Hubbardton Forge 101281F User Manual

Installation Instructions A165

For Berceau Chandelier 10-1280F & 10-1281F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install the Canopy (Figure 1)

Component Parts

A Ground Screw
B Crossbar
C Lock Nut
D Nipple

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the crossbar (B) to the

electric box (see illustration).

Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.

4. Thread the nipple (D) into the crossbar (B) and secure with lock nut (C);

slide canopy (E) over nipple (D), and attach the canopy loop (F) to the nipple
(D). Adjust the nipple to proper length to ensure a snug canopy fit before
proceeding.

5. Attach one end of the chain to the fixture loop (H). Lace the wire through

every other link of the chain to the end. Slip wires and chain through the
collars and canopy (G, F & E). Fasten the chain to the canopy loop (F), then
slip wires through the loop and nipple, into the electric box. Make sure to
provide enough slack in the wire to ensure weight of fixture is supported by
the chain.

6. Using suitable wire connectors (not provided) connect fixture wires to supply

wires (white to ribbed side of the fixture s cord, black to smooth side).
Connect all ground wires to crossbar ground screw (A).

Caution: Make sure wire connectors are twisted on securely, and no bare
wire is exposed.

7. Raise canopy (E) to the ceiling and secure loop collar (G) to canopy

loop (F).

E Canopy
F Canopy Loop
G Loop Collar
H Fixture Loop

(Figure 1)

fixture and may not match every style.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

This illustration represents a typical

(continued)

21287

Installation Instructions A165

For Berceau Chandelier 10-1280F & 10-1281F Page 2 of 2

To Install Glass

Component Parts

I Retaining Ring (3 each/3-arm, 5 each/5-arm)
J Glass (3 each/3-arm, 5 each/5-arm)
K Socket (3 each/3-arm, 5 each/5-arm)
L Socket Tool

(Figure 2)

1. Remove retaining ring (I) from socket (K). Retaining Rings

are shipped installed.

2. Place glass (J) over socket (K).

3. Replace retaining ring (I) and tighten with socket tool (L) to

secure glass. Do not over-tighten.

4. Install light bulb. Included with fixture.

5. Restore electricity at the main breaker.

(Figure 2)

This illustration represents a typical

fixture and may not match every style.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21287