Page 1
Assembly & Installation Instructions A161
For Berceau Seven-Light Chandelier 10-1283F Page 1 of 2 _
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Install the Canopy (Figure 1)
Component Parts
A Crossbar
B Threaded Nipple
C Lag Screw (2)
D Lock Nut
E Canopy
Caution: Be sure power is off at the main breaker box prior to installation.
Caution: This fixture must be supported independently of an outlet box. Crossbar
is designed to fit in the bottom of a standard metal 4” octagonal outlet box.
F Loop Collar
G Threaded Loop
H Chain
I Fixture Loop
J Ground Screw
K Cupped Washer
L Hex Nut
(Figure 1)
1. Drill two holes through the back of the outlet box and using two lag screws
(C) attach cross bar (A) to a structural member in the ceiling, centering the
crossbar in the outlet box. We've supplied lag screws with your fixture;
however, different materials and/or construction methods may require
different fasteners. If in doubt, contact a qualified electrician.
2. Thread the nipple (B) into the crossbar (A).
3. Thread lock nut (D) and threaded loop (G) onto nipple, then place canopy
(E) over threaded loop and adjust nipple length to ensure a snug canopy fit.
Once the length is determined, set the canopy aside and lock nipple
position by tightening the locknut (D) against the crossbar (A).
4. Attach one end of the chain (H) to the fixture loop (I).
5. Attach the other end of the chain to the threaded loop (F) and thread the
fixture wires through every other link of the chain (H) and up through the
threaded loop (G) and nipple (B) into the outlet box.
6. Using suitable wire connectors (not provided), connect fixture wires to
supply wires (white or ribbed side of fixture cord to white supply, black or
smooth side of fixture cord to black supply, and bare copper to bare copper
or green supply). Ground the crossbar (A) using the ground screw (J),
cupped washer (K) and hex nut (L) to secure a pigtail lead to the crossbar.
Push wires back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and no bare
wire is exposed.
7. Slide the canopy up the chain and over the threaded loop (G), securing
with loop collar (F). Make sure no wires are pinched between the canopy
(E) and the ceiling or crossbar (A).
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 1)
(continued)
21249
Page 2
Assembly & Installation Instructions A161
For Berceau Seven-Light Chandelier 10-1283F Page 2 of 2 _
To Install Glass
Component Parts
M Retaining Ring (7)
N Glass (7)
O Socket (7)
P Socket Tool
1. Remove retaining ring (M) from socket (O). Retaining Rings are shipped installed.
2. Place glass (N) over socket (O).
3. Replace retaining ring (M) and tighten with tool (P) to secure glass. Do not over-tighten.
4. Install light bulb. Included with fixture.
5. Restore electricity at the main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(Figure 2)
(Figure 2)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21249
Loading...