Hubbardton Forge 103043 User Manual

Installation Instructions A306

Flora Chandelier 10-3043 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install the Canopy (Figure 1)

Component Parts

A Ground Screw
B Crossbar
C Lock Nut
D Nipple
E Canopy

Caution: Be sure power is off at the main breaker box prior to
installation

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the crossbar (B)

to the electric box (see illustration).

Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.

3. Thread the nipple (D) into the crossbar (B) and secure with lock

nut (C); slide canopy (E) over nipple (D), and attach the canopy
loop (G) to the nipple (D). Adjust the nipple to proper length to
ensure a snug canopy fit before proceeding.

4. Attach one end of the chain (I) to the fixture loop (H). Lace the

wire through every other link of the chain (I) to the end. Slip wires
and chain (I) through the collars and canopy (G, F & E). Fasten the
chain (I) to the canopy loop (G), and then slip wires through the
loop and nipple, into the electric box. Make sure to provide
enough slack in the wire to ensure weight of fixture is supported
by the chain (I).

5. Using suitable wire connectors (not provided) connect fixture

wires to supply wires (white to ribbed side of the fixture cord,
black to smooth side). Run a pigtail lead from crossbar ground
screw (A) to the junction box and connect all ground wires (bare
copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.

6. Raise canopy (E) to the ceiling and secure loop collar (F) to

canopy loop (G).

7. Follow instructions on next page to install glass.

F Loop Collar
G Canopy Loop
H Fixture Loop
I Chain

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

27185

Installation Instructions A306

Flora Chandelier 10-3043 Page 2 of 2

To Install Single Glass Option

Component Parts

J Socket
K Bulb (Included)
L Glass
M Retaining Ring

N Retaining Ring Tool

(Figure 2)

1. Remove retaining ring (M) from socket (J) and retain. Retaining ring ships

installed.

2. Install light bulb (K). Be careful not to touch bulb with bare hands; oil from

the hands will dramatically reduce bulb life.

Note: The bulb included is based on our design preference; see the fixtures
wattage sticker for Max wattage information.

3. Slip glass (L) over socket (J) and thread retaining ring (M) onto socket (J)

using provided retaining ring tool (N).

4. Repeat steps 1-3 for remaining sockets.

5. Restore electricity at main breaker.

To Install Double Glass Option

Component Parts

J Socket
K Bulb (Included)
L Glass
M Retaining Ring
N Retaining Ring Tool
O Inner Glass

(Figure 3)

(Figure 2)

1. Remove retaining ring (M) from socket (J) and retain. Retaining ring

ships installed.

2. Install light bulb (K). Be careful not to touch bulb with bare hands; oil

from the hands will dramatically reduce bulb life.

Note: The bulb included is based on our design preference; see the
fixture wattage sticker for Max wattage information.

3. Place inner glass (O) inside glass (L) and then slip glass (L) over socket

(K). Thread retaining ring (M) onto socket (J) using provided retaining
ring tool (N).

4. Repeat steps 1-3 for remaining sockets.

5. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please
contact the dealer from which you purchased this product. We hope you
enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper
installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

27185

(Figure 3)