Hubbardton Forge 103040 User Manual

Installation Instructions A211

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

(Figure 1)

Flora Chandelier 10-3040 Page 1 of 2

INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install the Canopy (Figure 1)

Component Parts

A Ground Screw
B Crossbar
C Lock Nut
D Nipple

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the crossbar

(B) to the electric box (see illustration).

Note: A new electric box comes with screws. When replacing
a fixture, retain the existing screws for use with the new fixture.

3. Thread the nipple (D) into the crossbar (B) and secure with

lock nut (C); slide canopy (E) over nipple (D), and attach the
canopy loop (F) to the nipple (D). Adjust the nipple to proper
length to ensure a snug canopy fit before proceeding.

4. Attach one end of the chain to the fixture loop (H). Lace the

wire through every other link of the chain to the end. Slip wires
and chain through the collars and canopy (G, F & E). Fasten
the chain to the canopy loop (F), then slip wires through the
loop and nipple, into the electric box. Make sure to provide
enough slack in the wire to ensure weight of fixture is
supported by the chain.

5. Using suitable wire connectors (not provided) connect fixture

wires to supply wires (white to ribbed side of the fixture s cord,
black to smooth side). Run a pigtail lead from crossbar ground
screw (A) to the junction box and connect all ground wires
(bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely,
and no bare wire is exposed.

6. Raise canopy (E) to the ceiling and secure loop collar (G) to

canopy loop (F).

E Canopy
F Cano p y Loop
G Loop Collar
H Fixture Loop

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

22849 Rev A

(continued)

Installation Instructions A211

(Figure 2)

(Figure 3)

(Figure 4)

Flora Chandelier 10-3040 Page 2 of 2

To Install Opaque Glass (Figure 2)

Component Parts

I Retaining Ring (5)
J Glass (5)
K Socket (5)
L Socket Tool

1. Remove retaining ring (I) from socket (K). Retaining Rings are shipped

installed.

2. Place glass (J) over socket (K).

3. Replace retaining ring (I) and tighten with socket t ool (L) to secure glass.

Do not over-tighten.

4. Install light bulbs.

5. Restore electricity at the main breaker.

To Install Water Glass (Figures 3 & 4)

Component Parts

I Retaining Ring (5)
J Glass (5)
K Socket (5)
M Decorative Ring Cover (5)

1. Remove retaining ring (I) from socket (K). Retaining Rings are shipped

installed.

2. Install retaining ring (I) into decorative ring cover (M). If retaining ring (I)

fits to loose bend a few inside tabs of the decorative ring cover (M)
(Figure 4).

3. Place glass (J) over socket (K).

4. Replace retaining ring (I) and tighten to secure glass. Do not over-tighten.

5. Install light bulb.

6. Restore electricity at the main breaker.

If you need further assistance, or find that you are missing any parts, please
contact the dealer from which you purchased th is product. We hope you enjoy
your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper
installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

22849 Rev A