HTP PHP260-119, PHP199-119, PHP320-119, PHP399-119 Installation, Setup, Maintenance

Download

Page 1

Installation

Start-Up

Maintenance

Parts

Warranty

Phoenix Plus

Water Heater

PHP Models*

* “LP” Denotes Propane Gas Operation

This manual must only be used by a qualied installer / service technician. Read all instructions in this manual before installing. Perform steps in the given order. Failure to do so could result in substantial property damage, severe personal injury, or death.

Improper installation, adjustment, alteration, service, or maintenance could void product warranty and cause property damage, severe personal injury, or death.

California Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

HTP reserves the right to make product changes or updates without notice and will not be held liable for typographical errors in literature.

The surfaces of these products contacted by potable (consumable) water contain less than 0.25% lead by weight as required by the Safe Drinking Water Act, Section 1417.

NOTE TO CONSUMER: PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.

This Manual For Use With Water Heaters Manufactured After

April 10, 2017

272 Duchaine Blvd. New Bedford, MA 02745 www.htproducts.com

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 2

WARNING: If the information in these instructions is not followed exactly, a re or explosion may result causing property damage, personal injury or death.

• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

• Installation and service must be provided by a qualied installer, service agency or the gas supplier.

Improper installation, adjustment, alteration, service, or maintenance can cause injury, property damage, or death. Refer to this manual. Installation and service must be performed by a qualied installer, service agency, or gas supplier.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 3

The following dened terms are used throughout this manual to bring attention to the presence of hazards of various risk levels or to important product information.

DANGER indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury or death.

companies which pertain to this type of water heating equipment.

Authority Having Jurisdiction (AHJ) – The AHJ may be a federal, state, local government, or individual such as a re chief, re marshal, chief of a re prevention bureau, labor department or health department, building ocial or electrical inspector, or others having statutory authority. In some circumstances, the property owner or his/her agent assumes the role, and at government installations, the commanding ocer or departmental ocial may be the AHJ.

NOTE: HTP, Inc. reserves the right to modify product technical specications and components without prior notice.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in personal injury or death.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor personal injury.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

NOTICE is used to address practices not related to personal injury.

Foreword

This manual is intended to be used in conjunction with other literature provided with the water heater. This includes all related control information. It is important that this manual, all other documents included in this system, and additional publications including the Code for the Installation of Heat Producing Appliances and National Fuel Gas Code - ANSI Z223.1 (latest versions), be reviewed in their entirety before beginning any work.

Installation should be made in accordance with the regulations of the Authority Having Jurisdiction, local code authorities, and utility

For the Installer

This water heater must be installed by qualied and licensed personnel. The installer should be guided by the instructions furnished with the water heater, and by local codes and utility company requirements. In the absence of local codes, preference should be given to the National Fuel Gas Code - ANSI Z223.1, latest version.

Installations Must Comply With:

Local, state, provincial, and national codes, laws, regulations, and ordinances.

The latest version of the National Fuel Gas Code, ANSI Z223.1, from American Gas Association Laboratories, 8501 East Pleasant Valley Road, Cleveland, OH 44131.

In Canada - CGA No. B149 (latest version), from Canadian Gas Association Laboratories, 55 Scarsdale Road, Don Mills, Ontario, Canada M3B 2R3. Also, Canadian Electrical Code, C 22.1, from Canadian Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6.

Code for the Installation of Heat Producing Appliances (latest version) from American Insurance Association, 85 John Street, New York, NY

11038.

The latest version of the National Electrical Code, NFPA No. 70.

NOTE: The gas manifold and controls met safe lighting and other performance criteria when undergoing tests specied in ANSI Z21.10.3

- latest edition.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 4

Table of Contents

Part 1 - General Safety Information 4

A. Improper Combustion 5 B. Gas 5 C. When Servicing the Water Heating System 5 D. Heater Water 5 E. Freeze Protection 5 F. High Elevation Installations 5 G. Water Temperature Adjustment 5

Part 2 - Before You Start 6

A. What’s in the Box 6 B. How the Heater Operates 6 C. Optional Equipment 6

Part 3 - Prepare the Water Heater 6

A. Locating the Water Heater 6 B. Leveling 8 C. Clearances for Service Access 8 D. Residential Garage and Closet Installations 8 E. Exhaust Vent and Intake Pipe 9

1. Indoor Direct Vent of Exhaust and Intake 9

2. Power Venting, Indoor Combustion Air in Conned or Unconned Space

3. Outdoor Installation 9

F. Carbon Monoxide Detectors 10 G. Prevent Combustion Air Contamination 10 H. Removing a Heater from a Common Vent System 10 I. Water Chemistry Requirements 11

Part 4 - Piping 13

A. Heater Plumbing 13 B. Auxiliary Connection 13 C. Backow Preventer 13 D. Potable Expansion Tank 13 E. Temperature and Pressure Relief Valve 13 F. Scalding 14 G. Filling the Heater 14 H. Applications 15

Part 5 - Venting 16

A. General 16 B. Approved Materials for Exhaust Vent and Intake Pipe 17 C. Additional Requirements for Installation in Canada 17 D. Exhaust Vent and Intake Pipe Location 18 E. Exhaust Vent and Intake Pipe Sizing 19 F. Exhaust Vent and Intake Pipe Installation 19 G. Applications 20

1. Indoor Direct Vent Installation of Exhaust and Intake 20

2. Venting Through an Existing System 22

3. Power Venting, Indoor Combustion Air in Conned or Unconned Space 23

4. Outdoor Installation 25

Part 6 - Condensate Removal 26 Part 7 - Wiring 27

A. Line Voltage Input 27 B. Line Voltage Condensate Output 27 C. Internal Wiring Diagram 28

Part 8 - Gas Connections 30

A. Gas Pipe Sizing Tables 31

1. Gas Pipe Sizing 31

2. Natural Gas Pipe Sizing 31

3. LP (Liquid Propane) Gas Pipe Sizing 31

B. Gas Piping Requirements 31 C. Gas Valve 32 D. Checking Gas Pressure at the Water Heater for Proper Operation

Part 9 - Start-Up Procedure 33

A. Operating Instructions 33 B. Overall Water Heater and Control Operation 33 C. Status Menu 33 D. Test Mode 33

E. Maintenance 34

Part 10 - Shutdown 34

A. Shutdown Procedure 34 B. Vacation Procedure 34 C. Failure to Operate 34 D. Important Notice 34

Part 11 - Troubleshooting 35

A. Error Code 35 B. Heater Error 35 C. Lockout 35

Part 12 - Installation Checklist 37 Part 13 - Maintenance 38 Part 14 - Replacement Parts 40

Limited Warranty 42 Maintenance Notes 44 Customer Installation Record Form 45

Part 1 - General Safety Information

Indoor Installation

This water heater is approved for indoor installations and is not intended for use as a pool heater. Clearance to combustible

materials: 0” top, bottom, sides, and back. Heater must have room for service: 24” front and 12” sides are minimum recommended service clearances. (A combustible door or removable panel is acceptable front clearance.) This water heater has been approved for closet installation and installation on combustible ooring. Do not install directly on carpeting. Install the water heater in a location where temperature and pressure relief valve discharge or a leak will not result in damage to the surrounding area. If such a location is not available, install an auxiliary catch pan. Use only Category IV vent systems.

Outdoor Installation

This water heater is approved for outdoor installations and is not intended for use as a pool heater. Clearance to combustible materials: 0” top, bottom, sides, and back. Heater must have room for service: 24” front and 12” sides are minimum recommended service clearances. Special attention should be paid to ensure that T&P valve discharge and drainage from condensate line will not adversely aect the surrounding area or pose a hazard in freezing conditions.

This water heater has a condensate disposal system that may freeze if exposed to sustained temperatures below 32oF. Precautions should be taken to protect the condensate trap and drain lines from freezing conditions. Failure to take precautions could result in property damage, serious personal injury, or death.

Installer - Read all instructions in this manual before installing. Perform steps in the given order.

User - This manual is for use only by a qualied heating installer / service technician. Have this water heater serviced / inspected annually by a qualied service technician.

FAILURE TO ADHERE TO THE GUIDELINES ON THIS PAGE CAN RESULT IN SUBSTANTIAL PROPERTY DAMAGE, SEVERE PERSONAL INJURY, OR DEATH.

NOTE: Obey all local codes. Obtain all applicable permits before

installing the water heater.

NOTE: Install all system components and piping in such a manner that does not reduce the performance of any re rated assembly.

Altering any HTP, Inc. water heater with parts not manufactured by HTP, Inc. WILL INSTANTLY VOID the water heater warranty and could result in property damage, personal injury, or death.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 5

NOTE: If the water heater is exposed to the following, do not operate. Immediately call a qualied service technician.

1. Fire

2. Damage

3. Water Failure to follow this information could result in property damage, severe personal injury, or death.

DO NOT USE THIS WATER HEATER IF ANY PART HAS BEEN SUBMERGED IN WATER. Immediately call a qualied service

technician. The water heater MUST BE replaced if it has been submerged. Attempting to operate a water heater that has been submerged could create numerous harmful conditions, such as a potential gas leakage causing a re and/or explosion, or the release of mold, bacteria, or other harmful particulates into the air. Operating a previously submerged water heater could result in property damage, severe personal injury, or death. NOTE: Water heater damage due to ood or submersion is considered an Act of God, and IS NOT covered under product warranty.

This water heater has been designed to heat potable water ONLY. Using this water heater to heat non-potable uid WILL VOID product warranty, and could result in property damage, personal injury, or death.

To avoid severe burns, allow water heater and associated equipment to cool before servicing.

D. Heater Water

Do not use petroleum-based cleaning or sealing compounds in a water heating system. Gaskets and seals in the system may be damaged. This can result in substantial property damage.

Do not use “homemade cures” or “patent medicines”. Damage to the water heater, substantial property damage, and/or serious personal injury may result.

E. Freeze Protection

NOTE: Consider piping and installation when determining heater

location.

Failure of the water heater due to freeze related damage IS NOT covered by product warranty.

NEVER use any toxic chemical, including automotive, standard glycol antifreeze, or ethylene glycol made for hydronic (non-potable) systems. These chemicals can attack gaskets and seals in water systems, are poisonous if consumed, and can cause personal injury or death.

Do not use this water heater for anything other than its intended purpose (as described in this manual). Doing so could result in property damage and WILL VOID product warranty.

High heat sources (sources generating heat 100 greater, such as stove pipes, space heaters, etc.) may damage plastic components of the water heater as well as plastic vent pipe materials. Such damages ARE NOT covered by warranty. It is recommended to keep a minimum clearance of 8” from high heat sources. Observe heat source manufacturer instructions, as well as local, state, provincial, and national codes, laws, regulations and ordinances when installing this water heater and related components near high heat sources.

F / 37

C or

A. Improper Combustion

Do not obstruct the ow of combustion and ventilating air. Adequate air is necessary for safe operation. Failure to keep the exhaust vent and combustion air intake clear of ice, snow, or other debris could result in property damage, serious personal injury, or death.

B. Gas

Should overheating or gas supply fail to shut o, turn o the manual gas control valve to the water heater.

C. When Servicing the Water Heating System

Be sure to disconnect electrical power before performing service. Failure to do so could result in electrical shock, property damage, serious personal injury, or death.

To avoid electric shock, disconnect electrical supply before performing maintenance.

NOTE: When inquiring about service or troubleshooting, reference the model and serial numbers from the water heater rating label.

UNCRATING THE WATER HEATER - Any claims for damage or shortage in shipment must be led immediately against the transportation company by the consignee.

F. High Elevation Installations

Natural gas at high elevation might contain less heating value than typical 1,000 BTU/cu ft and therefore can cause improper air / gas mix leading to improper combustion. For natural gas installations above 3,000 ft, call your gas provider to determine the heating value of the supplied natural gas.

G. Water Temperature Adjustment

If the water heater is going to have a set temperature above 120oF, you must use an ASSE 1017 rated mixing valve to avoid severe burns or death from scalding temperatures.

Households with small children, disabled, or elderly persons may require a 120oF or lower temperature setting to prevent severe personal injury or death due to scalding.

Approximate Time / Temperature Relationships in Scalds

120oF More than 5 minutes

125oF 1 1/2 to 2 minutes

130oF About 30 seconds

135oF About 10 seconds

140oF Less than 5 seconds

145oF Less than 3 seconds

150oF About 1 1/2 seconds

155oF About 1 second

Table 1 - Approximate Time / Temperature Relationships in Scalds

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 6

Part 2 - Before You Start

Remove all sides of the shipping crate of the water heater.

A. What’s in the Box

Components included with the water heater:

• Temperature and Pressure Relief Valve

• Brass Tee and Bushing

• LP Conversion Kit (NG Models Only)

• Installation Manual and Warranty

• User’s Information Manual

B. How the Heater Operates

Modulating Condensing Technology is an intelligent system that

delivers highly ecient water heating, maximizing eciency by measuring the data parameters of your water heating system. Some of its features are:

Stainless Steel Water Storage Tank

The stainless steel water storage tank has a combustion chamber submerged into the tank water. When the water heater is red, combustion gases heat the combustion chamber walls, transferring heat directly into the surrounding water. These hot gases are blown into secondary heat exchanger coils, where more heat from these gases is transferred into the water.

Dual Modulating Combustion Systems

The water heater is provided with two independent combustion systems (PHP-199-119 models have a single combustion system). Each combustion system has a separate control that modulates burner output based on measurements taken by water temperature sensors located within the upper and lower portions of the storage tank, eciently regulating burner output to match system demand. These systems increase eciency and allow for substantial fuel savings.

Gas Valve

The gas valve senses suction from the blower, allowing gas to ow only if the gas valve is energized and combustion air is owing.

Upper Outlet Tank Sensor

This sensor monitors the upper portion water temperature (outlet) of the water heater. The control module adjusts burner ring rate so the outlet water temperature meets the set point.

Lower Inlet Tank Sensor

This sensor monitors the lower portion water temperature (inlet) of the water heater. The control module reduces or increases input, depending on how close the inlet water temperature is to the outlet water temperature set point.

Control

The integrated control system monitors upper and lower water temperature and adjusts fan speed to regulate the heater’s energy output. This allows the unit to deliver the required amount of heated energy and nothing more.

Burner

Constructed of high grade stainless steel, the burner uses pre-mixed air and gas and provides a wide range of ring rates.

Condensate Drain System

This is a condensing high eciency water heater with a condensate removal system. Condensate is nothing more than water vapor derived from combustion products, similar to that of an automobile when it is initially started. It is very important that the condensate line slopes away from the water heater and down to a suitable inside drain. If the condensate outlet on the heater is lower than the drain, us a condensate removal pump (Part # 554200, available from HTP). In addition, local authorities may require an additional condensate neutralizer to neutralize the condensate. Condensate neutralizers are made up of lime crystals, marble, or phosphate chips. Neutralizers can be installed in the eld by the installer and purchased from HTP (p/n 7450P-212). It is also very important not to expose the condensate line to freezing temperatures or any type of blockage. Plastic tubing must be the only

material used for the condensate line. Steel, brass, copper, or other materials will be subject to corrosion or deterioration. A second vent may be necessary to prevent condensate line vacuum lock on a long horizontal run. Also, an increase in pipe size may be necessary to allow condensate to drain properly. Support of the condensate line may be necessary to avoid blockage of the condensate ow.

Spark Ignition

The burner ame is ignited by applying high voltage to the system spark electrode. This causes a spark from electrode to ground.

C. Optional Equipment

Optional equipment available from HTP (and Part #):

• 3” Stainless Steel Vent Termination Kit (V1000)

• 4” Stainless Steel Vent Termination Kit (V2000)

• 3” PVC Concentric Vent Kit (KGAVT0601CVT)

• 3” Polypro Vent Kit (8400P-001)

• 3” Polypro Pipe

(33’ length # 8400P-002, 49.5’ length # 8400P-003)

• PC Connection Kit (7250P-320)

• Condensate Neutralizer (7450P-212)

• MODBUS / BACnet Adapter (7350P-636)

Part 3 - Prepare the Water Heater

Remove all sides of the shipping crate to allow the heater to be moved into its installation location.

COLD WEATHER HANDLING - If the water heater has been stored in a very cold location (BELOW 0oF) before installation, handle with care until the components come to room temperature. Failure to do so could result in damage to the water heater.

Carefully consider installation when determining heater location. Please read the entire manual before attempting installation. Failure to properly take factors such as heater venting, piping, condensate removal, and wiring into account before installation could result in wasted time, money, and possible property damage and personal injury.

A. Locating the Water Heater

These heaters are design certied for outdoor installations. Heaters must not be installed under an overhang unless clearances are in accordance with local codes, the requirements of the gas supplier / utility, and the AHJ. Three sides must remain open in the area under the overhang. Roof water drainage must be diverted away from heaters installed under overhangs. Failure of heater or components due to incorrect operating conditions IS NOT covered by product warranty.

Incorrect ambient conditions can lead to damage to the heating system and put safe operation at risk. Ensure that the installation location adheres to the information included in this manual. Failure to do so could result in property damage, serious personal injury, or death. Failure of heater or components due to incorrect operating conditions IS NOT covered by product warranty.

This water heater is heavy. Take precautions when moving the water heater into its installation location to avoid tipping, bumping, or dropping it. Failure to take such precautions may result in property damage, severe personal injury, or death.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 7

This water heater has a condensate disposal system that may freeze if exposed to sustained temperatures below 32oF. Precautions should be taken to protect the condensate trap and drain lines from sustained freezing conditions. Failure to take precautions could result in property damage, severe personal injury, or death.

1. a. Indoor Installation Area (Mechanical Room) Operating Conditions

• Ensure ambient temperatures are higher than 32oF / 0oC and lower than 140oF / 60oC

• Prevent the air from becoming contaminated by the products, places, and conditions listed in this manual

• Avoid continuously high levels of humidity

• Never close existing ventilation openings

• Ensure a minimum 1” clearance around hot water and exhaust vent pipes

b. Outdoor Installation

• Heater must be placed in an area where the exhaust plume will not be recirculated into the louver system located on the front access panel. Avoid fences or walls that extend above the exhaust vent termination. Pipe the exhaust vent so that it terminates level with or above the fence, wall, or enclosed area.

• Do not install heaters in locations where rain from building runo may spill onto the heater. Doing so could result in premature product failure. Such failures ARE NOT covered by warranty.

• Do not locate where sprinklers may spray directly onto the heater cabinet and possibly into the louvers, which could damage the control system and internal components of the water heater. Such damages ARE NOT covered by warranty.

• Do not install directly on the ground, as the water heater is heavy when lled with water. Install the heater level on a concrete pad, block, or pressure treated wood platform, designed to support the weight of the water heater and components when lled with water. The water heater must be properly supported and installed level in order to operate and drain condensate properly.

• Do not install the water heater under a deck or porch.

• Do not install the water heater in a well, stairwell, alcove, courtyard, or other recessed area.

• Do not install the water heater on stack frames.

• In areas where heater is exposed to sustained temperatures below 32oF, provisions must be made to protect the water heater, condensate lines, and piping from freezing. The use of heat tape is recommended to avoid freezing. It is also recommended to bush up the condensate line size to 1” and terminate condensate discharge line as close to the unit as possible. Longer condensate runs are more prone to freezing.

• Locate heater at least 10’ away from any forced air inlet. Maintain a clearance of at least 48” below or horizontal from any window, door, walkway, or gravity air intake. Never place heater under a porch.

• In areas where it can get extremely hot (over 100oF, it is recommended to install the heater in an area that avoids direct sunlight to keep the internal components cooler. Failure to follow this instruction could lead to premature failure. Such failures ARE NOT covered by warranty.

Figure 1 - Outdoor Installation Recommendations

2. Check for nearby connections to:

• System water piping

• Venting connections

• Gas supply piping

• Electrical power

• Condensate drain

3. Check area around heater. Remove any combustible materials, gasoline, and other ammable liquids.

When installing the heater outdoors, ensure the installation location is not near the exhaust or intake terminations of other gas-red products – boilers, water heaters, furnaces, etc. Failure to do so could result in the recirculation of exhaust fumes. Exhaust recirculation could result in a hazardous condition and cause substantial property damage, severe personal injury, or death.

This water heater must be installed upright in the vertical position as described in this manual. DO NOT attempt to install this water heater in any other orientation. Doing so will result in improper water heater operation and property damage, and could result in serious personal injury or death.

Failure to keep the water heater area clear and free of combustible materials, liquids, and vapors can result in substantial property damage, severe personal injury, or death.

The service life of the water heater’s exposed metallic surfaces, such as the casing, as well as internal surfaces, such as the heat exchanger, are directly inuenced by proximity to damp and salty marine environments. In such areas higher concentration levels of chlorides from sea spray coupled with relative humidity can lead to degradation of water heater components. In these environments, heaters must not be installed using direct vent systems which draw outdoor air for combustion. Such heaters must be installed using room air for combustion. Indoor air will have a much lower relative humidity, and hence potential corrosion will be minimized.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 8

High heat sources (generating heat 100oF / 37oC or greater, such as boiler ue pipes, space heaters, etc.) may damage plastic components of the water heater as well as plastic vent pipe materials. Such damages ARE NOT covered by warranty. It is recommended to keep a minimum clearance of 8” from high heat sources. Observe heat source manufacturer instructions, as well as local, state, provincial, and national codes, laws, regulations, and ordinances when installing this water heater and related components near high heat sources.

Locate the water heater where any leakage from the relief valve, related piping, tank, or connections will not result in damage to surrounding areas or lower oors of the building. The water heater should be located near a oor drain or installed in a drain pan. Leakage damages ARE NOT covered by warranty.

Failure of the water heater or components due to incorrect operating conditions IS NOT covered by product warranty.

4. Gas control system components must be protected from dripping water during operation and service.

5. If the heater is to replace an existing heater, check for and correct any existing system problems, such as:

• System leaks

• Location that could cause the system and heater to freeze and leak

• Incorrectly sized expansion tank

6. Clean and ush system when reinstalling a heater.

NOTE: When installing in a zero clearance location, it may not be possible to read or view some product labeling. It is recommended to make note of the heater model and serial number.

B. Leveling

Figure 2 - Minimum Service Clearances and Catch Pan Dimensions

NOTE: If you do not provide the minimum clearances shown in

Figure 2 it might not be possible to service the heater without removing it from the space.

NOTE: A combustible door or removable panel is acceptable front clearance.

In order for the condensate to properly ow out of the collection system, the area where you locate the heater must be level. Location must also fully support the weight of the lled water heater.

C. Clearances for Service Access

All water heaters eventually leak. It is recommended to install a catch pan beneath the water heater. This catch pan should be sized with a maximum depth of 2”, and a minimum diameter 2” greater than the diameter of the water heater. The catch pan should empty into an open drain line. This drain line should be 3/4” ID minimum, piped to an open drain. Failure to follow these instructions could result in property damage. Such damages ARE NOT covered by product warranty.

The space must be provided with combustion / ventilation air openings correctly sized for all other appliances located in the same space as the heater. The heater cover must be securely fastened to prevent the heater from drawing air from the heater room. This is particularly important if the heater is in a room with other appliances. Failure to comply with the above warnings could result in substantial property damage, severe personal injury, or death.

D. Residential Garage and Closet Installations

Check with your local Authority Having Jurisdiction for requirements when installing the water heater in a garage or closet. Please read the entire manual before attempting installation. Failure to properly take factors such as venting, piping, condensate removal, and wiring into account before installation could result in wasted time, money, and possible property damage and personal injury.

Precautions

If the heater is located in a residential garage, per ANSI Z223.1:

• Install the water heater burner and ignition devices a minimum of 18” above the oor of the garage. This will ensure the burner and ignition devices are well o the oor.

• When raising the water heater ensure the entire bottom and fully lled weight of the water heater are fully supported.

• Locate or protect the water heater so it cannot be damaged by a moving vehicle.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 9

The space must be provided with correctly sized combustion/ ventilation air openings for all other appliances located in the space with the water heater. For power venting installations using room air for combustion, refer to the venting section, this manual, for descriptions of conned and unconned spaces. Do not install the water heater in an attic. Failure to comply with these warnings could result in substantial property damage, severe personal injury, or death.

E. Exhaust Vent and Intake Pipe

The heater is rated ANSI Z21.10.3 Category IV (pressurized vent, likely to form condensate in the vent) and requires a special vent system designed for pressurized venting.

NOTE: The venting options described here (and further detailed in the Venting section, this manual) are the lone venting options approved for this water heater. Failure to vent the water heater in accordance with the provided venting instructions will void the warranty.

Failure to vent the water heater properly will result in serious personal injury or death.

Never obstruct the supply of combustion air to the water heater. If the water heater is installed in areas where indoor air is contaminated (see Table 2) it is imperative that the water heater be installed as direct vent so that all combustion air is taken directly from the outdoors into the water heater intake connection. Unconned space is space with volume greater than 50 cubic feet per 1,000 BTU/hr (4.8 cubic meters per kW) of the total input rating of all fuel-burning appliances installed in that space. Rooms connected directly to this space through openings not furnished with doors are considered part of the space. See Venting Section for details. Conned space is space with volume less than 50 cubic feet per 1,000 BTU/hr (4.8 cubic meters per kW) of the total input rating of all fuel-burning appliances installed in that space. Rooms connected directly to this space through openings not furnished with doors are considered part of the space. When drawing combustion air from inside a conventionally constructed building to a conned space, such space should be provided with two permanent openings: one located 6” (15 cm) below the space ceiling, the other 6” (15cm) above the space oor. Each opening should have a free area of one square inch per 1,000 BTU/hr (22cm2/kW) of the total input of all appliances in the space, but not less than 100 square inches (645cm2). If the conned space is within a building of tight construction, air for combustion must be obtained from the outdoors as outlined in the Venting section of this manual.

The exhaust discharged by this water heater may be very hot. Avoid touching or other direct contact with the exhaust gases of the vent termination assembly. Doing so could result in severe personal injury or death.

Do not attempt to vent this water heater by any means other than those described in this manual. Doing so will void the warranty and may result in severe personal injury or death.

Vents must be properly supported. Heater exhaust and intake connections are not designed to carry heavy weight. Vent support brackets must be within 1’ of the heater and the balance at 4’ intervals. Heater must be readily accessible for visual inspection for rst 3’ from the water heater. Failure to properly support vents could result in property damage, severe personal injury, or death.

1. Indoor Direct Vent of Exhaust and Intake

If installing a direct vent option, combustion air must be drawn from the outdoors directly into the water heater intake and exhaust must terminate outdoors. There are three basic direct vent options detailed in this manual: 1. Side Wall Venting, 2. Roof Venting, and 3. Unbalanced Venting. Be sure to locate the heater such that the exhaust vent and intake piping can be routed through the building and properly terminated. Dierent vent terminals can be used to simplify and eliminate multiple penetrations in the building structure (see Optional Equipment in Venting Section). The exhaust vent and intake piping lengths, routing, and termination methods must all comply with the methods and limits given in the Venting Section, this manual. When installing a combustion air intake from outdoors, care must be taken to utilize uncontaminated combustion air. To prevent

combustion air contamination, see Table 2.

2. Power Venting, Indoor Combustion Air in Conned or Unconned Space

This heater requires fresh, uncontaminated air for safe operation and must be installed in a mechanical room where there is adequate combustion and ventilating air. NOTE: To prevent combustion air contamination, see Table 2. Combustion air from the indoor space can be used if the space has adequate area or when air is provided through a duct or louver to supply sucient combustion air based on the water heater input.

When drawing combustion air from the outside into the mechanical room, care must be taken to provide adequate freeze protection.

3. Outdoor Installation

This water heater is designed to draw combustion air through the louver system in the front of the heater cabinet. Before commissioning or starting a heater installed outdoors, the end cap must be removed so that the heater draws combustion air through the louvers. This combustion air also serves to cool the internal electronics when the heater is installed in very warm climates. To prevent combustion air contamination or exhaust recirculation:

• Ensure the heater is located away from the building. Flue gas can cause damage to exterior walls and other devices.

• Locate the heater at least 48” below or horizontally from any window, door, walkway, or gravity air intake.

• Locate the heater 10’ away from any public area, outdoor sitting area, or forced air inlet.

• Locate the heater away from areas that may change over time. Do not allow the growth of trees, shrubs, or plants to obstruct proper operation of the exhaust vent system.

• If the heater is located in a fenced area, ensure the unit exhaust vent extends level with or above the top of the fence to ensure ue gas does not get trapped and possible recirculated into the louver system, which could contaminate combustion air.

See Venting section for additional details.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 10

G. Prevent Combustion Air Contamination

Install intake air piping for the heater as described in the Venting Section, this manual. Do not terminate exhaust in locations that can allow contamination of intake air.

Ensure that the intake air will not contain any of the contaminants in Table 2. Contaminated air will damage the heater, resulting in possible substantial property damage, severe personal injury, or death. For example, do not pipe intake air near a swimming pool or laundry facilities. These areas always contain contaminants.

Figure 3 - CO Warning Label

Failure to provide an adequate supply of fresh combustion air can cause poisonous ue gases to enter the living space, resulting in severe personal injury or death. To prevent combustion air contamination, see Table 2.

F. Carbon Monoxide Detectors

In the Commonwealth of Massachusetts and As Required by State and Local Codes:

Installation of Carbon Monoxide Detectors: At the time of installation or replacement of the vented gas fueled appliance, the installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor level where the gas appliance is installed, unless the appliance is located in a detached, uninhabitable structure separate from the dwelling, building, or structure used in whole or in part for residential purposes. In addition, the installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on each additional level of the dwelling, building, or structure served by the vented gas appliance. It shall be the responsibility of the property owner to secure the service of qualied licensed professionals for the installation of hard wired carbon monoxide detectors.

a. In the event that the vented gas fueled appliance is installed in a crawl space or attic, the hard wired carbon monoxide detector with alarm and battery back-up shall be installed on the next adjacent oor level. b. In the event that these requirements cannot be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Do not attempt to vent this water heater by any means other than those described in this manual. Doing so will void the warranty and may result in severe personal injury or death.

Approved Carbon Monoxide Detectors: Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 70 and be ANSI/UL 2034 listed and IAS certied.

Products to Avoid

Spray cans containing uorocarbons

Permanent wave solutions Swimming pools

Chlorinated waxes / cleaners Metal fabrication plants

Chlorine-based swimming pool chemicals

Calcium chloride used for thawing Refrigeration repair shops

Sodium chloride used for water softening

Refrigerant leaks Auto body shops

Paint or varnish removers Plastic manufacturing plants

Hydrochloric or Muriatic acid

Cements and glues New building construction

Antistatic fabric softeners used in clothes dryers

Chlorine-type bleaches, laundry detergents, and cleaning solvents

Adhesives used to fasten building products

Table 2 - Products and Areas Likely to Have Contaminants

NOTE: DAMAGE TO THE HEATER CAUSED BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY WARRANTY. (Refer to

the limited warranty for complete terms and conditions.)

Areas Likely to Have

Contaminants

Dry cleaning / laundry areas and establishments

Beauty shops

Photo processing plants

Furniture renishing areas and establishments

Remodeling areas

Garages and workshops

H. Removing a Heater from a Common Vent System

Do not install the heater into a common vent with any other appliance. This will cause ue gas spillage or appliance malfunction, resulting in possible substantial property damage, severe personal injury, or death.

Failure to follow all instructions can result in ue gas spillage and carbon monoxide emissions, causing severe personal injury or death.

When removing an existing heater, follow the steps below.

1. Seal any unused openings in the common venting system.

2. Visually inspect the venting system for proper size and horizontal pitch to determine if there is blockage, leakage, corrosion, or other deciencies that could cause an unsafe condition.

3. If practical, close all building doors, windows, and doors between the space in which the water heater remains connected to the common venting system and other spaces in the building. Turn on clothes dryers and any appliances not connected to the common

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 11

venting system. Turn on any exhaust fans, such as range hoods and bathroom exhausts, at maximum speed. Do not operate a summer exhaust fan. Close all replace dampers.

4. Place in operation the appliance being inspected. Follow the lighting instructions. Adjust the thermostat so the appliance will operate continuously.

5. Test for spillage at the draft hood relief opening after 5 minutes of main burner operation. Use the ame of a match or candle or smoke from a cigarette.

6. After it has been determined that each appliance remaining connected to the common venting system properly vents when tested as outlined, return doors, windows, exhaust fans, replace dampers, and any other gas burning appliances to their previous condition of use.

7. Any improper operation of the common venting system should be corrected to conform to the National Fuel Gas Code, ANSI Z223.1. When resizing any portion of the common venting system, the system should approach the minimum size as determined using the appropriate tables in Appendix G of ANSI Z223.1.

I. Water Chemistry Requirements

Chemical imbalance of the water supply may aect eciency and cause severe damage to the appliance and associated equipment. Water quality must be professionally analyzed to determine whether it is necessary to treat the water. Various solutions are available to adjust water quality. Adverse water quality will aect the reliability of the system. In addition, operating temperatures above 135oF will accelerate the build-up of lime scale and possibly shorten appliance service life. Failure of an appliance due to lime scale build-up, low pH, or other chemical imbalance IS NOT covered by the warranty.

The water must be potable, free of corrosive chemicals, sand, dirt, and other contaminates. It is up to the installer to ensure the water does not contain corrosive chemicals or elements that can damage the heat exchanger. Potable water is dened as drinkable water supplied from utility or well water in compliance with EPA secondary maximum contaminant levels (40 CFR Part 143.3). If the water contains contaminants higher than outlined by the EPA, water treatment is recommended and additional, more frequent maintenance may be required.

If you suspect that your water is contaminated in any way, discontinue use of the appliance and contact an authorized technician or licensed professional.

• Water pH between 6.5 and 8.5

• pH levels below 6.5 can cause an increase in the rate of corrosion. pH of 8.5 or higher can potentially cause lime scale build-up

• Maintain water pH between 6.5 and 8.5. Check with litmus paper or have it chemically analyzed by a local water treatment company.

• If the pH is not between 6.5 and 8.5, consult a local water treatment company for solutions.

• Hardness less than 7 grains (120 mg/L) (Commercial Use

- water temperatures of 140oF and greater)

• Hardness levels above the required amounts can lead to lime scale build-up throughout the system. Water below 5 grains/gallon (85 mg/L) may be over softened.

• Consult local water treatment companies for unusually hard water areas (above the required amounts) or for other treatment solutions if water is being over softened (below 5 grains/gallon [85 mg/L]).

• Chloride concentration less than 100 ppm (mg/L)

• Do not ll appliance or operate with water containing chlorides in excess of 100 ppm (mg/L).

• Using chlorinated fresh water should be acceptable as levels are typically less than 5 ppm (mg/L).

• Do not connect the appliance to directly heat swimming pool or spa water.

• Total Dissolved Solids (TDS) less than 500 ppm (mg/L)

• Total dissolved solids are minerals, salts, metals, and charged particles that are dissolved in water.

• The greater the amounts of TDS present, the higher the corrosion potential due to increased conductivity in the water.

• If using softened water to ll the appliance, it is still possible to have high TDS. This water can be corrosive. Consult local water treatment companies for other treatment solutions to reduce this eect.

*NOTE: To promote appliance service life, it is strongly recommended to follow the maintenance procedures in this manual.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 12

AIR INLET

GAS CONNECTION

CONDENSATE

PHP199-119

PHP260-119

PHP320-119

PHP399-119

LINE

MODEL A B C D E F G H J

11-3/16"

28.42 cm

MODEL

PHP199-119

PHP260-119

PHP320-119

PHP399-119

5-1/2"

13.97cm7"17.78cm

COLD WATER

INLET

1-1/2" MNPT

3.81 cm

42-1/8"

107 cm

PORT SIZES

HOT WATER

OUTLET

1-1/2" FNPT

3.81 cm

77"

195.58 cm

32"

81.28 cm

AUXILIARY VENTING GAS LINE CONDENSATE

1" MNPT

2.54 cm

85"

215.9 cm

10.16 cm

Figure 4 - Water Heater Dimensions - NOTE: All Dimensions Are Approximate

Performance Specications for Phoenix Plus Models

Temperature Rise in Degrees Fahrenheit (F) and Celsius (C)

BTU/Hr Eciency

(°F) 40 50 60 70 80 90 100 110 120 130 140

(°C) 22 28 33 39 44 50 56 61 67 72 78

199,000

260,000

95%

320,000

399,000

Table 3 - 95% Thermal Eciency Used for Calculations

GPH 579 463 386 331 289 257 232 211 193 178 165

LPH 2192 1753 1461 1253 1094 973 878 799 731 673 625

GPH 756 605 504 432 378 336 303 275 252 233 216

LPH 2862 2290 1908 1653 1431 1272 1147 1041 954 882 818

GPH 931 745 621 532 465 414 372 339 310 286 266

LPH 3524 2820 2351 2014 1760 1567 1408 1283 1174 1083 1007

GPH 1161 929 774 663 580 516 464 422 387 357 332

LPH 4395 3517 2930 2510 2196 1953 1756 1597 1465 1351 1257

Performance Equations Rated Input x .95 GPM = Temp Rise (oF) x 500 GPH = GPM x 60

EXHAUST

COLD WATER

40.64 cm

7.62 cm

INLET

16"

3/4" FNPT

1.905 cm

9-3/4"

24.76 cm

49"

124.46 cm

58-3/4"

149.22 cm

3/4" MNPT

1.905 cm

HOT WATER OUTLET

AUXILIARY

SHIPPING

WEIGHT

LBS/KG

475

215.46 kg

555

251.74 kg

575

260.82 kg

LP-454-K

10/27/14

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 13

Part 4 - Piping

Failure to follow the instructions in this section WILL VOID the warranty and may result in property damage, severe personal injury, or death.

Dielectric unions or galvanized steel ttings must not be used in a system with this water heater. Doing so WILL VOID the warranty. Use only copper, brass, or stainless steel ttings. Teon thread sealant must be used on all connections.

DO NOT pipe this water heater with black iron, galvanized steel, steel, or lead pipe. Doing so will result in premature product failure and property damage, and WILL VOID the warranty.

A. Heater Plumbing

Use two wrenches when tightening water piping at heater. Use one wrench to prevent the heater return or supply line from turning. Failure to prevent piping connections from turning could cause damage to heater components.

The heater control module uses temperature sensors to provide both high limit protection and modulating temperature control. The control module also provides low water protection by sensing the water level in the tank. Some codes / jurisdictions may require additional external controls.

Pump motors should not be supported by any type of stand due to possible misalignment of pump and motor. Failure to follow this instruction may result in property damage or personal injury.

The domestic water connections must be installed in accordance to all local and national plumbing codes, or any applicable standard which prevails. The inlet (cold) and outlet (hot) ports are 1 1/2” on all models. The water heaters are shipped with a brass drain valve located on the inside of the cabinet. The water heater is also equipped with a 1” auxiliary port that can be used as a recirculation line. The auxiliary port is located between the upper and lower combustion systems. When used, the recirculation line will increase overall heater eciency. If there is a backow preventer or any type of a no return valve in the system, install an additional tee on the cold feed line to connect to a potable hot water expansion tank. In the hot outlet, install a suitable adapter to match the copper tubing of the plumbing system. A thermal trap or heat trap loop may be installed here to provide additional energy savings and prevent the thermal siphoning of domestic hot water.

B. Auxiliary Connection

The auxiliary connection is provided to improve eciency via recirculation. This connection must be installed in accordance with all local and national codes or any applicable standard that prevails. Auxiliary connection is 1” on all models. Never use dielectric unions or galvanized steel ttings. Use only copper or brass ttings. Sealant must be used on all connections.

Never connect auxiliary connections to any system that uses glycol or other solutions formulated for hydronic systems. These auxiliary connections are to be used only in a potable water system. Failure to follow this warning could result in serious injury or death.

C. Backow Preventer

Use a backow preventer specically designed for water heater installations. This valve should be installed on the cold water ll supply line per local codes.

D. Potable Expansion Tank

A potable hot water expansion tank is required to oset heated water expansion. In most city plumbing systems, the water meter has a no return or back ow device built into the system to prevent back owing of water into city mains. Some local codes require back ow preventers on all incoming water supplies. The hot water expansion tank must be listed for potable water use. The expansion tank should be located on the cold inlet piping close to the water heater.

Expansion Tank and Make-Up Water

1. Ensure that the expansion tank is sized to correctly handle heater and system water volume and temperature.

Undersized expansion tanks cause system water to be lost from the relief valve, causing make-up water to be added. Eventual heater failure can result due to excessive make-up water addition. SUCH

FAILURE IS NOT COVERED BY WARRANTY.

The expansion tank must be suitable for hot potable water systems.

2. The expansion tank must be located as shown in Applications, this manual, or following recognized design methods. See expansion tank manufacturer’s instructions for details.

E. Temperature and Pressure Relief Valve

Overheated water and high pressures can cause water tank explosion. A properly sized temperature and pressure relief valve must be installed in the opening provided on the water heater. Failure to install a properly sized temperature and pressure relief valve could result in explosion and property damage, serious injury, or death.

To avoid water damage or scalding due to relief valve operation:

• Discharge line must be connected to relief valve outlet and run to a safe place of disposal. Terminate the discharge line in a manner that will prevent possibility of severe burns or property damage should the relief valve discharge.

• Discharge line must be as short as possible and the same size as the valve discharge connection throughout its entire length.

• Discharge line must pitch downward from the valve and terminate at least 6” above the oor drain, making discharge clearly visible.

• The discharge line shall terminate plain, not threaded, with a material serviceable for temperatures of 375oF or greater.

• Do not pipe discharge to any location where freezing could occur.

• No valve may be installed between the relief valve and heater or in the discharge line. Do not plug or place any obstruction in the discharge line.

• Test the operation of the relief valve after lling and pressurizing the system by lifting the lever. Make sure the valve discharges freely. If the valve fails to operate correctly, immediately replace with a new properly rated relief valve.

• Test T&P valve at least once annually to ensure the waterway is clear. If valve does not operate, turn the heater “o ” and call a plumber immediately.

• Take care whenever operating relief valve to avoid scalding injury or property damage.

FAILURE TO COMPLY WITH THE ABOVE GUIDELINES COULD RESULT IN FAILURE OF RELIEF VALVE OPERATION, RESULTING IN POSSIBILITY OF SUBSTANTIAL PROPERTY DAMAGE, SEVERE PERSONAL INJURY, OR DEATH.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 14

Do not thread a cap or plug into the relief valve or relief valve line under any circumstances! Explosion and property damage, serious injury, or death may result.

RE-INSPECTION OF T&P RELIEF VALVES: T&P valves should be inspected AT LEAST ONCE EVERY THREE YEARS, and replaced if necessary, by a licensed plumbing contractor or qualied service

technician to ensure that the product has not been aected by corrosive water conditions and to ensure that the valve and discharge line have not been altered or tampered with illegally. Certain naturally occuring conditions may corrode the valve and its components over time, rendering the valve inoperative. Such conditions can only be detected if the valve and its components are physically removed and inspected. Do not attempt to conduct an inspection on your own. Contact your plumbing contractor for a re-inspection to assure continued safety.

FAILURE TO RE-INSPECT THE T&P VALVE AS DIRECTED COULD RESULT IN UNSAFE TEMPERATURE AND/OR PRESSURE BUILD-UP WHICH CAN RESULT IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY, OR DEATH.

F. Scalding

This water heater can deliver scalding water. Be careful whenever using hot water to avoid scalding injury. Certain appliances such as dishwashers and automatic clothes washers may require increased water temperatures. By setting the thermostat on this heater to obtain the increased water temperature required by these appliances you may create the potential for scald injury.

To protect against injury, install a mixing valve in the water system. This valve will reduce point of use discharge temperatures by mixing cold and hot water in branch supply lines. Such valves are available from your local plumbing supplier.

Table 4 details the relationship of water temperature and time with regard to scald injury and may be used as a guide in determining the safest water temperature for your applications.

Approximate Time / Temperature Relationships in Scalds

120oF More than 5 minutes

125oF 1 1/2 to 2 minutes

130oF About 30 seconds

135oF About 10 seconds

140oF Less than 5 seconds

145oF Less than 3 seconds

150oF About 1 1/2 seconds

155oF About 1 second

Table 4 - Approximate Time / Temperature Relationships in Scalds

G. Filling the Heater

The water heater must be full of water and the system fully purged BEFORE powering the water heater. When lling the water heater, open a hot water tap to release air in the tank and piping. All air has been purged from the system when water runs freely from the faucets. Applying power to the water heater when it is not full of water will damage the heat exchanger, and could result in property damage, serious personal injury, or death. Such damages ARE NOT covered by water heater warranty.

• Make certain the drain valve is completely closed.

• Open the shut-o valve in the cold water supply line.

• Open the hot water faucets to allow air to vent from the heater and piping.

• Allow sucient time for the heater to completely ll with water.

An ASSE 1017 or ASSE 1070 temperature limiting or mixing valve is recommended in installations servicing disabled or elderly persons, or children. Mixing valves do not eliminate the risk of scalding. To avoid scalding:

• Set the water heater set point temperature as low as possible.

• Feel water before bathing or showering.

• If thermostatic valves are required, use devices specically designed for such purpose. Install these devices in accordance with instructions provided by the manufacturer.

Failure to install a temperature limiting or mixing valve and follow these instructions could result in property damage, severe personal injury, or death due to scalds.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 15

H. Applications

Figure 5 - Reverse Manifold Piping

NOTES:

1. Minimum pipe size should match connection size. Upsize pipe accordingly if greater ow is required.

2. A thermal expansion tank suitable for potable water must be sized and installed within this piping system between the backow preventer and the cold water inlet.

3. All circulators should have an integral ow check.

4. Drains and check valve between unit and storage tank will assist in purging air from system.

5. These drawings are meant to demonstrate system piping only. The installer is responsible for all equipment and detailing required by local codes. In Massachusetts, you must install a vacuum relief valve per 248 CMR.

6. Mixing valve application is optional, but recommended to help prevent scalding.

7. Always shut o power to the water heater or isolate the heater from the system if ANY plumbing work is to be done. Running the water heater without water will result in dry-ring.

The piping will not support the weight of the water heater circulator pump. Refer to the pump manufacturer’s installation instructions to properly support the circulator pump. Failure to comply with these instructions could result in substantial property damage, severe personal injury, or death.

Figure 6 - Piping with Recirculation Line and Thermostatic Mixing Valve

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 16

Exhaust

LP-179-JJ

11/30/17

Length

Greater than

Six (6) Inches

Enclosed

Space

Within First Three (3) Linear Feet of

Appliance Exhaust Vent Adapter

Part 5 - Venting

The heater must be vented as detailed in this section. Ensure exhaust vent and intake piping complies with these instructions regarding vent system. Inspect nished exhaust vent and intake piping thoroughly to ensure all joints are well secured, airtight, and comply with all applicable code requirements, as well as the instructions provided in this manual. Failure to properly install the vent system will result in severe personal injury or death.

A. General

This heater is certied as a “Category IV” appliance and requires a special venting system. The vent system will operate with a positive pressure in the pipe. Exhaust gases must be piped directly outdoors using the vent materials and rules outlined in these instructions. Do not connect vent connectors serving appliances vented by natural draft into any portion of mechanical draft systems operating under positive pressure. Follow the venting instructions carefully. Failure to do so will result in substantial property damage, severe personal injury, or death.

1. Installation should be made in accordance with the regulations of the Authority Having Jurisdiction, local code authorities, and utility companies which pertain to this type of water heating equipment.

2. Install the venting system in accordance with these instructions and with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, CAN/CGA B149, and / or applicable provisions of local building codes.

3. This water heater must be vented with materials, components, and systems listed and approved for Category IV appliances.

Exhaust and intake are to be piped separately. This heater cannot share a common exhaust or intake with multiple appliances. Failure to follow these instructions will result in substantial property damage, severe personal injury, or death.

NOTE: To avoid contamination often contained in indoor air, it is best to pipe all intake combustion air directly to the outdoors. NOTE: If exhaust vent pipe system passes through an unheated space such as an alcove or attic, the space must be heated.

Improper seating of vent pipe gaskets can cause eventual gasket failure and exhaust gas leakage. Ensure the exhaust vent pipe is properly beveled and seated before insertion into the ue adapter. Failure to do so could result in property damage, severe personal injury, or death.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Due to the extreme ammability of most glues, cements, solvents, and primers used to join plastic exhaust vent and intake pipes, explosive solvent vapors must be cleared from all vent piping before start-up. Avoid using excess cement or primer, as this may pool in the vent pipes. Vent assemblies should be allowed to cure for a period of at least 8 hours before powering a connected appliance. Failure to follow these instructions will result in substantial property damage, severe personal injury, or death. It is the installers’ responsibility to understand the hazards associated with explosive solvents and take the necessary precautions to avoid these risks.

• DO NOT insulate the rst three (3) linear feet of the exhaust vent run.

• CPVC, Polypropylene, or Stainless Steel pipe material MUST be used if the rst three (3) linear feet of the exhaust vent run is insulated or passes through an enclosed space greater than 6” in length, such as a wall.

• If CPVC is used to meet these requirements, the balance may be installed with approved PVC pipe.

• If Polypropylene or Stainless Steel is used to meet these requirements, the balance of the vent run must be installed with the same material.

• Failure to comply with this warning could result in property damage, severe personal injury, or death.

Exhaust vent adaptors are not designed as load-bearing devices, and must not be used to support exhaust vent piping. All vent pipes must be properly connected, supported, and the exhaust vent must be pitched a minimum of 1/4” per foot back to the heater to allow drainage of condensate. Failure to properly support vent piping and follow the information in this statement could result in product damage, severe personal injury, or death.

Page 17

B. Approved Materials for Exhaust Vent and Intake Pipe

Item Material

Pipe and Fittings Approved

for Intake ONLY

ABS* ANSI/ASTM D2661

PVC-DWV* ANSI/ASTM D2665

Standards for Installation In:

United States Canada

NOT PERMITTED

PVC Schedule 40/80 ANSI/ASTM D1785

Pipe Approved for

Intake OR Exhaust Vent

Pipe Fittings

Pipe Cement

Pipe Primer PVC / CPVC ASTM F656

• The exhaust and intake components installed with this boiler must be used for near boiler piping BEFORE transitioning to the approved materials listed above. DO NOT REMOVE these installed components. Doing so WILL VOID boiler warranty.

• PVC / CPVC pipe and ttings of the same diameter are considered interchangeable.

• DO NOT use Foam Core Pipe in any portion of the exhaust piping from this boiler.

• DO NOT connect PVC/CPVC to Polypropylene without an approved vent connector.

• Any transition to Polypropylene MUST be done in the vertical within ve (5) feet of the appliance.

• When installing AL29-4C vent piping, install a PVC-to-stainless adapter at the boiler vent connection, and at the termination when using a PVC termination kit. DO NOT mix AL29-4C piping from dierent manufacturers unless using adapters specically designed for the purpose by the manufacturer.

• A double wall vent may be used when using stainless steel vent material in a freezing climate.

• *ABS and PVC-DWV may be used for air intake applications ONLY. ABS is NOT PERMITTED for use in Canada.

• Contact the venting material manufacturer if there is any question about the applicability of the proposed venting material.

Failure to follow these directions will result in substantial property damage, severe personal injury, or death.

Table 5 - Approved Materials for Exhaust Vent and Intake Pipe

CPVC Schedule 40/80 ANSI/ASTM F441

Polypropylene UL-1738 or ULC-S636

Stainless Steel AL29-4C Certied for Category IV and Direct Vent Appliance Venting

PVC Schedule 40 ANSI/ASTM D2466

PVC Schedule 80 ANSI/ASTM D2467

CPVC Schedule 40 ANSI/ASTM F438

CPVC Schedule 80 ANSI/ASTM F439

ABS* ANSI/ASTM D2235 NOT PERMITTED

PVC ANSI/ASTM D2564

CPVC ANSI/ASTM F493

PVC, CPVC, and PP Venting Must be ULC-S636 Certied. IPEX is an

approved manufacturer in Canada.

PVC, CPVC, and PP Venting Must be ULC-S636 Certied. IPEX is an

approved manufacturer in Canada.

IPEX System 636 Cements and

Primers

DO NOT mix components from dierent venting systems. The vent system could fail, causing leakage of ue products into the living space. Use only the approved pipe and tting materials, and primer and cement specically designed for the material used, as listed in the above table. Failure to do so could result in property damage, serious injury, or death.

NOTE: The use of double-wall vent or insulated material for the combustion air intake pipe is recommended in cold climates to prevent the condensation of airborne moisture in the incoming combustion air.

It is required to insert the provided exhaust and intake screens into the vent terminations to prevent blockage caused by debris or birds. Failure to keep terminations clear could result in property damage, severe personal injury, or death.

You must not use “B” vent in an exhaust application. “B” vent is for intake applications ONLY. Using “B” vent in an exhaust application will result in serious injury or death.

C. Additional Requirements for Installation in Canada

1. Installations must be made with a vent pipe system certied to ULC-S636. IPEX is an approved vent manufacturer in Canada supplying vent material listed to ULC-S636. Additionally, you may use AL29-4C stainless steel venting to comply with Canadian requirements.

2. The rst three (3) feet of vent pipe from the water heater ue outlet must be readily accessible for visual inspection. 3. The components of the certied vent system must not be interchanged with other vent systems or unlisted pipe / ttings.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 18

B M

LP-179-CC

FIXED

CLOSED

OPERABLE

CLOSED

OPERABLE

FIXED

03/28/17

DETAIL

INSIDE CORNER

Exhaust Vent Terminal

Intake Pipe Terminal

Area Where Intake Terminal Is Not Permitted

D. Exhaust Vent and Intake Pipe Location

Figure 7 - Exit Terminals for Direct Vent Systems - ANSI Z223.1 / NFPA 54 for US and CAN/CSA B149.1 for Canada

DESCRIPTION US CANADA

A Clearance above grade, veranda, porch, deck, or balcony 1 foot (30 cm)

Direct Vent 1 foot

B Clearance to window or door that may be opened

Power Vent

4 ft below or to side of

opening; 1 ft above opening

C Clearance to permanently closed window *

Vertical clearance to ventilated sot located above the terminal within

a horizontal distance 2 feet (61 cm) from the center line of the terminal

E Clearance to unventilated sot *

F Clearance to outside corner *

G Clearance to inside corner *

Clearance to each side of center line extended above meter / regulator

assembly

I Clearance to service regulator vent outlet *

Clearance to nonmechanical air supply inlet to building or

the combustion air inlet to any other appliance

K Clearance to mechanical air supply inlet

Clearance above paved sidewalk or paved driveway located

on public property

M Clearance under veranda, porch deck, or balcony * 1 foot (30 cm)

Table 6 - Vent Termination Clearances - *NOTE: For clearances not specied in ANSI Z223.1 / NFPA 54 for US and CAN/CSA B149.1 for Canada, please use clearances in accordance with local installation codes and the requirements of the gas supplier.

Direct Vent 1 foot

Power Vent

4 ft below or to side of

opening; 1 ft above opening

3 feet above if within 10 feet

horizontally

Direct Vent *

Power Vent 7 feet (2.13 m)

3 feet (91 cm)

Above a regulator

within 3 feet (91 cm)

horizontally of the

vertical center line of

the regulator vent outlet

to a maximum vertical

distance of 15 ft (4.5 m)

3 feet (91 cm)

6 feet (1.83 m)

7 feet (2.13 m)

The building owner is responsible for keeping the exhaust and intake terminations free of snow, ice, or other potential blockages, as well as scheduling routing maintenance. Failure to keep the vent piping terminations clear and properly maintain the heater could result in property damage, severe personal injury, or death.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

For each oor containing bedroom(s), a carbon monoxide detector and alarm shall be placed in the living area outside the bedrooms, as well as in the room that houses the heater. Detectors and alarms shall comply with NFPA 720 (latest edition). Failure to comply with these requirements could result in product damage, severe personal injury, or death.

Page 19

E. Exhaust Vent and Intake Pipe Sizing

1. The exhaust vent and intake pipe size is 4” for all models.

2. The maximum total equivalent length of 4” exhaust vent and intake pipe should not exceed 200 feet.

a. The equivalent length of elbows, tees, and other ttings are listed in the Friction Loss Table.

Friction Loss Equivalent in Piping and Fittings

Fittings or Piping

Equivalent Feet

3” 4”

90 Degree Elbow* 5’ 3’

45 Degree Elbow 3’ 1’

Coupling 0’ 0’

Air Inlet Tee 0’ 0’

Straight Pipe 1’ 1’

Concentric Kit 3’ N/A

V500 2” Kit N/A N/A

V1000 3” Kit 1’ 1’

V2000 4” Kit 1’ 1’

Table 7 - *Friction loss for long radius elbow is 1 foot less. NOTE: Consult Polypropylene venting instructions for friction loss and pressure drop equivalents.

b. For example: If exhaust vent has two 90o elbows and 10 feet of PVC pipe we will calculate: Exhaust Vent Equivalent Length = (2x3) + 10 = 16 feet. Further, if the intake pipe has two 90o elbows, one 45o elbow, and 10 feet of PVC pipe, the following calculation applies: Intake Pipe Equivalent Length = (2x3) + 1 + 10 = 17 feet. Total Equivalent Length = 16 + 17 = 33 feet. The total equivalent length is 33 feet, well below the maximum of 200 feet. c. Eort should be made to keep a minimum dierence in equivalent length between the exhaust vent and intake pipe. d. The vent size on the PHP199-119 can also be reduced down to a 3” vent from a 4” vent in order to accommodate existing vent sizes. When reducing down to a 3” vent from a 4” vent on PHP199-119 models, the total length shall not exceed 100 equivalent feet. Vent reduction must begin at the heater.

3. The minimum total equivalent length is 16 feet.

Do not reduce the vent size on any model other than the PHP199-

119. Doing so could result in water heater shutdown and property damage.

Do not exceed the maximum lengths for vent pipes. Excessive length could result in heater shutdown and property damage.

Failure to provide a minimum total vent length of 16 equivalent feet could result in property damage and improper product operation.

F. Exhaust Vent and Intake Pipe Installation

All joints of positive pressure vent systems must be sealed completely to prevent leakage of ue products into the living space. Failure to do so could result in property damage, serious injury, or death.

NOTE: Do not block any air openings in the cabinet to ensure proper cooling and ventilation of components.

When venting in an Indoor Installation: Remove cap installed outside the water heater cabinet from the air intake and leave the

cap inside the water heater cabinet installed. When venting in an Outdoor Installation: Remove cap from the air intake inside the water heater and leave the cap outside the water heater installed. See Figure 8 for details. Failure to do so could result in property damage, serious injury, or death.

Figure 8 - Air Intake Instructions

1. Use only solid PVC, CPVC, or stainless steel pipe or a Polypropylene vent system approved for use with Category IV appliances. FOAM CORE PIPING IS NOT APPROVED FOR EXHAUST VENT APPLICATIONS. Foam core piping may be used on air inlet piping only.

2. Remove all burrs and debris from joints and ttings.

3. When using PVC or CPVC pipe, all joints must be properly cleaned, primed, and cemented. Use only cement and primer approved for use with the pipe material. Cement must conform to ASTM D2564 for PVC and ASTM F493 for CPVC pipe. NOTE: DO NOT CEMENT

POLYPROPYLENE PIPE.

4. Ensure the vent is located where it will not be exposed to prevailing winds.

5. In all roof venting applications, exhaust discharge must point away from the pitch of the roof.

6. If the exhaust vent is to be terminated in a walled o area (such as a roof with a parapet wall), ensure the exhaust vent terminates a minimum of 10’ from nearest wall and extends level with or above the top of the wall. This will ensure ue gas does does not get trapped and possibly recirculated into the intake air pipe, which could contaminate the combustion air.

7. To prevent water leakage, install adequate roof ashing where the pipe enters the roof.

8. Do not locate vent over public walkways, driveways, or parking lots. Condensate could drip and freeze, resulting in a slip hazard or damage to vehicles and machinery.

9. Due to potential moisture build-up, sidewall venting may not be the preferred venting option. To save time and cost, carefully consider venting installation and location.

10. Horizontal lengths of exhaust vent must slope back towards the water heater not less than ¼” per foot to allow condensate to drain from the vent pipe.

11. The exhaust vent must terminate where vapors cannot make

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 20

accidental contact with people or pets, or damage air conditioners, shrubs, or other plants or objects.

12. DO NOT vent the water heater in a chimney ue serving a separate appliance designed to burn solid fuel. The water heater may only be vented in vacant chimneys. In vacant chimney applications, install and seal a rain cap over existing chimney openings.

13. All piping must be fully supported. Use pipe hangers at a minimum of 4 foot intervals to prevent sagging of the pipe where condensate may form.

14. Do not use the heater to support any piping.

15. A screened straight coupling is provided with the heater for use as an outside exhaust termination.

16. A screened inlet air tee is provided with the heater to be used as an outside intake termination.

17. Maximum Snow Level Determination: These installation instructions reference snow levels in establishing a minimum height for the installation of exhaust vent or air intake terminations. Snow levels shall be determined as follows:

a. The installation location may, by ordinance, designate how snow levels are calculated in that location; or b. In the absence of specic ordinances, snow levels shall be calculated from the average monthly maximum depth of snow accumulation as indicated by the National Weather Service’s 10 year statistics for the installation location/geographical area.

In addition:

• Total length of vent piping shall not exceed the limits specied in this manual.

• The vent piping for this direct vented appliance is approved for zero clearance to combustible construction.

• The ue products coming from the exhaust vent will create a large plume when the heater is in operation. Avoid venting in areas that will aect neighboring buildings or be considered objectionable.

• DO NOT locate exhaust vent or intake pipe in a parking area where machinery may damage the pipe.

• DO NOT vent near sot vents, crawl space vents, or other areas where condensate or vapor could create a nuisance or hazard or cause property damage.

• DO NOT vent where condensate vapor could cause damage or could be detrimental to the operation of regulators, relief valve, or other equipment.

In the Commonwealth of Massachusetts and as Required by State and Local Codes:

The vented gas fueled appliance shall not be installed so its combustion, ventilation, or dilution air is obtained from a bedroom or bathroom. Signage: Whenever any through-the-wall (horizontal or sidewall) vent is installed less than seven feet above the nished grade, a metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight feet above grade directly in line with the exhaust vent terminal. The sign shall read, in print no less than 0.5 inches in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”. Marking of Exhaust Vent and Intake Pipe: Piping used for ventilation, make-up, or combustion air intake shall be labeled as follows:

a. Throughout the entire developed length:

i. Labels must be placed every ten feet for exposed/visible piping; or

ii. Labels must be placed every three feet for concealed piping. b. At all changes of direction; c. On each side of a penetration through a partition, wall or ceiling; and d. The labels shall be black lettering that:

i. Indicates that the piping is used for ventilation, make-up, or

combustion air intake, and

ii. The letters shall be sized equal to a minimum of the pipe diameter.

However, for piping with a diameter exceeding two inches, said

lettering does not need to be larger than two inches.

The following table lists optional exhaust/intake terminations available

from HTP:

Description Stock Code

3” PVC Concentric Termination Kit KGAVT0601CVT

3” Stainless Steel Termination Kit V1000

4” Stainless Steel Termination Kit V2000

3” Polypro Vent Kit 8400P-001

Table 8 - Optional Vent Kits

G. Applications

1. Indoor Direct Vent Installation of Exhaust and Intake

If installing a direct vent option, combustion air must be drawn from the outdoors directly into the water heater intake, and exhaust must terminate outside. There are three basic direct vent options detailed in this manual: 1. Side Wall Venting, 2. Roof Venting, and 3. Unbalanced Venting. Be sure to locate the heater such that the exhaust vent and intake pipe can be routed through the building and properly terminated. Dierent vent terminals can be used to simplify and eliminate multiple penetrations in the building structure (see Optional Equipment in Venting Section). The exhaust vent and intake pipe lengths, routing and termination methods must all comply with the methods and limits given in the Venting section of this manual. When installing a combustion air intake from outdoors, care must be taken to utilize uncontaminated combustion air. NOTE: To prevent combustion air contamination, see Table 2.

Take extra precaution to adequately support the weight of vent pipes terminating through the roof. Failure to properly support roof terminated piping could result in property damage, serious injury, or death.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 21

6/23/15

SIDEWALL VENTING WITH TEE (INTAKE) AND EXHAUST

2” PIPE 3” PIPE

Sidewall Venting with Kit

Sidewall Venting with Concentric Vent Kit

Roof Venting with Concentric Vent Kit

Figure 9 - Two Pipe Roof and Sidewall Venting with Included Equipment (Tee and Coupling)

NOTE: When installing two pipe sidewall venting, terminate 2”

exhaust vent pipe with a 90o elbow, and 3” exhaust vent pipe with a 45o elbow. Failure to do so will result in improper appliance operation.

Figure 10 - Venting with Optional Kits (NOT INCLUDED WITH THE WATER HEATER)

NOTE: These drawings are meant to demonstrate system venting only.

The installer is responsible for all equipment and detailing required by local codes.

All vent pipes must be glued, properly supported, and the exhaust pitched a minimum of 1/4” per foot back to the heater to allow drainage of condensate. When placing support brackets on vent piping, the rst bracket must be within 1 foot of the water heater and the balance of 4 foot intervals on the vent pipe. Venting must be readily accessible for visual inspection from the rst three feet from the heater.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 22

SIDE VIEW

FRONT VIEW

Intake

Exhaust

FRONT VIEW

SIDE VIEW

LP-325-PP 03/03/11

UNBALANCED VENTING

Figure 11 - Horizontal (Snorkel) Venting

NOTES:

A. For every 1” of overhang, the exhaust vent must be located 1” vertical below overhang (overhang means top of building structure and not two adjacent walls [corner of building]). B. Typical installations require 12” minimum separation between bottom of exhaust outlet and top of air intake. C. Maintain 12” minimum clearance above highest anticipated snow level or grade (whichever is greater). D. Minimum 12” between vents when installing multiple vents. E. 12” minimum beyond air intake.

Figure 12 - Unbalanced Venting - Roof Exhaust and Sidewall Intake

NOTE: These drawings are meant to demonstrate system venting only.

The installer is responsible for all equipment and detailing required by local codes.

2. Venting Through an Existing System

This heater may be vented through an existing unused vent system. The inner diameter of the existing vent system is utilized for the combustion air source. Two methods have been approved for such venting: Concentric Venting Through an Existing System and Venting as a Chase.

Vent / Air Inlet Size Minimum Existing Vent / Chase Size

3” 5”

4” 7”

Table 9 - Minimum Existing Vent / Chase Sizing

Do not install the heater into a common existing vent with any other appliance. This will cause ue gas spillage or heater malfunction, resulting in substantial property damage, serious personal injury, or death.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 23

AIR INTAKE W/ SCREEN

Exhaust

Intake

Concentric Venting Through an Existing System 1

Exhaust

Intake

Concentric Venting Through an Existing System 2

Exhaust

Intake

AIR INTAKE W/ SCREEN

EXISTING VENT

INTAKE

Chase Venting Through an Existing System 3

Intake

Exhaust

Contractors must check state and local codes before installing through an existing vent opening. State and local codes always take precedence over manufacturer’s instructions. Failure to check state and local codes before installing through an existing opening could result in property damage and add signicantly to installation costs.

If an existing venting system is converted for use with this heater, the installer must ensure that the existing venting system is clean and free from particulate contamination that could damage the heater. Failure to do so could result in property damage and heater failure. Such failure IS NOT covered under warranty.

Concentric Venting Through an Existing System

NOTE: The following instructions refer only to venting through an existing vent system, and not to venting with HTP’s optional concentric vent kits. Refer to Concentric Vent Kit installation manual (LP-166) for further information on venting with the optional concentric vent kits. Concentric venting through an existing system must run vertically through the roof. Use only the approved venting materials specied in Table 5 for piping the system. All instructions listed in this Venting section apply. See Figures 13-1 and 13-2 for venting demonstrations.

The upper and lower vent terminations as well as all joints in the venting system must be properly sealed to ensure that all combustion air is drawn properly and exhaust does not leak from the system. Failure to properly seal the venting system will result in property damage, serious personal injury, or death.

Chase Venting Through an Existing System

When venting as a chase, follow all instructions included in this Venting section, including those in the previous Concentric Venting Through an Existing System section. See Figure 13-3 for chase venting demonstration.

3. Power Venting, Indoor Combustion Air in Conned or Unconned Space

This heater requires fresh, uncontaminated air for safe operation and must be installed in a mechanical room where there is adequate combustion and ventilating air. NOTE: To prevent combustion air

contamination, see Table 2.

Combustion air from the indoor space can be used if the space has adequate area or when air is provided through a duct or louver to supply sucient combustion air based on the water heater input.

Never obstruct the supply of combustion air to the water heater. If the water heater is installed in areas where indoor air is

contaminated (see Figure 14) it is imperative that the water heater be installed as direct vent so that all combustion air is taken directly from the outdoors into the water heater intake connection. Unconned space is space with volume greater than 50 cubic feet per 1,000 Btu/hour (4.8 cubic meters per kW) of the total input rating of all fuel-burning appliances installed in that space. Rooms connected directly to this space, through openings not furnished with doors, are considered part of the space. Conned space is space with volume less than 50 cubic feet per 1,000 Btu/hour (4.8 cubic meters per kW) of the total input rating of all fuel-burning appliances installed in that space. Rooms connected directly to this space, through openings not furnished with doors, are considered part of the space. When drawing combustion air from inside a conventionally constructed building to a conned space, such space should be provided with two permanent openings: one located 6” (15 cm) below the space ceiling, the other 6” (15cm) above the space oor. Each opening should have a free area of one square inch per 1,000 Btu/hr (22cm2/kW) of the total input of all appliances in the space, but not less than 100 square inches (645cm2). If the conned space is within a building of tight construction, air for combustion must be obtained from the outdoors as outlined in the Venting section of this manual. See Figure 15.

Figure 13 - 1, 2 - Concentric Venting Through an Existing System, 3, Chase Venting Through an Existing System

NOTE: These drawings are meant to demonstrate system venting only. The installer is responsible for all equipment and detailing required

by local codes.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 24

LP-325-X

DO NOT PLACE DRYER NEAR WATER HEATER OR BOILER

BOILER OR

HEATER

INDOOR COMBUSTION AIR (SINGLE PIPE)

OUTDOOR COMBUSTION AIR (SINGLE PIPE)

BOILER

HEATER

Figure 14 - Do Not Place Appliance Near Dryer

Figure 15 - Indoor and Outdoor Combustion Air - Single Pipe

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 25

4. Outdoor Installation

When drawing combustion air from the outdoors, care must be taken to provide adequate freeze protection. Failure to do so could result in property damage and premature product failure. Such damages and failures ARE NOT covered by product warranty.

This water heater is designed to draw combustion air through the louver system in the front of the heater cabinet. Before starting a heater installed outdoors, the end cap must be removed so that the heater draws combustion air through the louvers. This combustion air also serves to cool the internal electronics when the heater is installed in very warm climates. To prevent combustion air contamination or exhaust recirculation:

• Ensure the heater is located away from the building. Flue gas can cause damage to exterior walls and other devices.

• Locate the heater at least 48” below or horizontally from any window, door, walkway, or gravity air intake.

• Locate the heater 10’ away from any public area, outdoor sitting area, or forced air inlet.

• Locate the heater away from areas that may change over time. Do not allow the growth of trees, shrubs, or plants to obstruct proper operation of the exhaust vent system.

• If the heater is located in a fenced area, ensure the unit exhaust extends level with or above the top of the fence to ensure ue gas does not get trapped and possibly recirculated into the louver system, which could contaminate the combustion air.

Figure 16 - Recommended Outdoor Installation Clearances

Figure 17 - Recommended Outdoor Enclosure

Figure 18 - Outdoor Enclosure with Overhang

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 26

Part 6 - Condensate Removal

NOTE: Check with your local gas company to determine if combustion

condensate disposal is permitted in your area. In the state of Massachusetts, condensate must be neutralized before entering a drain. This condensing high eciency water heater has a condensate removal system. Condensate is water vapor derived from combustion products, similar to that produced by an automobile when it is initially started. It is very important that the condensate line is sloped down away from the heater and to a suitable drain. If the heater condensate outlet is lower than the drain, you must use a condensate removal pump (kit p/n 554200 available from HTP). If required by local authorities, a condensate lter of lime crystals, marble, or phosphate chips will neutralize slightly acidic condensate. This can be installed in the eld and purchased from HTP (p/n 7450P-212).

The condensate line must remain unobstructed. If allowed to freeze in the line or obstructed in any other manner, condensate can exit from the water heater tee, resulting in potential water damage to property. When installing a condensate pump, select one approved for use with condensing heaters and furnaces. The condensate pump should have an overow switch to prevent property damage from spillage. Condensate from the heater will be slightly acidic (pH from

3.2 to 4.5). Install a neutralizing lter if required by local codes.

Power to the optional condensate pump is continuous. When the water heater is powered o the condensate pump will remain on. It is important to remember to turn o the condensate pump when powering down the water heater. Failure to do so could result in property damage, severe personal injury, or death.

Figure 19 - Condensate Piping

NOTES:

1. Condensate line must be pitched at least ¼” per foot to properly drain. If this cannot be done, or a very long length of condensate hose is used, increase the condensate line to a minimum of 1” ID and place a tee in the line after the condensate neutralizer to properly reduce vacuum lock in the drain line.

2. PVC or CPVC pipe should be the only material used for condensate line. Steel, brass, copper, and other metals will be subject to corrosion or deterioration.

3. A frozen condensate line could result in a blocked vent condition. It is very important to protect the condensate line from freezing temperatures or any type of blockage. In installations that may encounter sustained freezing conditions, the use of heat tape is recommended to avoid freezing of the condensate line. It is also recommended to bush up the condensate line size to 1” and terminate condensate discharge as close to the unit as possible. Longer condensate runs are more prone to freezing. Damages due to frozen or blocked condensate lines ARE NOT covered by warranty.

4. Support of the condensate line may be necessary to avoid blockage of the condensate ow.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 27

Part 7 - Wiring

To avoid electrical shock, turn o all power to the heater prior to opening an electrical box within the unit. Ensure the power remains o while any wiring connections are being made. Failure to follow these instructions could result in component or product failure, serious injury, or death. Such product failure IS NOT covered by warranty.

Jumping out control circuits or components WILL VOID product warranty and can result in property damage, personal injury, or death.

A. Line Voltage Input

The heater must be wired to a 120 volt circuit by a qualied electrician. It is recommended that the heater be wired on its own circuit to minimize the possibility of circuit failure due to outside clauses. The heater requires a maximum of 8 amps at 120 volts in use. NOTE: The current draw listed on the rating plate does not include circulator current.

B. Line Voltage Condensate Output

The heater has the capability of supplying power to a condensate pump. The connection is 120 VAC +/- 10% at a max of 2 amps. Power is supplied to the pump only when the heater is connected to power, and the power switch is in the on position.

It is of extreme importance that this unit be properly grounded. It is very important that the building system ground is inspected by a qualied electrician prior to making this connection. Electrical power must only be turned on when the heater is completely lled with cold water. Failure to follow these instructions could result in component or product failure, serious injury, or death.

Figure 20 - Line Voltage Wiring

Label all wires prior to disconnecting them when servicing the heater. Wiring errors can cause improper and dangerous operation. Failure to follow these instructions may result in property damage or personal injury.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 28

C. Internal Wiring Diagram

Figure 21 - Stage 1 Wiring Diagram

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 29

Figure 22 - Stage 2 Wiring Diagram - Not Applicable to 199kBTU Models

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 30

11/26/14

Figure 23 - Control Board Wiring

Part 8 - Gas Connections

Failure to follow all precautions could result in re, explosion, severe injury, or death.

Ensure the gas on which the water heater will operate is the same type specied on the rating plate. Failure to do so could result in water heater malfunction, property damage, personal injury, or death.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

The gas supply shall have a minimum of no less than 3.5” water column, a maximum inlet pressure of no greater than 14” water column (350 mm), and ½ pound pressure (3.5 kPa). The entire piping system, gas meter, and regulator must be sized properly to prevent excessive pressure drop (greater than 0.5” WC) as stated in the National Fuel Gas Code. This information is listed on the rating plate. It is very important that the water heater is connected to the gas type noted on the rating plate: “LP” for liqueed petroleum, propane gas, or “Nat” for natural or city gas. All gas connections must be approved by the local gas supplier or utility, in addition to the governing authority, prior to turning the gas supply on.

Page 31

Do not remove the adaptor in Figure 24! It is mandatory that this tting is used for connection to a eld fabricated drip leg per the National Fuel Gas Code. You must ensure that the entire gas line to the connection at the appliance is no smaller than 3/4”. If the water heater experiences a pressure drop greater than 1” WC, the meter, regulator, or gas line is undersized or in need of service. A manometer can be attached to the incoming gas drip leg by removing the cap. The gas pressure must remain between 3.5” and 14” WC during stand-by (static) mode and while in operating (dynamic) mode at full output. If an in-line regulator is used, it must be installed a minimum of 10 feet from the heater. It is very important that the gas line is properly purged by the gas supplier or utility. Improper line sizing or failure to properly purge the lines will result in ignition failure. This problem is especially noticeable in NEW LP installations, in empty tank situations, or when a utility company shuts o service to an area to maintain supply lines. Once all inspections have been performed, the piping must be leak tested. If the leak test requirement is a higher test pressure than the maximum gas inlet pressure, isolate the heater from the gas line to continue leak testing. To do this, turn o the factory and eldinstalled gas cocks. Failure to do so may damage the gas valve. In the event the gas valve is exposed to a pressure greater than ½ PSI, 14” water column, the gas valve must be replaced. The gas valve must not be replaced with a conventional gas valve under any circumstances. As an additional safety feature, the gas valve in this water heater has a anged connection to the swirl plate and blower.

Figure 24 - Gas Connection

UL recognized fuel gas detectors are recommended in all enclosed propane and natural gas applications where there is a potential for an explosive mixture of fuel gas to accumulate. The installation of these detectors should be made in accordance with the detector manufacturer’s recommendations, and/or local laws. Failure to install fuel gas detectors in these applications could result in re, explosion, property damage, severe personal injury, or death.

A. Gas Pipe Sizing Tables

1. Gas Pipe Sizing

This information is for reference use only. Refer to gas pipe manufacturer specications for actual delivery capacity. The DOE standard for Natural Gas is 1100 BTU/ft3. Contact the local gas supplier for actual BTU/ft3 rating.

2. Natural Gas Pipe Sizing

The following table lists maximum capacity of pipe in cubic feet of gas per hour for gas pressures of 14” or less and a pressure drop of

0.5 inches water column, based on a 0.60 specic gravity for natural gas.

3. LP (Liquid Propane) Gas Pipe Sizing

Contact gas supplier to size pipes, tanks, and 100% lockup gas pressure regulator. Adjust propane supply regulator provided by the gas supplier for 14 inches w.c. maximum pressure.

Pipe Size (in.)

3/4 360 247 199

1 678 466 374 320 284 257 220

1 1/4 1390 957 768 657 583 528 452 400 322 275

1 1/2 2090 1430 1150 985 873 791 677 600 482 412

2 4020 2760 2220 1900 1680 1520 1300 1160 928 794

3 11300 7780 6250 5350 4740 4290 3670 3260 2610 2240

4 23100 15900 12700 10900 9660 8760 7490 6640 5330 4560

Table 10 - Source - ANSI Z223.1

10 20 30 40 50 60 80 100 150 200

Length of Pipe (Feet)

B. Gas Piping Requirements

Support gas supply piping with hangers, not by the heater or its accessories. The heater gas valve and blower will not support the weight of the piping. Make sure the gas piping is protected from physical damage and freezing, where required. Failure to follow these instructions could result in gas leakage, re, explosion, property damage, severe personal injury, or death.

Do not use Teon tape on gas line pipe thread. Use a pipe compound rated for use with natural and propane gases. Apply sparingly on male pipe ends, leaving the two end threads bare. Failure to follow these instructions could result in gas leakage, re, explosion, property damage, severe personal injury, or death.

BTU’s Per

Hour x 1,000

Schedule 40

Metallic Pipe

(0.60 Specic

Gravity,

0.5 WC

Pressure Drop)

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 32

1. The gas adapter tting on the water heater is 3/4” NPT. NOTE: The gas supply pipe size must not be less than 3/4”.

2. The supply line must be sized for the maximum output of the water heater being installed. If there are additional gas appliances on the main supply line, size the supply line for the maximum total COMBINED BTU/Hr draw of the appliances. This will ensure the supply line is sized to allow all the appliances to operate at the same time.

3. Measure the length of the gas supply line from the gas meter to the water heater. The water heater must be installed downstream of the gas meter to ensure adequate gas supply.

4. Use the table in this manual or refer to the gas line manufacturer’s sizing information to determine the correct supply pipe size. Run the gas supply line in accordance with all applicable codes.

5. The National Fuel Gas Code (NFPA 54) requires that a sediment trap (drip leg) be installed in the gas line on appliances not so equipped. The drip leg must be accessible, a minimum of 3” in length, and not subject to freezing conditions. See Figure 25.

6. A manual gas shut-o valve should be installed in the gas supply line close to the water heater. Locate and install manual shuto valves in accordance with local and state requirements.

7. To facilitate any future maintenance, it is also recommended that an approved gas union tting be installed in the supply line between the shut-o valve and the 1/2” NPT connection on the water heater.

8. Use a manometer to test the gas pressure to make sure it meets the minimum standards and does not exceed the maximum standards of the water heater.

9. Leak test the gas line pipe before placing the water heater in operation. Only use approved leak detector liquid solutions to check for leaks. Never use an open ame to check for leaks.

C. Gas Valve

Do not do a gas conversion on this appliance without an ocially approved conversion kit and instructions supplied by HTP. Failure to use a conversion kit when converting the appliance to re on Natural or Propane gas will result in extremely dangerous burner operation, leading to re, explosion, severe personal injury, or death.

Strain on the gas valve and ttings may result in vibration, premature component failure and gas leakage, and result in re, explosion, property damage, severe personal injury, or death.

Adjustments to the throttle screw or oset may only be made by a qualied gas technician using a calibrated combustion analyzer capable of measuring CO2 and CO. Failure to follow this instruction could result in re, explosion, property damage, severe personal injury, or death.

D. Checking Gas Pressure at the Water Heater for Proper Operation

NOTE: Refer to Figure 25 when checking gas pressure.

1. The water heater and its individual shuto valve must be disconnected from the gas supply piping system during any pressure testing of the system at pressures greater than ½ psi (3.5 kPa).

2. The water heater must be isolated from the gas supply piping system by closing its individual manual shuto valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa). Loosen the screw on the pressure tap inlet to attach a manometer and check the gas inlet pressure. The minimum and maximum inlet gas line pressures must meet the requirements shown in Table 11.

Natural or LP Gas

Minimum Pressure 3.5” WC

Maximum Pressure 14”WC

Table 11 - Gas Pressure Requirements

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Figure 25 - Gas Valve

Page 33

Do not re (operate) the water heater until all connections have been completed and the heat exchanger is lled with water. Doing so will damage the water heater and void the warranty.

Part 9 - Start-Up Procedure

FOR YOUR OWN SAFETY READ BEFORE OPERATING

1. This water heater does not have a pilot. It is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand.

2. BEFORE OPERATING: Smell all around the water heater area for gas. Be sure to smell next to the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any water heater.

• Do not touch any electric switch, do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas suppliers’ instructions.

• If you cannot reach your gas supplier, call the re department.

• Turn o the gas shuto valve (located outside the water heater) so that the handle is crosswise to the gas pipe. If the handle will not turn by hand, don’t try to force or repair it, call a qualied service technician. Force or attempted repair may result in a re or explosion.

4. Do not use this water heater if any part has been under water. Immediately call a qualied service technician to inspect the water heater and to replace any part of the control system and any gas control that has been damaged.

5. The water heater shall be installed so the gas ignition system components are protected from water (dripping, spraying, rain, etc.) during water heater operation and service (circulator replacement, condensate trap, control replacement, etc.)

Failure to follow these instructions could result in property

damage, serious personal injury, or death.

A. Operating Instructions

If you smell gas, STOP. Follow listed safety instructions above. If you do not smell gas, follow the next steps.

1. Make sure tank is full with cold water and purge all piping. To assure adequate piping, open all hot water faucets.

Ensure the water heater is full of water before ring the burner. Failure to do so will damage the heater. Such damage IS NOT covered by warranty, and could result in property damage, serious personal injury, or death.

2. Turn on all electric power to water heater.

3. Adjust the temperature set point of the heater to the desired level. The factory default setting is 119oF. If changes are necessary, follow “Overall Water Heater and Control Operation” in this section.

4. If the water heater fails to start, refer to the Troubleshooting section in the back of this manual.

B. Overall Water Heater and Control Operation

These water heaters have two control systems: one to regulate the bottom combustion system, and one to regulate the top.* To adjust the temperature of stored water, press and hold S3 for 2 seconds. The rst item is DU: Water Temperature Set Point - factory set at 119oF. Adjust down by pressing S1 to a temperature as low as 95oF. Adjust up as high as 160oF by pressing S2. Press S3 again to

display DH: Dierential, which is factory set at 7oF and adjustable down to1oF by pressing S1 and up to 18oF by pressing S2. NOTE: Due to the highly advanced control on this water heater, which compensates for varying inlet water temperature, the actual dierential temperature may vary slightly from the setting. Press S3 again to display the factory default temperature measurement in Fahrenheit. Change the default to Celsius by pressing S1. When nished, press S3 one nal time to place unit back in operation. The control automatically restarts if no key is pressed for 2 minutes. To increase system eciency, it is advised to set the top control at a higher temperature (125oF for example), and the bottom control at a lower temperature (110oF). This allows the water heater to stage the combustion systems.

*NOTE: PHP199-119 models have one combustion and control system.

C. Status Menu

Installers are also able to check the current status of the heater parameters by pressing S4 for 3 seconds. Once activated, the display will show d1 alternating with the actual upper supply tank temperature. Actual values are displayed for each function. To view the next value, simply press S4 to go to the next displayed value. Listed below are the values which can be displayed. These values cannot be changed. To exit this menu, press S3 to resume normal operation.

Function Value

d1 Actual temperature from upper tank sensor

d2 Actual temperature from lower tank sensor

d3 0 - Not Used

d4 308 - Not Used

d5 Outdoor Sensor

d8 0 - Not Used

d9 1 - Not Used

d10

d11 32 - Not Used

d12

d13

d14 0 - Not Used

d15 Passed ignition attempts in thousands

Table 12 - Status Menu Functions and Values

Actual Fan Speed divided by 10 (Example: If fan speed

displayed is 410 x 10 = 4100 RPM actual fan speed)

Actual Ionization Current read from ame rectication

probe

Actual status of bus communication - co = connected,

nc = not connected

Power on hours in thousands (display will not read

until 100 hours)

Total water heating hours in thousands (display will

not read until 100 hours)

D. Test Mode

This function is intended to simplify gas valve adjustment if necessary. Listed on the following page are recommended limits on each heater and the combustion settings. Automatic modulation does not take place when the controller is in Test Mode, only temperature limitation based on the heater set point. Fan speed can be increased or decreased by pressing either S1 or S2. To activate Test Mode, press S2 and S3 simultaneously for 1 second. Once activated, Ser will display and alternate with the actual fan speed. The measurement of the combustion levels should always be taken at the highest and lowest fan speed. When in Test Mode, the heater’s limit will shut down the burner if temperature limit is exceeded. It is recommended to draw water out of the tank to lower temperature so tests can be performed. After 10 minutes, Test Mode stops automatically. To exit Test Mode, press S1 and S2 simultaneously for 1 second.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 34

Combustion Settings on All Models

Fan Speed

Carbon

Monoxide

(CO) PPM

Carbon Dioxide

(CO2) %

Table 13 - NOTE: Low Fire CO2 Shall be Equal to or Less Than .5% of the High Fire Measurement

Ignition issues may result if Low Fire CO2 measures greater than .5% of the High Fire Measurement.

BTU Ignition Min Max

199,000*

199,000 D Model

260,000 7600

320,000

399,000 9800

Table 14 - *Model has a Single Combustion System

Natural Gas (NG) Propane (LP)

Low Ignition High Low Ignition High

1-10 2-15 2-20 1-10 2-15 2-20

8-10 8 1/2- 10 1/2 9-11

Fan Speeds

2200 9800

5850

7800

3000

2000

2200

E. Maintenance

The control system requires no periodic maintenance under normal conditions. However, in unusually dirty or dusty conditions, periodic vacuuming of the cover to maintain visibility of the display and indicators is recommended. In dirty environments, such as construction sites, care must be taken to keep the water heater burner cover in place and drywall or saw dust away from water heater.

In unusually dirty or dusty conditions care must be taken to keep water heater burner door in place. Failure to do so VOIDS warranty.

Allowing the heater to operate with a dirty combustion chamber will hurt operation. Failure to clean the heat exchanger as needed by the installation location could result in heater failure, property damage, personal injury, or death. Such product failures ARE NOT covered under warranty.

Part 10 - Shutdown

A. Shutdown Procedure

If the burner is not operating, disconnect the electrical supply. If the burner is operating, lower the set point value to 70oF and wait for the burner to shut o. Continue to wait for the combustion blower to stop, so all latent combustion gases are purged from the system. This should take a maximum of 40 to 90 seconds. After combustion gases are purged turn o electrical power to the water heater.

B. Vacation Procedure

If there is danger of freezing, change the set point to 70oF. DO NOT turn o electrical power. If there is no danger of freezing, follow “Shutdown Procedure”.

C. Failure to Operate

Should the burner fail to light, the control will perform two more ignition trials prior to entering a lockout state. Note that each subsequent ignition trial will not occur immediately. After a failed ignition trial, the blower must run for approximately 10 seconds to purge the system. Therefore, a time period of approximately 40 to 90

seconds will expire between each ignition trial. If the burner lights during any one of these three ignition trials, normal operation will resume. If the burner lights, but goes o in about 4 seconds, check the polarity of the wiring. See electrical connection section of this manual. If the burner does not light after the third ignition trial, the control will enter a lockout state. This lockout state indicates that a problem exists with the water heater, the controls, or the gas supply. Under such circumstances, a qualied service technician should be contacted immediately to properly service the water heater and correct the problem. If a technician is not available, pressing the S4 button will remove the lockout state so additional trials for ignition can be performed. The unit will try to relight once every 6 minutes.

D. Important Notice

It is extremely important that whenever work is performed on the plumbing system that either:

• The water heater is powered o, or,

• The water heater is valved o and isolated from the plumbing system.

Failure to take these measures could result in a dry-ring condition.

Resistance Table for Supply Temperature Sensor

High / Low Temp Sensor Temp. (oF) Resistance (Ohms)

32 32550

41 25340

50 19870

59 15700

68 12490

77 10000

86 8059

95 6535

104 5330

113 4372

122 3605

131 2989

140 2490

149 2084

158 1753

167 1481

176 1256

185 1070

194 915

202 786

212 667

Table 15 - Supply Temperature Resistance Sensor

The water heater must be full of water and the system fully purged BEFORE powering the water heater. Performing any work in the plumbing system without either powering o the water heater or isolating the water heater through the use of shut-o valves could result in a condition referred to as “dry-ring”. Dry-ring the water heater will damage the heat exchanger, and could result in property damage, serious personal injury, or death. Such damages ARE NOT covered by water heater warranty.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 35

Part 11 - Troubleshooting

A. Error Code

An error code may occur during installation of the heater. This condition may lead to a lock out condition of the controller, which will need to be manually reset by pressing S4. The following information will help the installer correct the problem before going into a lockout condition, which will require a manual reset.

B. Heater Error

1. When an error condition occurs the controller will display an error code on the display module.

2. These error codes and several suggested corrective actions are included in Table 16.

3. In the case of E00, E13, and E14 error codes, if uncorrected, the water heater will go into a fault condition as described in section C. Lockout.

C. Lockout

1. When an fault condition occurs, the controller will illuminate the red fault indication light and display a fault code (example: F00).

2. Note the fault code and refer to Table 17 for an explanation of the fault code along with several suggestions for corrective actions.

3. Press S4 to clear the fault and resume operation. Be sure to observe the operation of the unit to prevent a recurrence of the fault.

When servicing or replacing any components of this water heater be certain that:

• The gas is o.

• All electrical power is disconnected. In addition, when servicing or replacing components of this water heater in direct contact with heater water:

• There is no pressure in the heater. Pull the release on the relief

valve to relieve pressure in the heater.

• Heater water is not hot. Failure to follow these precautions could result in property damage, serious personal injury, or death. Such damages ARE NOT covered by water heater warranty.

DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN SUBMERGED IN WATER. Immediately call a qualied service technician. The

appliance MUST BE replaced if it has been submerged. Attempting to operate an appliance that has been submerged could create numerous harmful conditions, such as a potential gas leakage causing a re and/or explosion, or the release of mold, bacteria, or other harmful particulates into the air. Operating a previously submerged appliance could result in property damage, severe personal injury, or death. NOTE: Appliance damage due to ood or submersion is considered an Act of God, and IS NOT covered under product warranty.

The water heater has wire function labels on all internal wiring. Observe the position of each wire before removing it. Wiring errors may cause improper and dangerous operation. Verify proper operation after servicing.

926 Control Board Error Codes

Code Description Duration Corrective Action

E13

E14

LEO Water level in tank is low

FLU

LOU 24 Volt low

Table 16 - Error Codes

Combustion blower speed is less

than 70% of expected

Combustion blower speed is greater

than 130% of expected

Blocked Vent, Pressure Switch open,

Condensate Cup full, Condensate

Cup not present

60 seconds

Until corrected

1. Check blower wiring. Ensure all wires are plugged in and undamaged.

2. Replace the blower.

3. Replace the control board.

1. Check blower wiring. Ensure all wires are plugged in and undamaged.

2. Replace the blower.

3. Replace the control board.

1. Ensure all air is bled from system.

2. Inspect low level switch and wiring for damage and repair if necessary.

1. Check the ue vent to be sure it is not blocked or damaged.

2. Check blocked vent pressure switch operation by applying a jumper. If the switch is not functioning properly, replace it.

1. Check line voltage. Must be between 100 - 128 volts.

2. If available, connect a PC and, using HTP service software, check the 24V supply display in the lower left corner of the screen. The number displayed must be greater than 128 and should be greater than 250. Use this as a troubleshooting guide as you follow the steps below.

3. Remove 10 pin Molex connector from customer connection board. If the LOU code clears, the problem is with external sensor wiring. Examine external sensor wiring for shorts to ground, repairing as necessary. If LOU code is still present and the heater is so equipped, disconnect high gas pressure switch, then low gas pressure switch, then UL 353 low water cuto in this order, one at a time, to see if LOU code clears. Replace faulty part. Check low voltage wire harness in heater for shorts to ground.

4. If LOU only occurs when burner tries to light, check gas valve for excessive current draw.

5. If LOU is present with the low voltage harness disconnected from the 926 control board, replace the 926 control board.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 36

926 Control Board Fault Codes

Code Description Corrective Action

1. Try to reset the water heater. If F00 repeats, create a demand for hot water. (WARNING: Use caution to prevent burn injury.) If water is above 194oF, test upper and lower temperature sensors with an ohmmeter. (Refer to resistance chart, this section.) Replace bad sensor.

F00

High temperature switch limit

exceeded 194oF

F01 Vent temperature limit exceeded

F02

F03

Interrupted or shorted upper

temperature sensor

Interrupted or shorted lower

temperature sensor

F05 Upper temp. sensor exceeds 194oF 1. If water in tank is less than 194oF, check wiring. Repair if damaged.

F06 Lower temp. sensor exceeds 194oF

No ame detected - Heater will make

F09

three attempts at ignition before the control goes into this lockout

condition. Will reset in 1 hour.

Loss of ame signal - The heater will

F10

attempt to relight four times before the control goes into this condition.

Will reset in 1 hour.

False ame signal - Occurs if heater

F11

senses a ame signal when there

should be none present.

Blower speed incorrect - Occurs

F13

if blower speed is less than 70%

expected for more than 60 seconds.

Table 17 - Fault Codes - NOTE: If you replace a part to remedy a fault, it is recommended that you cycle the water heater at least three or four times to assure the fault has been resolved.

If water is below 194oF, test high temperature switch and wiring with ohmmeter. Switch should be closed at this point. If not, replace switch.

2. If heater did reset successfully, let the heater run and go into the status menu to check the upper and lower temperature sensors. If either reading displayed does not make sense, check appropriate sensor with ohmmeter. (Refer to resistance chart, Table 15.) Replace bad sensor. Do an OHMs reading on both sensors to check continuity.

1. Inspect all ue piping. If the ue is damaged or shows signs of overheating, repair or replace the ue parts as necessary before proceeding.

2. If the ue piping is intact, undamaged, and there is no sign of the ue overheating (such as discoloration or melting of the ue pipe), push the red reset button on the ue switch.

3. Be sure the heater is connected to a water supply and is full of water.

4. Push the RESET button on the heater control panel. The water heater should light. If the water heater lights, proceed to step 5. If the water heater does not light and the display again begins to ash F01, inspect the wiring to the ue switch, repairing or replacing as necessary. If the wiring is intact, replace the ue switch, using care to mount the new ue switch in the same position and mounting holes as the old one. If the display ashes a code other than F01, follow the troubleshooting guide for the code.

5. Observe operation for 5 minutes. Place the probe of an exhaust analyzer into the ue system within 6 feet of the heater. The exhaust temperature should not rise above 190oF after several minutes of operation.

6. If the ue temperature is below 190oF and the heater again goes into lockout displaying F01, replace the ue switch, using care to mount the new ue switch in the same position and mounting holes as the old one. If the display ashes a code other than F01, follow the troubleshooting guide for that code.

7. If the ue temperature increases to over 190oF, consult HTP for further assistance.

1. Check the electrical connection to the appropriate temperature sensor.

2. If connection is intact, replace the sensor.

2. If wiring is intact, check appropriate sensor with ohmmeter and compare to reading in Table 15. If reading does not agree with water temperature, replace the sensor.

1. Watch the igniter through the observation window provided.

2. If there is no spark, check the spark electrode for the proper 1/4” gap.

3. Remove any corrosion from the spark electrode and ame rectier probe.

4. If there is a spark but no ame, check the gas supply to the heater.

5. If there is a ame, check the ame sensor.

6. Check for any ue or condensate blockages.

1. Monitor the gas pressure to the unit while in operation.

2. Assure that the ame is stable when lit.

3. Check to see if the green light on the display module is out while the heater is running.

4. If the green light doesn’t come on or goes o during operation check the ame signal on the status menu.

5. If the signal reads less than 1 microampere, clean the ame rectier probe.

6. If the ame rectier probe continues to read low, replace it.

1. Turn the gas o to the unit as the service valve.

2. If the ame signal is still present replace the igniter.

3. If the ame signal is not present after turning o the gas supply, check the gas valve electrical connection.

4. If there is no power to the gas valve, remove the valve and check for obstruction in the valve seat or replace the gas valve.

5. Turn the gas on at the service valve after corrective action is taken.

1. Check blower wiring.

2. Replace the blower.

3. Replace the control board.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 37

Part 12 - Installation Checklist

Before Installing Yes No

Is there enough space to ensure proper installation?

Does installation location allow for proper service clearances?

Are water and gas lines properly sized and set at proper pressures for the installation?

Is water heater location as near the exhaust vent / intake pipe terminations as possible?

Have combustible materials been cleared from the installation location?

Is there a drain close to the water heater?

Water Piping Yes No

Does water heater loop piping meet the minimum sizing requirements listed? NOTE: Smaller piping will cause performance problems.

Has water chemistry been checked?

Does water chemistry meet requirements?

If water chemistry does not meet requirements, have treatment measures been put in place?

Has the system been cleaned and ushed?

Install Exhaust Vent and Intake Piping Yes No

Has the water heater been vented with the approved materials listed in this manual or to meet local codes?

Is air supply sucient for proper water heater operation?

Is total vent piping length within the maximum vent length restriction listed in this manual?

Have venting lengths been minimized?

Are terminations properly spaced from windows, doors, and other intake vents?

Have all vent terminations been installed at least one foot above exterior grade and one foot above normal snow accumulation level?

Is vent piping properly supported?

Has vent piping been checked for leaks?

Has the exhaust vent line been pitched back to the water heater at a rate of 1/4” per foot?

Have the exhaust vent and intake pipes been properly installed to the water heater?

Install Condensate Piping / Tubing and Components Yes No

Have all condensate components included with the water heater been installed?

Is the condensate line piped with approved materials listed in this manual?

Has the condensate line been routed to a laundry tub or other drain?

Install Gas Piping Yes No

Is the gas supply line a minimum of 3/4” in diameter?

Is the gas supply line length and diameter adequate to deliver the required BTUs?

Has gas supply line pressure been measured?

Does the gas type match the type indicated on the water heater rating plate?

Has a union and shut-o valve been installed?

Relief Valve Yes No

Is the Temperature and Pressure Relief Valve properly installed and discharge line run to open drain?

Is the discharge line protected from freezing?

Wiring Yes No

Has the power and control been wired per water heater wiring diagram, this manual?

Is the electrical connection polarity within water heater requirements?

Does the power supply voltage agree with the water heater rating plate?

Is the branch circuit wire and fusing or circuit breaker of proper size?

Are electrical connections tight and properly grounded?

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 38

Start-Up, Adjust, and Test Yes No

Has the water heater been started?

If necessary, has the water heater gas valve been adjusted?

Has the installation been customized per installation location requirements?

Have all customized system parameters been tested?

Has proper water heater operation been conrmed?

Final Installation Approvals

Signed by Technician Date

Table 18 - Installation Checklist

Part 13 - Maintenance

Periodic maintenance should be performed once a year by a qualied service technician to assure that all the equipment is

In unusually dirty or dusty conditions, care must be taken to keep water heater cabinet door in place at all times. Failure to do so VOIDS the warranty.

Allowing the water heater to operate with a dirty combustion chamber will hurt operation. Failure to clean the heat exchanger as needed by the installation location could result in water heater failure, property damage, personal injury, or death. Such product failures ARE NOT covered under warranty.

Hydrogen gas can build up in a hot water system served by this water heater that has not been used for a long period of time (generally two weeks or more). When opening a hot water faucet in a system that has been out of use for a time, keep all ignition sources (electrical appliances, open ame, etc.) away from the faucet. If hydrogen is present, there will be a sound of air escaping as water begins to ow. Allow the water to run for a few minutes to dissipate built up hydrogen from the system. Failure to follow these instructions can result in property damage, personal injury, or death.

The water heater requires minimal periodic maintenance under normal conditions. However, in unusually dirty or dusty conditions, periodic vacuuming of the cover to maintain visibility of the display and indicators is recommended.

operating safely and eciently. The owner should make necessary arrangements with a qualied heating contractor for periodic maintenance of the heater. Installer must also inform the owner that the lack of proper care and maintenance of the heater may result in a hazardous condition.

It is extremely important that whenever work is performed on the plumbing system that either:

• The water heater is powered o, or,

• The water heater is valved o and isolated from the

plumbing system.

Failure to take these measures could result in a dry-ring condition.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 39

Inspection Activities Date Last Completed

Piping 1st Year 2nd Year 3rd Year 4th Year*

Near heater piping

Vent

Gas

System 1st Year 2nd Year 3rd Year 4th Year*

Visual Do a full visual inspection of all system components.

Functional Test all functions of the system (Heat, Safeties).

Temperatures

Electrical

Connections Check wire connections. Make sure connections are tight.

Smoke and CO Detector

Circuit Breakers Check to see that the circuit breaker is clearly labeled. Exercise circuit

Chamber / Burner 1st Year 2nd Year 3rd Year 4th Year*

Combustion Chamber

Spark Electrode Clean. Set gap at 1/4” Clean probe with plumbers cloth to remove

Combination Ignitor and Flame Probe

Condensate 1st Year 2nd Year 3rd Year 4th Year*

Neutralizer Check condensate neutralizer. Replace if necessary.

Condensate Pipe Disconnect condensate pipe. Clean out dirt. Fill with water to level

Gas 1st Year 2nd Year 3rd Year 4th Year*

Pressure Measure incoming gas pressure (3.5” to 10” WC for Natural Gas, 8” to

Pressure Drop Measure drop in pressure on light o (no more than 1” WC).

Check Gas Pipe for Leaks

Combustion 1st Year 2nd Year 3rd Year 4th Year*

CO / CO2 Levels Check CO and CO2 levels in exhaust. See Start-Up Procedures for

Safeties 1st Year 2nd Year 3rd Year 4th Year*

ECO (Energy Cut Out)

Sensors Check wiring. Verify through ohms reading.

Final Inspection 1st Year 2nd Year 3rd Year 4th Year*

Check List Verify that you have completed entire check list. WARNING: FAILURE

Homeowner Review what you have done with the homeowner.

Table 19 - *Continue annual maintenance beyond the 4th year as required.

Check heater and system piping for any sign of leakage; make sure pipes are properly supported.

Check condition of all vent pipes and joints. Ensure the vent piping terminations are free of obstructions and blockages.

Check gas piping. Test for leaks and signs of aging. Make sure all pipes are properly supported.

Verify safe settings on heater or anti-scald valve.

Verify programmed temperature settings.

Verify devices are installed and working properly. Change batteries if necessary.

breaker.

Check burner tube and combustion chamber coils. Clean according to maintenance section of manual. Vacuum combustion chamber. Replace any gaskets that show signs of damage.

oxides.

Check ionization in uA (d7 in Status Menu in Start-Up Procedures). Record high re and low re. Clean probe with plumbers cloth to remove oxides.

of outlet and reinstall. (NOTE: Verify the ow of condensate, making sure that the hose is properly connected during nal inspection.)

14” WC for Propane).

Check piping for leaks. Verify that all are properly supported.

ranges. Record at high and low re.

Check continuity on ue and water ECO. Replace if corroded.

TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 40

Part 14 - Replacement Parts

5 6

Figure 26 - Outdoor Cabinet Replacement Parts

PHP260, 320, 399

ITEM#

(PHP199D)

1 7100P-371 7100P-41 1 CABINET-TOP PANEL

2 7100P-369 7100P-40 7 CABINET-RIGHT SIDE PANEL

3 7100P-368 7100P-40 8 CABINET-LEFT SIDE PANEL

4 7100P-370 7100P-40 9 CABINET-BACK PANEL

5 7100P-383 CABINET-COVER PLATE-OUTLET

6 7100P-385 GROMMET-LIP STYLE

7 7500P-115 SCREWS-COVER PLATE, CONTROL BOARD PLATE

8 7100P-374 7100P-41 0 CABINET-FRONT PANEL

9 7100P-381 7100P-41 2 PLATE-CONTROL BOARD

10 7450P-122 CONTROL BOARD

11 7100P-157 7100P-413 WIRE HARNESS LOW VOLTAGE - STAGE 1

12 7100P-158 WIRE HARNESS 12 0V - STAGE 1

13 7100P-151 N/A WIRE HARNESS - LOW VOLTAG E - STAGE 2

14 7100P-153 N/A WIRE HARNESS - 120V - STAG E 2

15 7250P-150 PRESSURE SWITCH

16 7100P-382 CABINET-COVER PLA TE-INLET (NOT SHOWN)

17 7100P-384 CABINET-COVER PLA TE-AUXILIARY (NOT SHOWN)

18 7700P-097 TERMINAL BLOCK

19 7100P-009 DISPLAY ASSEMBLY

20 7350P-157 SCREWS - CABINET CO VER PLATE

NOITPIRCSED991PHP

LP-454-W

LP-454-W 04/07/17

04/07/17

Figure 27 - Tank Assembly Replacement Parts

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 41

LP454-X

04/03/17

Item

1 GASKET - MOUNTING PLATE 7100P-139

2 MOUNTING PLATE 7100P-007

3 GASKET - PROBES 7100P-155

4 FLAME RECTIFICATION PROBE 7100P-082

5 IGNITOR ELECTRODE 7100P-124

6 10-32 X 3/8 SCREWS/#10 LOCK WASHERS N/A

7 SCREWS - 5/16-18 7700P-101

8 GASKET - BURNER MOUNTING FLANGE 7100P-152

9 BURNER - 100-130K BTU 7100P-516

BURNER - 160-199K BTU 7100P-517

10 GASKET - BURNER OUTLET 7000P-361

11 GASKET - SIGHT GLASS 7100P-105

12 SIGHT GLASS G2000

13 AIR CHANNEL 7100P-048

14 1/4-20 BRASS NUTS/1/4 LOCK WASHERS 7100P-268

15 GASKET - BLOWER TO AIR CHANNEL 7500P-075

Description

Replacement Part

Item

16 COMBUSTION BLOWER (w/GASKET, SIGHT GLASS) 7100P-518

17 SCREWS - 10-32 x 1/2 7700P-094

18 ADAPTER PLATE 7250P-644

19 FLAT HEAD SCREW - ADAPTER PLATE 7100P-045

20 AIR INTAKE ADAPTER - BLOWER SIDE 7500P-185

21 SWIRL PLATE - BLACK (100/130K BTU) 7100P-042

SWIRL PLATE - WHITE (160/199K BTU) 7500P-092

22 AIR INTAKE ADAPTER - VALVE SIDE 7500P-184

23 GAS VALVE (100/130K BTU) 7000P-862

GAS VALVE (160/199K BTU) 7000P-863

24 GAS VALVE ADAPTER (w/O-RING) 7250P-454

25 SCREWS - M4 X 20MM - GAS VALVE ADAPTER 7250P-717

26 GAS SHUT-OFF VALVE 7250P-140

27 1/2" FLARE X 1/2" NPT FLEX HOSE 7100P-140

28 TUBE - AIR INLET 7500P-189

Description

Replacement Part

Figure 28 - Replacement Parts - Combustion System

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 42

Phoenix® Plus Gas Water Heater

Limited Warranty

For Commercial Use

HTP warrants this water heater and its components to be free from defects in material and workmanship according to the following terms, conditions, and time periods. UNLESS OTHERWISE NOTED THESE WARRANTIES COMMENCE ON THE DATE OF INSTALLATION. This limited warranty is only available to the original consumer purchaser (herinafter “Owner”) of this water heater, and is nontransferable.

Commercial Use Warranty (3 years – Tank, 1 year – Parts)

COVERAGE

A. During the rst year after the original date of installation, HTP warrants that it will repair or replace, at its option, any defective or malfunctioning component of the water heater with a component of equivalent size and current model. Replacement components will be warranted for ninety (90) days. B. Should a defect or malfunction result in a leakage of water from the water heater within the above-stated warranty periods due to defective material or workmanship, malfunction, or failure to comply with the above warranty, with such defect or malfunction having been veried by an authorized HTP representative, HTP will replace the defective or malfunctioning water heater with a replacement of the nearest comparable model available at the time of replacement. The replacement water heater will be warranted for the unexpired portion of the applicable warranty period of the original water heater. C. In the event of a leakage of water of a replacement water heater due to defective material or workmanship, malfunction, or failure to comply with the above warranty, HTP reserves the right to refund to the Owner the published wholesale price available at the date of manufacture of the original water heater. D. If government regulations, industry certication, or similar standards require the replacement water heater or component(s) to have features not found in the defective water heater or component(s), the Owner will be charged the dierence in price represented by those required features. If the Owner pays the price dierence for those required features and/or to upgrade the size and/or other features available on a new replacement water heater or component(s), the Owner will also receive a complete new limited warranty for that replacement water heater or component(s). E. If at the time of a request for service the Owner cannot provide a copy of the original sales receipt or the warranty registration, the warranty period for the water heater shall then be deemed to have commenced thirty (30) days after the date of manufacture of the water heater and NOT the date of installation of the water heater. F. This warranty extends only to water heaters utilized in heating applications that have been properly installed by qualied professionals based upon the manufacturer’s installation instructions. G. It is expressly agreed between HTP and the Owner that repair, replacement, or refund are the exclusive remedies of the Owner.

OWNER RESPONSIBILITIES

The Owner or Qualied Installer / Service Technician must:

1. Have a relief valve bearing the listing marks of the American Society of Mechanical Engineers (ASME) installed with the water heater assembly in accordance with federal, state, and local codes.

2. Have a vacuum relief valve certied to ANSI Z21.22 - Relief Valves for Hot Water Supply Systems installed with the water heater assembly in accordance with federal, state, and local codes and in installations prone to vacuum related damages.

3. Maintain the water heater in accordance with the maintenance procedure listed in the manufacturer’s provided instructions. Preventive maintenance can help avoid any unnecessary breakdown of the water heater and keep it running at optimum eciency.

4. Maintain all related system components in good operating condition.

5. Use the water heater in an open system, or in a closed system with a properly sized and installed thermal expansion tank.

6. Use the water heater at water pressures not exceeding the working pressure shown on the rating plate.

7. Keep the water heater free of damaging scale deposits.

8. Make provisions so if the water heater or any component or connection thereto should leak, the resulting ow of water will not cause damage to the area in which it is installed.

WARRANTY EXCLUSIONS

This limited warranty will not cover:

1. Any water heater purchased from an unauthorized dealer.

2. Any water heater not installed by a qualied installer / service technician, or installations that do not conform to ANSI, CSA, and/ or UL standards, as well as any applicable national or local building codes.

3. Service trips to teach the Owner how to install, use, maintain, or to bring the water heater installation into compliance with local building codes and regulations.

4. Failure to locate the water heater in an area where leakage of the water heater or water line connections and the relief valve will not result in damage to the area adjacent to the water heater or lower oors of the structure.

5. Any failed components of the system not manufactured by HTP as part of the water heater.

6. Water heaters repaired or altered without the prior written approval of HTP.

7. Damages, malfunctions, or failures resulting from failure to install the water heater in accordance with applicable building codes/ ordinances or good plumbing and electrical trade practices.

8. Damages, malfunctions, or failures resulting from improper installation, failure to operate the water heater at ring rates or pressures not exceeding those on the rating plate, or failure to operate and maintain the water heater in accordance with the manufacturer’s provided instructions.

9. Failure to operate the water heater in a an open system, or in a closed system with a properly sized and installed thermal expansion tank.

10. Failure or performance problems caused by improper sizing of the water heater, expansion device, piping, or the gas supply line, the venting connection, combustion air openings, electric service voltage, wiring or fusing.

11. Damages, malfunctions, or failures caused by improper conversion from natural gas to LP gas or LP gas to natural gas.

12. Damages, malfunctions, or failures caused by operating the water heater with modied, altered, or unapproved components, or any component / attachment not supplied by HTP.

13. Damages, malfunctions, or failures caused by abuse, accident, re, ood, freeze, lightning, acts of God and the like.

14. Failures (leaks) caused by operating the water heater in a corrosive or contaminated atmosphere.

15. Damages, malfunctions, or failures caused by operating an empty or partially empty water heater (“dry ring”), or failures caused by operating the water heater when it is not supplied with water, free to circulate at all times.

16. Any damage or failure of the water heater due to the accumulation of solid materials or lime deposits.

17. Any damage or failure resulting from improper water chemistry. WATER CHEMISTRY REQUIREMENTS (COMMERCIAL USE) - Water pH between 6.5 and 8.5. Hardness less than 7 grains (120 mg/L). Chloride concentration less than 100 ppm (mg/L). TDS less than 500 ppm (mg/L).

18. Any damages, malfunctions, or failures resulting from the use of dielectric unions.

19. Water heaters replaced for cosmetic reasons.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 43

20. Components of the water heater that are not defective, but must be replaced during the warranty period as a result of reasonable wear and tear.

21. Components of the water heater that are subject to warranties, if any, given by their manufacturers; HTP does not adopt these warranties.

22. Damages, malfunctions, or failures resulting from the use of any attachment(s) not supplied by HTP.

23. Water heaters installed outside the fty states (and the District of Columbia) of the United States of America and Canada.

24. Water heaters moved from the original installation location.

25. Water heaters that have had their rating labels removed.

PROCEDURES FOR WARRANTY SERVICE REQUESTS

Any claim for warranty assistance must be made promptly. Determine if the water heater is “in-warranty” (that is, within the applicable warranty period) by reviewing a copy of the original sales receipt or warranty registration. The Owner must present a copy of the original sales receipt or warranty registration for a warranty service request. If the water heater is “in-warranty”, contact the retailer from whom the water heater was purchased (or the installer) for assistance. Be prepared to provide the retailer or installer with a copy of the original receipt, complete model and serial numbers, and the date of installation of the water heater, in addition to an explanation of the water heater problem. Warranty coverage is subject to validation of “in-warranty” coverage by HTP claims department personnel. All alleged defective or malfunctioning components must be returned to HTP via the local distribution channels where the original purchase was made.

NOTE: Any components or water heaters returned to HTP for warranty analysis will become the property of HTP and will not be returned, even if credit is denied.

If all warranty conditions are satised, HTP will provide replacement components to the retailer. For questions about the coverage of this warranty, please contact HTP at the following address or phone number: HTP Comfort Solutions LLC, 272 Duchaine Blvd., New Bedford, MA, 02745, Attention: Warranty Service Department, 1(800) 323-9651.

AND SIGNED BY A DULY AUTHORIZED OFFICER OF HTP. THE WARRANTIES STATED HEREIN ARE NOT TRANSFERABLE AND SHALL BE FOR THE BENEFIT OF THE ORIGINAL OWNER ONLY.

NO OTHER WARRANTIES

This warranty gives the Owner specic legal rights. The Owner may also have other rights that vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to the Owner. These are the only written warranties applicable to this water heater manufactured and sold by HTP. HTP neither assumes nor authorizes anyone to assume for it any other obligation or liability in connection with said water heaters. HTP reserves the right to change specications or discontinue models without notice.

SERVICE, LABOR AND SHIPPING COSTS

This limited warranty does not extend to any shipping charges, delivery expenses, or administrative fees incurred by the Owner in repairing or replacing the water heater or component(s). This warranty does not extend to labor costs beyond the coverage specied in this warranty document. All such expenses are the Owner’s responsibility.

LIMITATIONS OF YOUR HTP WARRANTY AND REMEDIES THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE GIVEN AND ACCEPTED TO THE FURTHEST EXTENT UNDER APPLICABLE LAW IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER OR NOT ARISING FROM HTP’S NEGLIGENCE, ACTUAL OR IMPUTED. THE REMEDIES OF THE OWNER SHALL BE LIMITED TO THOSE PROVIDED HEREIN TO THE EXCLUSION OF ANY OTHER REMEDIES INCLUDING WITHOUT LIMITATION, INCIDENTAL OR CONSEQUENTIAL DAMAGES, SAID INCIDENTAL AND CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROPERTY DAMAGE, LOST PROFIT OR DAMAGES ALLEGED TO HAVE BEEN CAUSED BY ANY FAILURE OF HTP TO MEET ANY OBLIGATION UNDER THIS AGREEMENT INCLUDING THE OBLIGATION TO REPAIR AND REPLACE SET FORTH ABOVE. NO AGREEMENT VARYING OR EXTENDING THE FOREGOING WARRANTIES, REMEDIES OR THIS LIMITATION WILL BE BINDING UPON HTP. UNLESS IN WRITING

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 44

Maintenance Notes

LP-454 Rev. 004 Rel. 002 Date 12.1.17

Page 45

Customer Installation Record Form

The following form should be completed by the qualied installer / service technician for you to keep as a record of the installation in case of a warranty claim. After reading the important notes at the bottom of the page, please also sign this document.

Customer’s Name

Date of Installation

Installation Address

Product Name / Serial Number(s)

Comments

Installer’s Code / Name

Installers Phone Number

Signed by Installer

Signed by Customer

Installation Notes

IMPORTANT

Customer: Please only sign after the qualied installer / service technician has fully reviewed the installation, safety, proper operation, and maintenance of the system. If the system has any problems please call the qualied installer / service technician. If you are unable to make contact, please call your sales representative. Distributor / Dealer: Please insert contact details.

LP-454 Rev. 004 Rel. 002 Date 12.1.17

HTP PHP260-119, PHP199-119, PHP320-119, PHP399-119 Installation, Setup, Maintenance

Specifications and Main Features

Frequently Asked Questions

User Manual