22021 Rev A
Loading...