Hubbardton Forge 101283 User Manual

Assembly & Installation Instructions A160

For Berceau Seven-Light Chandelier 10-1283 Page 1 of 2 _

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Install the Canopy (Figure 1)

Component Parts

A Crossbar
B Threaded Nipple
C Lag Screw (2)
D Lock Nut
E Canopy
F Loop Collar

Caution: This fixture must be supported independently of an outlet box.
Crossbar is designed to fit in the bottom of a standard metal 4” octagonal outlet
box.

Caution: Be sure power is off at the main breaker box prior to installation.

G Threaded Loop
H Chain
I Fixture Loop
J Ground Screw
K Cupped Washer
L Hex Nut

1. Drill two holes through the back of the outlet box and using two lag

screws (C) attach cross bar (A) to a structural member in the ceiling,
centering the crossbar in the outlet box. We've supplied lag screws
with your fixture; however, different materials and/or construction
methods may require different fasteners. If in doubt, contact a qualified
electrician.

2. Thread the nipple (B) into the crossbar (A).

3. Thread lock nut (D) and threaded loop (G) onto nipple, then place

canopy (E) over threaded loop and adjust nipple length to ensure a
snug canopy fit. Once the length is determined, set the canopy aside
and lock nipple position by tightening the locknut (D) against the
crossbar (A).

4. Attach one end of the chain (H) to the fixture loop (I).

5. Attach the other end of the chain to the threaded loop (F) and thread

the fixture wires through every other link of the chain (H) and up
through the threaded loop (G) and nipple (B) into the outlet box.

6. Using suitable wire connectors (not provided), connect fixture wires to

supply wires (white or ribbed side of fixture cord to white supply,
black or smooth side of fixture cord to black supply, and bare copper to
bare copper or green supply). Ground the crossbar (A) using the
ground screw (J), cupped washer (K) and hex nut (L) to secure

(Figure 1)

a pigtail lead to the crossbar. Push wires back into outlet box.

Caution: Make sure wire connectors are twisted on securely,
and no bare wire is exposed.

7. Slide the canopy up the chain and over the threaded loop (G), securing with loop collar (F). Make sure no wires

are pinched between the canopy (E) and the ceiling or crossbar (A).

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21244

(Figure 1)

(continued)

Assembly & Installation Instructions A160

For Berceau Seven-Light Chandelier 10-1283 Page 2 of 2 _

To Install Glass

Component Parts

M Retaining Ring (7)
N Glass (7)
O Socket (7)
P Washer (7)
Q Socket Tool

(Figure 2)

1. Remove retaining ring (M) from socket (O).

Retaining Rings are shipped installed.

2. Place glass (N) over socket (O).

3. Place washer (P) over socket (O) until it rests

on the bottom inside of glass (N).

4. Replace retaining ring (M) and tighten with tool

(Q) to secure glass. Do not over-tighten.

5. Install light bulb.

6. Restore electricity at the main breaker.

(Figure 2)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21244