Hubbardton Forge 103047 User Manual

Installation Instructions A298

y

Flora Chandeliers 10-3045 & 103047 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install the Canopy (Figure 1)

Component Parts

A Ground Screw
B Crossbar
C Lock Nut
D Nipple
E Canopy

Caution: Be sure power is off at the main breaker box
prior to installation

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten

the crossbar (B) to the electric box (see
illustration).

Note: A new electric box comes with screws.
When replacing a fixture, retain the existing
screws for use with the new fixture.

3. Thread the nipple (D) into the crossbar (B) and

secure with lock nut (C); slide canopy (E) over
nipple (D), and attach the canopy loop (G) to the
nipple (D). Adjust the nipple to proper length to
ensure a snug canopy fit before proceeding.

4. Attach one end of the chain (I) to the fixture loop

(H). Lace the wire through every other link of the
chain (I) to the end. Slip wires and chain (I)
through the collars and canopy (G, F & E). Fasten
the chain (I) to the canopy loop (G), and then slip
wires through the loop and nipple, into the electric
box. Make sure to provide enough slack in the
wire to ensure weight of fixture is supported by
the chain (I).

5. Using suitable wire connectors (not provided)

connect fixture wires to supply wires (white to
ribbed side of the fixture cord, black to smooth
side). Run a pigtail lead from crossbar ground
screw (A) to the junction box and connect all
ground wires (bare copper or green to bare
copper or green).

Caution: Make sure wire connectors are twisted on
securely, and no bare wire is exposed.

6. Raise canopy (E) to the ceiling and secure loop collar (F) to canopy loop (G).

7. Follow instructions on next page to install glass.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

F Loop Collar
G Canopy Loop
H Fixture Loop
I Chain

(Figure 1)

This illustration represents a typical
fixture and ma

not match every style.

(continued)

27015 Rev A

Installation Instructions A298

Flora Chandeliers 10-3045 & 103047 Page 2 of 2

To Install Single Glass Option

Component Parts

J Socket
K Bulb (Included)
L Glass
M Retaining Ring

N Retaining Ring Tool

(Figure 2)

1. Remove retaining ring (M) from socket (J) and retain.

Retaining ring ships installed.

2. Install light bulb (K). Be careful not to touch bulb with

bare hands; oil from the hands will dramatically reduce
bulb life.

Note: The bulb included is based on our design
preference; see the fixtures wattage sticker for Max
wattage information.

3. Slip glass (L) over socket (J) and thread retaining ring (M)

onto socket (J) using provided retaining ring tool (N).

4. Repeat steps 1-4 for remaining sockets.

5. Restore electricity at main breaker.

To Install Double Glass Option

(Figure 3)

(Figure 2)

Component Parts

J Socket
K Bulb (Included)
L Glass
M Retaining Ring
N Retaining Ring Tool
O Inner Glass

1. Remove retaining ring (M) from socket (J) and retain.

Retaining ring ships installed.

2. Install light bulb (K). Be careful not to touch bulb with bare

hands; oil from the hands will dramatically reduce bulb life.

Note: The bulb included is based on our design preference;
see the fixture wattage sticker for Max wattage information.

3. Place inner glass (O) inside glass (L) and then slip glass (L)

over socket (J). Thread retaining ring (M) onto socket (J)
using provided retaining ring tool (N).

4. Repeat steps 1-4 for remaining sockets.

5. Restore electricity at main breaker.

These illustrations represent a typical
fixture and may not match every style.

(Figure 3)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

27015 Rev A