HTP CGH-199O Installation, Start-up, Maintenance, Parts And Warranty

Download

Page 1

Installation

Start-Up

Maintenance

Parts

Warranty

CGH-199O* Models

Crossover

Outdoor Water Heaters

*O Denotes Outdoor Models; “LP” Denotes Propane Gas; “F” Denotes Floor Models with Built-In Pump

The outdoor unit is intended for use in outdoor installations ONLY. DO NOT install the water heater indoors. Installing the water heater indoors will result in improper water heater operation, property damage, serious personal injury, or death.

This manual must only be used by a qualied installer / service technician. Read all instructions in this manual before installing. Perform steps in the given order. Failure to do so could result in substantial property damage, severe personal injury, or death.

Improper installation, adjustment, alteration, service, or maintenance could void product warranty and cause property damage, severe personal injury, or death.

California Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The manufacturer reserves the right to make product changes or updates without notice and will not be held liable for typographical errors in literature.

The surfaces of these products contacted by potable (consumable) water contain less than 0.25% lead by weight as required by the Safe Drinking Water Act, Section 1417.

NOTE TO CONSUMER: PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.

272 Duchaine Blvd. New Bedford, MA 02745 www.htproducts.com

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 2

WARNING: If the information in these instructions is not followed exactly, a re or explosion may result causing property damage, personal injury or death.

• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

• Installation and service must be provided by a qualied installer, service agency or the gas supplier.

Improper installation, adjustment, alteration, service, or maintenance can cause injury, property damage, or death. Refer to this manual. Installation and service must be performed by a qualied installer, service agency, or gas supplier.

The following dened terms are used throughout this manual to bring attention to the presence of hazards of various risk levels or to important product information.

DANGER indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury or death.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in personal injury or death.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor personal injury.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

NOTICE is used to address practices not related to personal injury.

Page 3

Foreword

This manual is intended to be used in conjunction with other literature provided with the water heater. This includes all related control information. It is important that this manual, all other documents included in this system, and additional publications including the National Fuel Gas Code - ANSI Z223.1 (latest versions), be reviewed in their entirety before beginning any work.

Installation should be made in accordance with the regulations of the Authority Having Jurisdiction, local code authorities, and utility companies which pertain to this type of water heating equipment.

Authority Having Jurisdiction (AHJ) – The AHJ may be a federal, state, local government, or individual such as a re chief, re marshal, chief of a re prevention bureau, labor department or health department, building ocial or electrical inspector, or others having statutory authority. In some circumstances, the property owner or his/ her agent assumes the role, and at government installations, the commanding ocer or departmental ocial may be the AHJ.

NOTE: The manufacturer reserves the right to modify product technical specications and components without prior notice.

For the Installer

This water heater must be installed by qualied and licensed personnel. The installer should be guided by the instructions furnished with the water heater, and by local codes and utility company requirements. In the absence of local codes, preference should be given to the National Fuel Gas Code - ANSI Z223.1, latest version.

Installations Must Comply With:

Local, state, provincial, and national codes, laws, regulations, and ordinances.

The latest version of the National Fuel Gas Code, ANSI Z223.1, from American Gas Association Laboratories, 8501 East Pleasant Valley Road, Cleveland, OH 44131.

In Canada - CGA No. B149 (latest version), from Canadian Gas Association Laboratories, 55 Scarsdale Road, Don Mills, Ontario, Canada M3B 2R3. Also, Canadian Electrical Code, C 22.1, from Canadian Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6.

The latest version of the National Electrical Code, NFPA No. 70.

In the State of California: The water heater must be braced, anchored, or strapped to avoid moving during an earthquake. Contact local utilities for code requirements in your area or call 1-866-000-0000 and request instructions. In the Commonwealth of Massachusetts:

a. Outdoor units may be used for summer use only. b. The water heater may be used for hot water heating only and may

not be used in a combination of domestic and space heating. NOTE: The gas manifold and controls met safe lighting and other performance criteria when undergoing tests specied in ANSI Z21.10.3

- latest edition.

From the Uniform Plumbing Code 2000 - Section 510 -

Protection From Damage

1. All water heaters installed in areas where they may be subjected to mechanical damage shall be suitably guarded against such damage by being installed behind adequate barriers or by being elevated or located out of the normal path of a vehicle using any such garage.

2. In seismic zones 3 and 4, water heaters shall be anchored or strapped to resist horizontal displacement due to earthquake motion. Strapping shall be at points within the upper one-third (1/3) and lower one-third (1/3) of its vertical dimensions. At the lower point, a minimum distance of four (4) inches (102 mm) shall be maintained above the controls with the strapping.

3. An water heater supported from the ground shall rest on level concrete or other approved base extending not less than three (3) inches (76 mm) above the adjoining ground level.

4. When a water heater is located where damage may result from a leaking water heater, a watertight pan of corrosion resistant materials shall be installed beneath the water heater with a minimum threequarter (3/4) inch (20 mm) diameter drain to an approved location.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 4

Table of Contents

Part 1 - General Safety Information 4

A. Operation and Installation Warnings 4 B. Improper Combustion 6 C. Gas 6 D. When Servicing the Water Heating System 6 E. Water Chemistry Requirements 6 F. Freeze Protection 6 G. Water Temperature Adjustment and Scalding 7 H. High Elevation Installations 7

Part 2 - Before You Start 8

A. What’s in the Box 8 B. Optional Equipment 8

Part 3 - Prepare the Water Heater Installation 8

A.Choosing an Outdoor Installation Location 8 B. Leveling 9 C. Clearances for Service Access 9 D. Exhaust Vent and Air Intake 10 E. Carbon Monoxide Detectors 11 F. Prevent Combustion Air Contamination 11 G. Technical Specications 12 H. Wall-Mounting 15

Part 4 - Water Piping 16

A. General Plumbing Guidelines 16 B. Backow Preventer 17 C. Potable Expansion Tank 17 D. Piping the Water Heater 17 E. Applications 17 F. Circulator Sizing 24 G. Pressure Relief Valve 25 H. Filling the Heater 26

Part 5 - Venting 26

A. General 26 B. Exhaust Vent and Air Intake Location 27 C. Water Heater Exhaust Vent and Air Intake Notes 28 D. Application 28

Outdoor Installation 29

Part 6 - Installing the Condensate Drain 30 Part 7 - Connecting Electrical Service 31

A. Field Wiring Terminations 31 B. Line Voltage Wiring 31 B. Dip Switches 31 C. Wiring a Cascaded System 32

Part 8 - Gas Connections 37

A. Gas Pipe Sizing Tables 37

1. Gas Pipe Sizing 37

2. Natural Gas Pipe Sizing 37

3. LP (Liquid Propane) Gas Pipe Sizing 37

B. Gas Connection Requirements 37 C. Additional Precaution for Excess Flow Valve (EFV) 38 D. Checking Gas Pressure at the Water Heater for Proper Operation

E. Setting and Verifying the Combustion Setting 38

Part 9 - Controls 39

A. Control and Display Overviews 39 B. Start-Up Sequence 39 C. Changing the DHW Set-Point 40 D. Changing the Time 40 E. Lock Function 40 F. Status Display 41 G. Installer Mode 42 H. Setting Up a Cascaded System 43 I. Using Recirculation Modes - Step 1 44 J. Recirculation Functions - Using Recirculation Modes - Step 2 45

1. Smart Auto-Learn Recirculation Function 46

2. Pro1, Pro2, Pro3, and PULS Recirculation Function 46

Part 10 - Troubleshooting 47

A. Error Code 47 B. Error Tree Analysis 51

1. Flame Detection 51

2. Air Pressure Switch Detection 51

3. Recirculation / Inlet / DHW / Operating Temperature / Exhaust Sensors 52

C. Suggested Corrective Actions 52

Part 11 - Installation Checklist 54 Part 12 - Maintenance 56 Part 13 - Replacement Parts 59

Limited Warranty for RGH Water Heaters 65 Notes 67 Customer Installation Record Form 68

Part 1 - General Safety Information

This water heater is approved for outdoor installations and is not intended for use as a pool heater. Clearance to combustible materials: 0” top, bottom, sides, and back. Heater must have room for service: 24” front and 12” sides are minimum recommended service clearances. Special attention should be paid to ensure that T&P valve discharge and drainage from condensate line will not adversely aect the surrounding area or pose a hazard in freezing conditions.

This water heater has a condensate disposal system that may freeze if exposed to sustained temperatures below 32oF. Precautions should be taken to protect the condensate trap and drain lines from freezing conditions. Failure to take precautions could result in property damage, serious personal injury, or death.

Installer - Read all instructions in this manual before installing. Perform steps in the given order.

User - This manual is for use only by a qualied heating installer / service technician. Have this water heater serviced / inspected annually by a qualied service technician.

FAILURE TO ADHERE TO THE GUIDELINES ON THIS PAGE CAN RESULT IN SUBSTANTIAL PROPERTY DAMAGE, SEVERE PERSONAL INJURY, OR DEATH.

NOTE: Obey all local codes. Obtain all applicable permits before

installing the water heater.

NOTE: Install all system components and piping in such a manner that does not reduce the performance of any re rated assembly.

A. Operation and Installation Warnings

To avoid serious injury or death, read, understand, and follow all of the precautions listed here.

Vapors from ammable liquids will explode and can cause a re, resulting in personal injury or death. The water heater has a burner that can come on at any time and ignite vapors. DO NOT use or store ammable liquids around the water heater.

Improper venting can cause a build-up of carbon monoxide. Breathing carbon monoxide can result in brain damage or death. DO NOT operate the water heater unless it is properly vented and has an adequate fresh air supply for safe operation. Inspect the exhaust gas outlet port and fresh air inlet ports on a regular basis to ensure they are functioning properly.

A concentration of carbon monoxide as small as .04% (400 parts per million) in the air can be fatal. When making high re or low re adjustments, CO levels must be monitored using a ue gas analyzer such that a CO level of no more than 150 ppm is exceeded at any time during operation.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 5

Adjusting the “low re oset” or the “main ow restrictor” in small increments can result in a signicant increase in CO concentration. To avoid serious injury or death, DO NOT make any adjustments to the gas valve without monitoring the exhaust gases with a fully functional and calibrated ue gas analyzer.

This water heater must be installed by a licensed plumber, licensed gas tter, and/or professional service technician. Improper installation and/or operation can cause a potentially hazardous situation, which, if not avoided, could result in serious injury or death, and will void the warranty.

The manufacturer cannot anticipate every circumstance that might involve a potential hazard. Each installation has its own specialized characteristics, requirements, and possible hazards. Therefore, all possible incidents are not included in these warnings. Proper and safe installation, operation, and service are the responsibility of the professional service technician.

Proper care of the water heater is the user’s responsibility. Ensure the user carefully reads and understands the User’s Information Manual before operating and maintaining the water heater.

Make sure the user knows the location of the gas shut-o valve and how to operate it. Immediately close the gas shut-o valve if the water heater is subjected to re, overheating, ood, physical damage, or any other damaging condition that might aect the operation of the unit. Have the water heater checked by a qualied technician before resuming operation.

Do not power up the unit unless the gas and water supply valves are fully opened. Make sure the fresh air intake ports and exhaust gas port are open and functional.

No one but a professional service technician should attempt to install, service, or repair this water heater. There are no serviceable parts which can be changed by the user / owner. User / Owner: Contact the original professional service technician if the water heater needs repair or maintenance. If the original technician is unavailable, ask your gas supplier for a list of qualied service providers.

Keep the area around the water heater clean and free of all materials that can burn. DO NOT store or place gasoline, oils, spray paint, or other ammable products near the water heater.

DO NOT use spray paint, hair spray, or any other ammable spray near the water heater or near the exterior fresh air intake port. DO NOT place any items in or around the exhaust gas outlet port and/ or fresh air inlet ports that could restrict or block the ow in or out of the vent system.

After installation, all water heater safety devices should be tested.

DO NOT store or place newspapers, laundry, or other combustible items near the water heater or the exhaust gas outlet and/or fresh air inlet ports.

The owner should inspect the system monthly for damage, water stains, signs of rust, corrosion, and exhaust vent and air intake blockage. If inspection of the unit shows signs of damage, the water heater should be shut o until the problem is repaired by a qualied technician.

This water heater is certied for outdoor installations only. The water heater consists of gas ignition system components which must be protected from water (dripping, spraying, etc.) during operation and service. Ensure water heater cover is installed at all times when the unit is in operation. Carefully consider installation location and the placement of critical components (circulators, condensate neutralizers, etc.) before installing the water heater.

DO NOT allow children to operate this unit. DO NOT use this unit if it does not appear to be operating correctly. A qualied technician should service and inspect the water heater annually.

The water heater temperature is factory set to 125oF (51.7oC). To avoid scalding, always check the temperature of the hot water before bathing, showering, washing, etc. DO NOT adjust the water temperature while the water heater is being used by other persons.

Any claims for damage or shortage in shipment must be led immediately against the transportation company by the consignee.

This water heater provides a overheat shutdown limit. In the event the water heater water exceeds the set point of the control limit, the cuto will trip and the water heater will shut down. Certain local codes require additional temperature limits. In addition, certain types of systems may operate at temperatures below the minimum set point of the limit provided with the water heater. Contact the manufacturer for additional overheat controls.

NOTE: When inquiring about service or troubleshooting, reference the model and serial numbers from the water heater rating label.

DO NOT USE THIS WATER HEATER IF ANY PART HAS BEEN SUBMERGED IN WATER. Immediately call a qualied service

technician. The water heater MUST BE replaced if it has been submerged. Attempting to operate a water heater that has been submerged could create numerous harmful conditions, such as a potential gas leakage causing a re and/or explosion, or the release of mold, bacteria, or other harmful particulates into the air. Operating a previously submerged water heater could result in property damage, severe personal injury, or death. NOTE: Water heater damage due to ood or submersion is considered an Act of God, and IS NOT covered under product warranty.

NOTE: If the water heater is exposed to the following, do not operate. Immediately call a qualied service technician.

1. Fire

2. Damage

3. Submerged in Water Failure to follow this information could result in property damage, severe personal injury, or death.

DO NOT alter or modify the water heater or water heater controls. Altering any HTP water heater with parts not manufactured by HTP WILL INSTANTLY VOID the water heater warranty and could result in property damage, personal injury, or death.

This water heater has been designed to heat potable water ONLY. Using this water heater to heat non-potable uid WILL VOID product warranty, and could result in property damage, personal injury, or death.

Do not use this water heater for anything other than its intended purpose (as described in this manual). Doing so could result in property damage and WILL VOID product warranty.

B. Improper Combustion

Do not obstruct the ow of combustion and ventilating air. Adequate air is necessary for safe operation. Failure to keep the exhaust vent and combustion air intake clear of ice, snow, or other debris could result in property damage, serious personal injury, or death.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 6

C. Gas

Should overheating or gas supply fail to shut o, turn o the manual gas control valve to the water heater.

D. When Servicing the Water Heating System

Be sure to disconnect electrical power before opening water heater cabinet or performing service. Label all wires while performing service to ensure proper re-wiring of the water heater. Wiring errors can cause improper or dangerous operation. Failure to do so could result in an electrical shock, improper water heater operation, property damage, serious personal injury, or death.

• To avoid electric shock, disconnect electrical supply before performing maintenance.

• To avoid severe burns, allow water heater and associated equipment to cool before servicing.

• Do not use petroleum-based cleaning or sealing compounds in a water heating system. Gaskets and seals in the system may be damaged. This can result in substantial property damage.

• Do not use “homemade cures” or “patent medicines”. Damage to the water heater, substantial property damage, and/or serious personal injury may result.

• Always verify proper operation after servicing the water heater.

NOTE: When inquiring about service or troubleshooting, reference the model and serial numbers from the water heater rating label.

E. Water Chemistry Requirements

Chemical imbalance of the water supply may aect eciency and cause severe damage to the appliance and associated equipment. Water quality must be professionally analyzed to determine whether it is necessary to treat the water. Various solutions are available to adjust water quality. Adverse water quality will aect the reliability of the system. In addition, operating temperatures above 135oF will accelerate the build-up of lime scale and possibly shorten appliance service life. Failure of an appliance due to lime scale build-up, low pH, or other chemical imbalance IS NOT covered by the warranty.

The water must be potable, free of corrosive chemicals, sand, dirt, and other contaminates. It is up to the installer to ensure the water does not contain corrosive chemicals or elements that can damage the heat exchanger. Potable water is dened as drinkable water supplied from utility or well water in compliance with EPA secondary maximum contaminant levels (40 CFR Part 143.3). If the water contains contaminants higher than outlined by the EPA, water treatment is recommended and additional, more frequent maintenance may be required. See Table 1.

If you suspect that your water is contaminated in any way, discontinue use of the appliance and contact an authorized technician or licensed professional.

Contaminant Maximum Allowable Level

Total Hardness

(Commercial Use - Below 140oF

water temperature)

Total Hardness

(Commercial Use - Above 140oF

water temperature)

Aluminum 0.05 to 0.2 mg/l or PPM

Chloride 100 mg/l or PPM

Copper 1 mg/l or PPM

Iron 0.3 mg/l or PPM

Manganese 0.05 mg/l or PPM

pH 6.5 - 8.5

Sulfate 205 mg/l or PPM

Total Dissolved Solids (TDS) 500 mg/l or PPM

Zinc 5 mg/l or PPM

Dissolved Carbon Dioxide (CO2) 15 mg/l or PPM

Table 1 - Water Quality Specications

200 mg/l

(12 grains/gallon)

120 mg/l

(7 grains/gallon)

F. Freeze Protection

This water heater is designed to automatically prevent freezing to temperatures of 5oF (-15oC). This freeze protection is not eective if the power fails. In order for freeze protection to operate, the water heater must be powered at 120 VAC. Additional freeze protection must be used if the water heater is installed where temperatures can reach freezing conditions of 5oF (-15oC) or below. In addition, the water heater’s freeze prevention devices will not prevent the external plumbing from freezing. Protect external plumbing with insulation, heat tape, heaters, solenoids, or pipe covers. Failure to follow these instructions could result in water heater failure and substantial property damage.

Consider piping and installation when determining heater location. Damages resulting from incorrect installation or from use of products not approved by HTP ARE NOT covered by warranty.

NEVER use any toxic chemical, including automotive, standard glycol antifreeze, or ethylene glycol made for hydronic (nonpotable) systems. These chemicals can attack gaskets and seals in water systems, are poisonous if consumed, and can cause personal injury or death.

The water heater control is equipped with freeze protection that activates based on internal water temperature. See the table below for details on freeze protection operation. NOTE: Freeze protection will not be active if the water heater loses power.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 7

Freeze Protection Operation

Stage 1 - If control detects water temperature of 46oF

(8oC) and below, it turns the internal and external

System Freeze

Protection

(Activates

Based on

Internal Water

Temperature)

Table 2 - Freeze Protection Detail

pumps On for 600 seconds and O for 30 seconds. This cycle repeats until the control detects inlet water temperature of 50oF (10oC) and above.

Stage 2 - If control detects water temperature of 41oF (5oC) and below, it turns the burner on to meet a target temperature of 104oF (40oC). The burner and internal and external pumps will continuously during this stage until the control detects inlet water temperature of 104oF (40oC) and above.

Stage 3 - If control detects water temperature of 34oF (1oC) and below, Er: 85 will appear on the display.

NOTE: Damages resulting from incorrect installation or from use of products not approved by the manufacturer ARE NOT covered by warranty.

G. Water Temperature Adjustment and Scalding

This water heater can deliver scalding water. Be careful whenever using hot water to avoid scalding injury. Certain appliances such as dishwashers and automatic clothes washers may require increased water temperatures. By setting the thermostat on this heater to obtain the increased water temperature required by these appliances you may create the potential for scald injury.

To protect against injury, install a mixing valve in the water system. This valve will reduce point of use discharge temperatures by mixing cold and hot water in branch supply lines. Such valves are available from your local plumbing supplier.

Table 3 details the relationship of water temperature and time with regard to scald injury and may be used as a guide in determining the safest water temperature for your applications.

Approximate Time / Temperature Relationships in Scalds

120oF More than 5 minutes

125oF 1 1/2 to 2 minutes

130oF About 30 seconds

135oF About 10 seconds

140oF Less than 5 seconds

145oF Less than 3 seconds

150oF About 1 1/2 seconds

155oF About 1 second

Table 3 - Time and Temperature Relationship in Scalds

An ASSE 1017 or ASSE 1070 temperature limiting or mixing valve is recommended in installations servicing disabled or elderly persons, or children. Mixing valves do not eliminate the risk of scalding. To avoid scalding:

• Set the water heater set point temperature as low as possible.

• Feel water before bathing or showering.

• If thermostatic valves are required, use devices specically designed for such purpose. Install these devices in accordance with instructions provided by the manufacturer.

Failure to install a temperature limiting or mixing valve and follow these instructions could result in property damage, severe personal injury, or death due to scalds.

Households with small children, disabled, or elderly persons may require a 120oF or lower temperature setting to prevent severe personal injury or death due to scalding.

H. High Elevation Installations

Natural gas at high elevation might contain less heating value than typical 1,000 BTU/cu ft and therefore can cause improper air / gas mix leading to improper combustion. For natural gas installations above 3,000 ft, call your gas provider to determine the heating value of the supplied natural gas.

Part 2 - Before You Start

Open the shipping crate of the water heater.

UNCRATING THE WATER HEATER - Any claims for damage or shortage in shipment must be led immediately against the transportation company by the consignee.

A. What’s in the Box

Components included with the water heater:

Item Description Quantity

Hybrid Water Heater 1

User and Installation Manuals 1 each

Condensate Hose

(Part # - 7855P-089)

Anchors and Wall Mounting Bracket

(7850P-084)

Spare Parts Kit

(Gaskets and O-Rings)

(7855P-383)

LP Conversion Kit

(7855P-452)

150 PSI Pressure Relief Valve

(7850P-103)

Cascade Communication Cable

(7850P-093)

Table 4 - Included with the Water Heater

One (1)

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 8

B. Optional Equipment

Optional equipment available from HTP (and Part #):

Optional Parts

Flow Switch (7860P-013)

System Sensor

(7250P-324)

Indirect Tank Sensor

(7250P-325)

Table 5 - Optional Equipment

Other Optional Equipment

Below is a list of other optional equipment available from HTP. These additional options may be purchased through your HTP distributor:

• Condensate Neutralizer (Part # 7450P-212)

• Condensate Removal Pump (Part # 554200) NOTE: When using an optional system sensor, pipe insulation must be wrapped around it to improve temperature measurement accuracy and increase overall system eciency.

One (1)

Part 3 - Prepare the Water Heater Installation

Remove all sides of the shipping crate to allow the heater to be moved into its installation location.

COLD WEATHER HANDLING - If the water heater has been stored in a very cold location (BELOW 0oF) before installation, handle with care until the components come to room temperature. Failure to do so could result in damage to the water heater.

Carefully consider installation when determining heater location. Please read the entire manual before attempting installation. Failure to properly take factors such as heater venting, piping, condensate removal, and wiring into account before installation could result in wasted time, money, and possible property damage and personal injury.

A.Choosing an Outdoor Installation Location

These heaters are design certied for outdoor installations. Heaters must not be installed under an overhang unless clearances are in accordance with local codes, the requirements of the gas supplier / utility, and the AHJ. Three sides must remain open in the area under the overhang. Roof water drainage must be diverted away from heaters installed under overhangs. Failure of heater or components due to incorrect operating conditions IS NOT covered by product warranty.

Incorrect ambient conditions can lead to damage to the heating system and put safe operation at risk. Ensure that the installation location adheres to the information included in this manual. Failure to do so could result in property damage, serious personal injury, or death. Failure of heater or components due to incorrect operating conditions IS NOT covered by product warranty.

This water heater must be installed upright in the vertical position as described in this manual. DO NOT attempt to install this water heater in any other orientation. Doing so will result in improper water heater operation and property damage, and could result in serious personal injury or death.

When installing the heater outdoors, ensure the installation location is not near the exhaust or intake terminations of other gas-red products – boilers, water heaters, furnaces, etc. Failure to do so could result in the recirculation of exhaust fumes. Exhaust recirculation could result in a hazardous condition and cause substantial property damage, severe personal injury, or death.

1. Outdoor Installation Area Operating Conditions

• Heater must be placed in an area where the exhaust plume will not be recirculated into the louver system located on the front access panel. Avoid fences or walls that extend above the exhaust vent termination. Pipe the exhaust vent so that it terminates level with or above the fence, wall, or enclosed area.

• Do not install heaters in locations where rain from building runo may spill onto the heater. Doing so could result in premature product failure. Such failures ARE NOT covered by warranty.

• Do not locate where sprinklers may spray directly onto the heater cabinet and possibly into the louvers, which could damage the control system and internal components of the water heater. Such damages ARE NOT covered by warranty.

• Do not install directly on the ground, as the water heater is heavy when lled with water. Install the heater level on a concrete pad, block, or pressure treated wood platform, designed to support the weight of the water heater and components when lled with water. The water heater must be properly supported and installed level in order to operate and drain condensate properly.

• Do not install the water heater under a deck or porch.

• Do not install the water heater in a well, stairwell, alcove, courtyard, or other recessed area.

• Do not install the water heater on stack frames.

• In areas where heater is exposed to sustained temperatures below 32oF, provisions must be made to protect the water heater, condensate lines, and piping from freezing. The use of heat tape is recommended to avoid freezing. It is also recommended to bush up the condensate line size to 1” and terminate condensate discharge line as close to the unit as possible. Longer condensate runs are more prone to freezing.

• Locate heater at least 10’ away from any forced air inlet. Maintain a clearance of at least 48” below or horizontal from any window, door, walkway, or gravity air intake. Never place heater under a porch.

• In areas where it can get extremely hot (over 100oF, it is recommended to install the heater in an area that avoids direct sunlight to keep the internal components cooler. Failure to follow this instruction could lead to premature failure. Such failures ARE NOT covered by warranty.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 9

This water heater has a condensate disposal system that may freeze if exposed to sustained temperatures below 32oF. Precautions should be taken to protect the condensate trap and drain lines from sustained freezing conditions. Failure to take precautions could result in property damage, severe personal injury, or death.

The service life of the water heater’s exposed metallic surfaces, such as the casing, as well as internal surfaces, such as the heat exchanger, are directly inuenced by proximity to damp and salty marine environments. In such areas higher concentration levels of chlorides from sea spray coupled with relative humidity can lead to degradation of water heater components. Take local installation conditions into consideration before installing to prevent premature water heater failure.

2. Check for nearby connections to:

• System water piping

• Gas supply piping

• Electrical power

• Condensate drain

All water heaters eventually leak. Locate the water heater where any leakage from the relief valve, related piping, tank, or connections will not result in damage to surrounding areas or lower oors of the building. Any water heater should be installed in such a manner that if it should leak the resulting ow of water will not cause damage to the area in which it is installed. National Plumbing codes require a drain pan for any water heater installation. Such a drain pan must have a clearance of at least 1.0” (2.5 cm) greater than any point on the water heater’s outer jacket and must be piped to an adequate drain. Leakage damages ARE NOT covered by warranty. Failure to install a drain pan is the sole responsibility of the owner and/or installer. Reference UPC 2000 (Uniform Plumbing Code) Section 510 - Protection from Damage or IPC 200 (International Plumbing code) Section 504 - Safety Devices. Leakage damages ARE NOT covered by warranty. In addition, water leak detection devices and automatic water shuto valves are readily available at plumbing supply houses. IT IS HIGHLY RECOMMENDED BY THE MANUFACTURER TO INSTALL WATER LEAK DETECTION DEVICES AND AUTOMATIC SHUTOFF VALVES IN ANY WATER HEATER INSTALLATION WHERE A LEAKAGE OF WATER COULD RESULT IN PROPERTY DAMAGES.

To conserve water and energy insulate all water piping, especially the hot and recirculation water lines.

3. Check area around heater. Remove any combustible materials, gasoline, and other ammable liquids.

6. Clean and ush system when reinstalling a heater.

Do not connect the water heater to any heating systems or components that have been previously used for non-potable applications.

Do not introduce toxic chemicals, such as antifreeze or water heater treatments, into the water heater or any piping meant for potable water purposes.

Ensure that all piping and components connected to the water heater are suitable for potable water applications.

Do not use this water heater for space heating applications.

Circulators suitable for DHW applications must be used.

NOTE: When installing in a minimum clearance location, it may not be possible to read or view some product labeling. It is recommended to make note of the heater model and serial number.

B. Leveling

In order for the condensate to properly ow out of the collection system, the area where you locate the heater must be level. Location must also fully support the weight of the lled water heater.

C. Clearances for Service Access

See Figure 1 and Table 6 for recommended service clearances. If these minimum clearances are not provided, it may not be possible to service the water heater without removing it from the space.

Recommended Service and Proper Operation Clearances

Top 36 in. (900 mm)

Back 5/8 in. (15.9 mm)

Front 24 in. (609.6 mm) or more

Right Side

Left Side

Bottom

Table 6 - Minimum Installation and Service Clearances

12 in. (304.8 mm) for Wall Mounted Model

Zero Clearance for Floor Mounted Model

NOTE: This appliance is approved for zero clearance to combustible construction.

NOTE: If the water heater is installed in a narrow space or corner, ensure that there is sucient space for service. NOTE: If you do not provide the minimum clearances shown in Table 6 and Figure 1 it might not be possible to service the heater without removing it from the space.

NOTE: In multiple water heater installations, ensure a minimum clearance of 36” from the top of one water heater to the bottom of the next water heater on wall mounted models, and a minimum clearance of 10” from the side of water heater to the next water heater on all models.

6 in. (150 mm)

Failure to keep the water heater area clear and free of combustible materials, liquids, and vapors can result in substantial property damage, severe personal injury, or death.

4. Gas control system components must be protected from dripping water during operation and service.

5. If the heater is to replace an existing heater, check for and correct any existing system problems, such as:

• System leaks

• Location that could cause the system and heater to freeze and leak

• Incorrectly sized expansion tank

Do not locate the water heater where it will be exposed to prevailing winds.

Moisture will be produced by the exhaust vent. Take precautions when determining water heater location. Moisture may fall from the vent termination to the ground and turn to ice in freezing conditions. Moisture or ice can produce a hazardous condition.

Failure to follow these instructions could result in substantial property damage, serious personal injury, or death.

MINIMUM CLEARANCES FROM COMBUSTIBLE MATERIALS

• Hot water pipes - at least 1” from combustible materials

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 10

Always take future maintenance into consideration when locating the water heater. If the water heater is located in an installation location with limited clearances, it may be necessary to remove the water heater from the space to perform maintenance. Failure to consider maintenance when determining installation location could result in property damage.

Figure 1 - Minimum Service Clearances

2 3

Figure 2 - Tankless Water Heater with Outdoor Kit Components

# Description # Description

1 Air Intake Louver 5 Front Cover

2 Air Intake (Behind Exhaust Pipe) 6 LED Status Sight Glass

3 Exhaust Pipe 7 Exhaust Adapter

4 Exhaust Screen 8 Outdoor Enclosure

Table 7 - Installed Components

Indoor

Figure 3 - DO NOT INSTALL THE WATER HEATER INDOORS

D. Exhaust Vent and Air Intake

The heater is rated Category IV (pressurized vent, likely to form condensate in the vent) and requires a special vent system designed for pressurized venting.

NOTE: The venting option described here (and further detailed in the Venting section, this manual) is the lone venting option approved for this water heater. Failure to install the water heater in accordance with the provided venting instructions will void the warranty.

Failure to vent the water heater properly will result in serious personal injury or death.

Do not attempt to vent this water heater by any means other than those described in this manual. Doing so will void the warranty and may result in severe personal injury or death.

The exhaust discharged by this water heater may be very hot. Avoid touching or other direct contact with the exhaust gases of the vent termination assembly. Doing so could result in severe personal injury or death.

Outdoor Installation

This water heater is designed to draw combustion air through the louver system in the heater cabinet. This combustion air also serves to cool the internal electronics when the heater is installed in very warm climates. To prevent combustion air contamination or exhaust recirculation:

• Flue gas can cause damage to exterior walls and other devices.

• Locate the heater at least 48” below or horizontally from any window, door, walkway, or gravity air intake.

• Locate the heater 10’ away from any public area, outdoor sitting area, or forced air inlet.

• Locate the heater away from areas that may change over time. Do not allow the growth of trees, shrubs, or plants to obstruct proper operation of the exhaust vent system.

• If the heater is located in a fenced area, ensure the unit exhaust vent extends level with or above the top of the fence to ensure ue gas does not get trapped and possible recirculated into the louver system, which could contaminate combustion air.

See Venting section for additional details.

E. Carbon Monoxide Detectors

In the Commonwealth of Massachusetts and As Required by State and Local Codes:

Installation of Carbon Monoxide Detectors: At the time of installation or replacement of the vented gas fueled appliance, the installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor level where the gas appliance is installed, unless the

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 11

appliance is located in a detached, uninhabitable structure separate from the dwelling, building, or structure used in whole or in part for residential purposes. In addition, the installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on each additional level of the dwelling, building, or structure served by the vented gas appliance. It shall be the responsibility of the property owner to secure the service of qualied licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that these requirements cannot be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Do not attempt to vent this water heater by any means other than those described in this manual. Doing so will void the warranty and may result in severe personal injury or death.

Approved Carbon Monoxide Detectors: Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 70 and be ANSI/UL 2034 listed and IAS certied.

F. Prevent Combustion Air Contamination

Install intake air piping for the heater as described in the Venting Section, this manual. Do not terminate exhaust in locations that can allow contamination of intake air.

Ensure that the intake air will not contain any of the contaminants in Table 8. Contaminated air will damage the heater, resulting in possible substantial property damage, severe personal injury, or death. For example, do not pipe intake air near a swimming pool or laundry facilities. These areas always contain contaminants.

Products to Avoid

Spray cans containing uorocarbons

Permanent wave solutions Swimming pools

Chlorinated waxes / cleaners Metal fabrication plants

Chlorine-based swimming pool chemicals

Calcium chloride used for thawing

Sodium chloride used for water softening

Refrigerant leaks Auto body shops

Paint or varnish removers Plastic manufacturing plants

Hydrochloric or Muriatic acid

Cements and glues New building construction

Antistatic fabric softeners used in clothes dryers

Chlorine-type bleaches, laundry detergents, and cleaning solvents

Adhesives used to fasten building products

Table 8 - Products and Areas Likely to Have Contaminants

NOTE: DAMAGE TO THE HEATER CAUSED BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY WARRANTY. (Refer to

the limited warranty for complete terms and conditions.)

Areas Likely to Have

Contaminants

Dry cleaning / laundry areas and establishments

Beauty shops

Refrigeration repair shops

Photo processing plants

Furniture renishing areas and establishments

Remodeling areas

Garages and workshops

Figure 4 - CO Warning Label

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 12

G. Technical Specications

Model 199

Installation Outdoor, Wall Mounted Model or Floor Model, Fully Condensing

Minimum / Maximum Input (Btu/Hr) 19,900 / 199,000

Uniform Energy Factor (UEF) / Thermal

Eciency (TE)

Flue System Category IV, Sealed Combustion Direct Vent, Power Vent

Weight (lbs)

Orice Size

Gas Supply

Pressure

Manifold

Pressure

Power

Supply

General Operating Conditions

Ignition System Direct Electronic Ignition / Automatic Flame Sensing

Burner System Single Orice Premixed Fuel Modulation / Ceramic Fiber Burner

Gas Valve System Air Ratio Valve

Minimum Flow Rate Zero activation with storage tank

Internal Pipe Material Copper

Dimensions

Heat Exchanger Water Capacity (DHW) 3.5 Gallons

Control Panel / Main Controller P-950CH / NGTH-10CH

Water Pressure Min 12 - Max 150 PSI

DHW Setpoint Temperature Range 95 – 160oF (35 – 71oC)

Connection

Sizes

Materials

Table 9 - Technical Specications

Cold Water Inlet / Hot

Safety Devices

Wall Mount 120

Floor Model 150

NG 8.3 mm (0.327”)

LP 6.35 mm (0.250”)

Min (3”) NG: 0.003” / LP: 0.004” WC

Max (3”) NG: -0.19” / LP: -0.20” WC

Main Supply 120V 60 Hz, 6A

Maximum Power

Consumption

Minimum Ambient Temperature: -5oF (-20.5oC)

Shipping and Storage Temperature Range: -4 – 176oF (-20 – 80oC)

Power Supply and Communication (CN4): 14V DC

Product Approvals and Requirements

Wall Mount W 20” - H 38.8” - D 18”

Floor Model W 20” - H 50.7” - D 19.5”

Water Outlet

Gas Inlet 3/4” NPT

Cabinet Cold Rolled Carbon Steel

Heat Exchanger 316L Stainless Steel

Optical Flame Sensor, Burner Plate High Limit (392oF), Water Temperature High Limit Sensor (203oF), Water Leak Detection, Freeze Protection (Three Stage Operation - Activates at 46oF – See Freeze Protection in Installer Menu for Details), Exhaust Temperature High Limit Sensor (190oF), Flue Air Pressure Switch, Condensate Switch, Built-In Low Water CutO Probe

0.92 / 95%

3.5” to 14” WC

160W

EMC: 89/336/EEC

LVD: 73/23/EEC

1 1/4” NPT

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 13

Peak Hour Demand / First Hour Rating

Use Average Gallons of Hot Water per Usage Times Used During 1 Hour Gallons Used in 1 Hour

Shower 20 X =

Bath 20 X =

Shavings 2 X =

Hands and Face Washing 4 X =

Hair Shampoo 4 X =

Hand Dishwashing 4 X =

Automatic Dishwasher 14 X =

Food Preparation 5 X =

Wringer Clothes Washer 26 X =

Automatic Clothes

Washer

32 X =

Total Peak Hour Demand (FHR) =

Table 10 - Peak Hour Demand Worksheet - *This worksheet assumes no water conservation measures

Input Rate

(BTU/hr)

Delta-T (F)

Continuous Draw

(GPH)

80 Gallons FHR 119 Gallons FHR 175 Gallons FHR

Storage Tank Sizes

40 567 627 657 699

50 454 514 543 585

60 378 438 468 510

70 324 384 413 455

80 284 344 373 415

199,000

90 252 312 341 383

100 227 287 316 358

110 206 266 296 338

120 189 249 278 320

130 175 235 264 306

140 162 222 251 293

Table 11 - Recovery Rating - NOTE: First Hour Rating can be increased by using an external mixing valve and increasing tank setpoint temperature. Example: If installation requires 120F from Mixing Valve, set tank at 140F to increase First Hour Rating.

All Calculations are Based on 100oF Temperature Rise First Hour Rating with Storage Tank

# of Water

Heaters

1 1 199,000

# of Storage

Tanks

Input Rate

(BTU/Hr)

Pressure Drop

at 20 GPM

Continuous Draw (GPH)

Gallons

119

Gallons

227 287 317 359

175

Gallons

2 1 398,000 455 515 544 586

3 1 597,000 682 742 772 814

4 1 796,000 910 970 999 1,041

15 Feet of Head

1 2 199,000 227 347 406 490

2 3 398,000 455 635 723 849

Table 12 - Recovery Rating - NOTE: First Hour Rating can be increased by using an external mixing valve and increasing tank setpoint temperature. Example: If installation requires 120F from Mixing Valve, set tank at 140F to increase First Hour Rating.

Total Input Rate x Thermal Eciency First Hour Rating (FHR) = (Outlet Temperature - Inlet Temperature) x 8.31 + .75 x Total Storage

Example: 2 CGH-199W Water Heaters Input Rate = 398,000 BTU/Hr Thermal Eciency = 95%, Outlet Temperature = 140oF, Inlet Temperature = 40oF, 2 Storage Tanks (80 Gallons Each) = 160 Gallons

FHR = 398,000 x .95 + .75 x 160 (140-40) x 8.31

FHR = 378,100 + 120 831 FHR = 455 + 120 = 575 Gallons

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 14

Figure 5 - Wall Model Dimensions

Figure 6 - Floor Model Dimensions

A Air Intake -

B Exhaust Vent -

C DHW Outlet Adapter 1 1/4” NPT

D DHW Inlet Adapter 1 1/4” NPT

E Gas Inlet Adapter 3/4” NPT

F Condensate Adapter 1/2” NPT (3/4” PVC Socket on Floor Models)

Table 13 - Adapter Specications

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Description Diameter

Page 15

Figure 7 - Components

Number Component Description Number Component Description Number Component Description

1 Automatic Air Vent 13 High Voltage Terminal Block 25 Water Inlet Pipe

2 Top Water Outlet Adapter 14 Gas Inlet Pipe to Gas Valve 26 Ignition Transformer

3 Gas Valve 15 Water Outlet Pipe 27 Flame Detection Sensor

4 Intake Hose 16 Gas Inlet Adapter 28 Sight Glass

5 Gas Inlet Pipe to Mixer 17 Bottom Water Outlet Adapter 29 Igniter Rod

6 Air/Gas Mixer 18 Pressure Gauge 30 Flue Air Pressure Switch

7 Burner High Limit Switch 19 Bottom Water Inlet Adapter 31 BLDC Fan

8 Heat Exchanger Temperature Sensor 20 Condensate Trap 32 Exhaust Pipe

9 Low Water Level Probe 21 Condensate Outlet Adapter 33 Top Water Outlet Adapter

10 Main Control Board 22 Condensate Air Pressure Switch 34 Exhaust Vent Adapter

11 Control Panel 23 Low Voltage Terminal Block 35 Air Intake Pipe Adapter

12 Manual ON/OFF Power Switch 24 Heat Exchanger

Table 14 - Component List

How the Water Heater Operates

Condensing technology intelligently delivers water heating while maximizing eciency. Outlined below are the features of the system and how they operate: Stainless Steel Heat Exchanger - The highly ecient 316L stainless steel re tube heat exchanger with internal aluminum is designed to extract all available heat from the combustion process and pass it into heat transfer uid. The stainless steel construction provides protection for longer service life. The heat exchanger oers greater water content, providing lower system pressure and greater overall system eciency. 10 to 1 Modulating Combustion System - The combustion system is specially designed to provide very high turn down. This combustion system will modulate the burner output to very low

levels to match the system demand and achieve better overall control of the heating system for maximum eciency and reliability. Control – The integrated control system monitors the system and responds to internal and external signals to regulate fan speed and control output. This allows the water heater to deliver only the amount of hot water required and nothing more. The control can regulate the output of multiple water heaters through its cascade system function by establishing one water heater as the master and the other connected water heaters as followers. The master water heater requires a sensor to provide feedback on set point temperature in order to adjust heating output from the connected water heaters. Multiple water heater cascaded systems oer greater system turndown and redundancy.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 16

Electronic LCD Display – The high resolution display allows the user to monitor water heater functions. The display also provides the means to program the system parameters to maximize the eciency of the system design.

Combustion System (Blower – Gas Valve – Mixer – Burner – Spark Ignition) – The highly ecient spark ignition combustion system uses

a variable speed blower to adjust combustion as the system requires more or less energy. The negative regulated gas valve provides only the amount of fuel required to ensure clean combustion. The mixer accurately regulates the combination of gas and air throughout the modulating range to ensure high reliability. The burner is constructed of durable ceramic metal ber for long service life. Water Heater Sensors (Inlet – Outlet – Flue - System) - Sensors provide highly accurate temperature monitoring to ensure accurate system control. These sensor inputs can be monitored through the water heater control system and display.

Pressure Gauge – Allows the user to monitor system pressure. System Safeties – The water heater is provided with many safety

features to ensure reliable and safe operation. Each safety is connected to the water heater control. The water heater will alert the user if an unsafe condition occurs and needs to be addressed. The following are provided safeties: Flue Pressure Switch (monitors ue pressure), Burner High Limit (monitors burner plate temperature), High Limit Water Switch (monitors water heater water temperature), Low Water Sensor (monitors water level in the heat exchanger), optic ame sensor (monitors ame quality), Flue Sensor (monitors ue temperature), Condensate Pressure Switch (monitors pressure to ensure condensation does not back up into water heater). Manual Air Vent – Each water heater is equipped with an air vent to discharge air from the system during start–up. 1 ¼” Inlet and 1 ¼” Outlet Connection – Water heaters are equipped with bottom piping connections. Gas Connection – The water heater is equipped with a ¾” gas connection to connect the incoming gas supply. Field Wiring and Power Switch – Each water heater is supplied with a power switch to cut o power. The water heater is also equipped with two front mounted terminal strips. These terminal strips are separated into low and line voltage to ease system wiring. Condensate Trap and Hose Assembly – Each water heater has a builtin condensate trap to control the discharge of condensate produced by the water heater during normal operation. A corrugated condensate hose is also provided to ensure proper drainage of condensate into the pump or drain. Low Water Cut O Probe – LWCO is provided with each water heater to ensure the heater has an adequate water level to eliminate overheating and damge to the heat exchanger. Pump Service Mode – Allows manual operation of pumps to commission system and check pump operation. Cascade Operation - This water heater can be congured to run with multiple units in a Cascade System. In a Cascade System, multiple water heaters are installed, piped, and wired to cooperate in a single system. This provides many advantages over a single large capacity water heater, including increased turndown, system redundancy, and increased eciency. A maximum of sixteen (16) water heaters can be controlled by a single water heater designated as the “Master”. Other connected water heaters are designated as “Followers”. A DHW sensor / aquastat / or system sensor must be wired to the Master unit. The Master controls the operational run time of the connected Followers and modulates the connected units up or down to ensure the units are putting only the needed energy into the connected storage tank, and also to ensure all connected units get even run time to balance out service requirements. When the Master water heater receives a call for heat from the DHW sensor / aquastat / or system sensor, the Master will energize the lead water heater in the cascade system. In a new system start-up this will be the Master. The water heater will re at its ignition speed and then modulate its ring rate to maintain the set point. If the rst water

heater reaches 80% of its ring rate, the Master will modulate down and split the load in half with the next unit in the system service rotation. At this point, the Master will re the second water heater in the system. If there are more than two water heaters in the system, the same principle will be applied. Once the lead water heater reaches 80% of its ring rate, it will modulate down and split the total amount of load by the total number of units in the cascaded system. If the set point still cannot be met, the Master will continue ring more Followers until either the heat demand is met or all water heaters in the cascade system are ring at the maximum rate. As the heat demand decreases, all operating water heaters will modulate down according to the heating load. The rst water heater to modulate down to 30% will shut o. The same principle will be applied to the remaining water heaters in operation until the setpoint of the storage tank is satised. When the demand is satised, the water heaters will turn o. If 0-10V is used, connect the 0-10V to the low voltage terminals provided on the Cascade Master. The set point will be determined based on the programmed parameters. If 0-10V is not used, a xed temperature set point can be programmed into the control.will turn o.

When installing a cascaded system, it is important that the water heaters are the same model. Failure to ensure the water heaters are the same model will result in improper system operation, wasted time, money, and possible property damage and personal injury. Such damages ARE NOT covered by product warranty.

H. Wall-Mounting

The water heater must be installed on a wall that can bear its weight (more than 100 lbs. when fully plumbed and full of water). Installing the water heater on a wall which cannot support its weight could result in property damage, personal injury, or death.

The water heater may be installed on any suitable internal wall (suitable sound-proong may be required when installing onto a stud partition wall).

This water heater is too heavy for one person to lift. It is highly recommended to install the water heater with two people. Use caution as to not drop the water heater, which could damage the water heater and cause property damage and/or severe personal injury. Verify that the water heater is properly and securely mounted before leaving unsupervised. Failure to comply with the above and properly mount the water heater could result in substantial property damage, severe personal injury, or death.

This wall mounting system is not seismic rated and should not be applied as such. Failure to comply with the above and properly mount the water heater could result in substantial property damage, severe personal injury, or death.

Positioning the Water Heater on the Wall

1. Attach the wall bracket on the location where you want to install the water heater. Ensure it is level and on stud (16” centers) before proceeding.

2. Mark the four drill holes with a pencil or marker. Remove the wall bracket.

3. Drill four (4) holes using a 5/32 drill bit at the marked hole locations.

4. Mount the wall bracket to the wall with the four (4) included anchor bolts. Ensure the mounted bracket is level. See Figure

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 17

8A.

5. Align the heater bracket grooves on the back of the water heater with the tongues on the wall bracket and hang the water heater on the bracket. See Figure 8B.

Figure 8 - Wall-Mounting the Water Heater

Part 4 - Water Piping

Failure to follow the instructions in this section WILL VOID the warranty and may result in property damage, severe personal injury, or death.

DO NOT pipe this water heater with black iron, galvanized steel, steel, or lead pipe. Doing so will result in premature product failure and property damage, and WILL VOID the warranty.

Do not apply a torch within 12” of the water heater. If sweat connections are used, sweat tubing to the adapter before tting adapter to the water connections on the heater. Damages due to improper installation practices ARE NOT covered by warranty.

Dielectric unions or galvanized steel ttings must not be used in a system with this water heater. Doing so WILL VOID the warranty. Use only copper, brass, or stainless steel ttings. Teon thread sealant must be used on all connections.

A. General Plumbing Guidelines

Use two wrenches when tightening water piping at heater. Use one wrench to prevent the heater inlet or outlet line from turning. Failure to prevent piping connections from turning could cause damage to heater components.

The heater control module uses temperature sensors to provide both high limit protection and modulating temperature control. The control module also provides low water protection by sensing the water level in the tank. Some codes / jurisdictions may require additional external controls.

The domestic water connections must be installed in accordance with all local and national plumbing codes, or any applicable standard which prevails. The inlet (cold), outlet (hot), and recirculation inlet ports are 3/4” on all models.

• Pipe material must be suitable to meet local codes and industry standards.

• The pipe must be cleaned and without blemish before any connections are made.

• Isolation (shuto valves) should be used to ease future servicing.

• All water piping should be insulated.

It is recommended to install a sweat shut-o valve and a union in the cold inlet piping and hot outlet to ease future servicing. If there is a backow preventer or any type of a no return valve in the system, install an additional tee here, suitable for a potable hot water expansion tank. In the hot outlet, install a suitable adapter to match the tubing of

the plumbing system. A thermal trap or heat trap loop may be installed here to provide additional energy savings and prevent the thermal siphoning of domestic hot water.

B. Backow Preventer

Use a backow preventer specically designed for water heater installations. This valve should be installed on the cold water ll supply line per local codes.

C. Potable Expansion Tank

A potable hot water expansion tank is required to oset heated water expansion. In most city plumbing systems, the water meter has a no return or back ow device built into the system to prevent back owing of water into city mains. Some local codes require back ow preventers on all incoming water supplies. The hot water expansion tank must be listed for potable water use. The expansion tank should be located on the cold inlet piping close to the water heater.

Expansion Tank

1. Ensure that the potable expansion tank is sized to correctly handle water heater (3.5 gallon capacity), related piping, and connected storage volume and system temperature.

Undersized expansion tanks cause system water to be lost from the relief valve, causing make-up water to be added. Eventual heater failure can result due to excessive make-up water addition. SUCH

FAILURE IS NOT COVERED BY WARRANTY.

The expansion tank must be suitable for hot potable water systems.

2. The expansion tank must be located as shown in Applications, this manual, or following recognized design methods. See expansion tank manufacturer’s instructions for details.

D. Piping the Water Heater

Use at least the MINIMUM pipe size for all water heater loop piping This is to avoid the possibility of inadequate ow through the water heater. Using less than the required minimum pipe size and piping could result in system problems, property damage, and premature water heater failure. Such problems ARE NOT covered by product warranty.

Use both thread tape and pipe dope to connect to the 3/4” domestic water inlet and outlet, and recirculation inlet (if applicable). Tankless isolation valves between the city water supply and tank inlet are recommended for ease of service.

E. Applications

Figure 9 - Piping Symbol Legend

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 18

HOT WATER OUTLET

COLD WATER INLET

USED IF SENSOR CANNOT

COLD WATER INLET

USED IF SENSOR CANNOT

COLD WATER INLET

HEATER PUMP WITH INTERNAL CHECK

Figure 10 - Water Heater with Storage Tank - NOTE: Floor Models are supplied with a Built-In Pump NOTES:

1. Minimum pipe size should match connection size. Upsize pipe accordingly if greater ow is required.

2. A thermal expansion tank suitable for potable water must be sized and installed within this piping system between the backow preventer and the cold water inlet.

3. All circulators should have an integral ow check.

4. Drains and shuto valve between water heater and piping will assist in purging air from system.

5. These drawings are meant to demonstrate system piping only. The installer is responsible for all equipment and detailing required by local codes.

6. In Massachusetts, you must install a vacuum relief valve per 248 CMR.

7. Mixing valve application is optional, but recommended to help prevent scalding.

8. Always shut o power to the water heater or isolate the heater from the system if ANY plumbing work is to be done. Running the water heater without water will result in dry-ring.

9. The setpoint of the water heater needs to be at least 20oF higher than the setpoint of the Aquastat / Tank Sensor / System Pipe Sensor. NOTE: The preferred installation requires that an Aquastat or Tank Sensor be installed in a sensor well provided on the storage tank. If a sensor well is not available, a System Pipe Sensor may be installed on the return piping near the storage tank. However, when using a System Pipe Sensor, the pump MUST be wired to run continuously. In this conguration, this pump CANNOT BE POWERED BY THE WATER HEATER. NOTE: Pumps must either be installed indoors or be rated for outdoor installations. This statement does not apply to oor mount models with built-in pumps.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 19

HOT WATER OUTLET

COLD WATER INLET

FLOW SWITCH

COLD WATER INLET

Figure 11 - Water Heater with Storage Tank and Optional Flow Switch

NOTES:

1. Minimum pipe size should match connection size. Upsize pipe accordingly if greater ow is required.

2. A thermal expansion tank suitable for potable water must be sized and installed within this piping system between the backow preventer and the cold water inlet.

3. All circulators should have an integral ow check.

4. Drains and shuto valve between water heater and piping will assist in purging air from system.

5. These drawings are meant to demonstrate system piping only. The installer is responsible for all equipment and detailing required by local codes.

6. In Massachusetts, you must install a vacuum relief valve per 248 CMR.

7. Mixing valve application is optional, but recommended to help prevent scalding.

8. Always shut o power to the water heater or isolate the heater from the system if ANY plumbing work is to be done. Running the water heater without water will result in dry-ring.

9. The setpoint of the water heater needs to be at least 20oF higher than the setpoint of the Aquastat / Tank Sensor / System Pipe Sensor. NOTE: The preferred installation requires that an Aquastat or Tank Sensor be installed in a sensor well provided on the storage tank. If a sensor well is not available, a System Pipe Sensor may be installed on the return piping near the storage tank. However, when using a System Pipe Sensor, the pump MUST be wired to run continuously. In this conguration, this pump CANNOT BE POWERED BY THE WATER HEATER. NOTE: A FLOW SWITCH IS NOT REQUIRED FOR THIS INSTALLATION, but may be required by local codes or installation requirements. Adding a ow switch INCREASES PRESSURE DROP through the water heater. NOTE: Pumps must either be installed indoors or be rated for outdoor installations. This statement does not apply to oor mount models with built-in pumps.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 20

Figure 12 - Cascaded Water Heaters w/Storage Tank, Individual Pumps, and Recirculation - NOTE: Floor Models are supplied with a Built-In Pump

NOTES:

1. Minimum pipe size should match connection size. Upsize pipe accordingly if greater ow is required.

2. A thermal expansion tank suitable for potable water must be sized and installed within this piping system between the backow preventer and the cold water inlet.

3. All circulators should have an integral ow check.

4. Drains and shuto valve between water heater and piping will assist in purging air from system.

5. These drawings are meant to demonstrate system piping only. The installer is responsible for all equipment and detailing required by local codes.

6. In Massachusetts, you must install a vacuum relief valve per 248 CMR.

7. Mixing valve application is optional, but recommended to help prevent scalding.

8. Always shut o power to the water heater or isolate the heater from the system if ANY plumbing work is to be done. Running the water heater without water will result in dry-ring.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 21

Figure 13 - Cascaded Water Heaters w/ One Storage Tank, System Pump, and Recirculation

NOTES:

1. Minimum pipe size should match connection size. Upsize pipe accordingly if greater ow is required.

2. A thermal expansion tank suitable for potable water must be sized and installed within this piping system between the backow preventer and the cold water inlet.

3. All circulators should have an integral ow check.

4. Drains and shuto valve between water heater and piping will assist in purging air from system.

5. These drawings are meant to demonstrate system piping only. The installer is responsible for all equipment and detailing required by local codes.

6. In Massachusetts, you must install a vacuum relief valve per 248 CMR.

7. Mixing valve application is optional, but recommended to help prevent scalding.

8. Always shut o power to the water heater or isolate the heater from the system if ANY plumbing work is to be done. Running the water heater without water will result in dry-ring.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 22

F. Circulator Sizing

24.00

22.00

20.00

18.00

16.00

14.00

12.00

10.00

Pressure Drop (feet of head)

199 Pressure Drop Curve

8.00

6.00

4.00

2.00

0.00 0 2 4 6 8 10 12 14 16 18 20 22 24

Flow Rate (GPM)

Figure 14 - This chart represents heat exchanger pressure losses.

System Temperature Rise Chart

Model

Minimum

Pipe Size

Flow Rate (GPM) Head (FT) Flow Rate (GPM) Head (FT) Flow Rate (GPM) Head (FT)

20oF ∆T 30oF ∆T 40oF ∆T

199 1 1/4” 18.9 14 12.6 6.5 9.5 4

Table 15 - Water Heater Flow Rates - Recommended Pumps - TACO 0013, Grundfos UP26-99BF

Model

2 3 4 5 6 7 8

Number of Units Cascaded

199 2” 3” 4”

Table 16 - Manifold Pipe Sizes in Inches – NOTE: The above pipe sizes are based on 20oF Delta and maximum water velocity between 5 - 6 ft/s

When installing a cascaded system, ensure the water heaters are the same model. Failure to do so will result in improper system operation, wasted time, money, and possible property damage and personal injury. Such damages ARE NOT covered by product warranty.

G. Pressure Relief Valve

An external pressure relief valve must be installed on this water heater. When installing, observe the following guidelines. Failure to comply with these guidelines can result in substantial property damage, personal injury, or death. This water heater must be provided with an approved 150 psi, ¾” ASME HV Valve that must be installed on the DHW outlet line. The 150 psi Pressure Relief Valve must be installed on the DHW outlet line to ensure a compliant installation and safe operation. This water heater has a high-temperature shut-o switch built in as a standard safety feature. Therefore, a “pressure only” relief valve is required. DO NOT operate this water heater before the supplied pressure relief valve is installed with sucient relieving capacity in accordance with the rating plate on the water heater. Pressure relief valves must be installed as close to the water heater as possible. No other valves should be placed between the pressure relief valve and the appliance. DO NOT install a relief valve with a pressure rating greater than 150 psi. This is the maximum allowable relief valve setting for this water heater.

After installing the relief valve and lling and pressurizing the system, test the operation of the valve by lifting the lever. Make sure the valve discharges freely. If the valve fails to operate correctly, replace it with a new relief valve. Ensure that the maximum BTU/H rating on the pressure relief valve is equal to or greater than the maximum input BTU/H rating of the combination water heater.

Figure 15 - Pressure Relief Valve

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 23

To avoid water damage or scalding due to relief valve operation:

• Discharge line must be connected to relief valve outlet and run to a safe place of disposal. Terminate the discharge line in a manner that will prevent possibility of severe burns or property damage should the relief valve discharge.

• Discharge line must be as short as possible and the same size as the valve discharge connection throughout its entire length.

• Discharge line must pitch downward from the valve and terminate at least 6” above the oor drain, making discharge clearly visible.

• Discharge line shall terminate plain, not threaded, with a material serviceable for temperatures of 375oF or greater.

• Do not pipe discharge to any location where freezing could occur.

• No shuto valve may be installed between the relief valve and water heater or in the discharge line. Do not plug or place any obstruction in the discharge line.

• Test the operation of the relief valve after lling and pressurizing the system by lifting the lever. Make sure the valve discharges freely. If the valve fails to operate correctly, replace it with a new relief valve.

• Test relief valve at least once annually to ensure the waterway is clear. If valve does not operate, turn the water heater “o” and call a plumber immediately.

• Take care whenever operating relief valve to avoid scalding injury or property damage.

• For water heaters installed with only a pressure relief valve, the separate storage vessel must have a temperature and pressure relief valve installed. This relief valve shall comply with Relief Valves for Hot Water Supply Systems, ANSI Z21.22 CSA4.4.

FAILURE TO COMPLY WITH THE ABOVE GUIDELINES COULD RESULT IN FAILURE OF RELIEF VALVE OPERATION, RESULTING IN POSSIBILITY OF SUBSTANTIAL PROPERTY DAMAGE, SEVERE PERSONAL INJURY, OR DEATH.

Do not thread a cap or plug into the relief valve or relief valve line under any circumstances! Explosion and property damage, serious injury, or death may result.

RE-INSPECTION OF RELIEF VALVES: Valves should be inspected AT LEAST ONCE EVERY THREE YEARS, and replaced if necessary,

by a licensed plumbing contractor or qualied service technician to ensure that the product has not been aected by corrosive water conditions and to ensure that the valve and discharge line have not been altered or tampered with illegally. Certain naturally occuring conditions may corrode the valve and its components over time, rendering the valve inoperative. Such conditions can only be detected if the valve and its components are physically removed and inspected. Do not attempt to conduct an inspection on your own. Contact your plumbing contractor for a re-inspection to assure continued safety.

FAILURE TO RE-INSPECT THE RELIEF VALVE AS DIRECTED COULD RESULT IN UNSAFE TEMPERATURE AND/OR PRESSURE BUILD-UP WHICH CAN RESULT IN PROPERT Y DAMAGE, SERIOUS PERSONAL INJURY, OR DEATH.

H. Filling the Heater

The water heater must be full of water and the system fully purged BEFORE powering the water heater. When lling the water heater, open a hot water tap to release air in the water heater and piping. All air has been purged from the system when water runs freely from the faucets. Applying power to the water heater when it is not full of water will damage the heat exchanger, and could result in property damage, serious personal injury, or death. Such damages ARE NOT covered by water heater warranty.

• Ensure any drain valves are completely closed.

• Open the shut-o valve in the cold water supply line.

• Open the hot water faucets to allow air to vent from the heater and piping.

• Allow sucient time for the heater to completely ll with water.

Part 5 - Venting

The heater must be vented as detailed in this section. Ensure the exhaust vent and air intake comply with these instructions regarding vent system. Inspect the installed appliance thoroughly to ensure it complies with all applicable code requirements, as well as the instructions provided in this manual. Failure to properly install the appliance will result in severe personal injury or death.

A. General

This heater is certied as a “Category IV” appliance. This appliance MUST BE INSTALLED OUTDOORS according to the rules outlined in these instructions. Follow the venting instructions carefully. Failure to do so will result in substantial property damage, severe personal injury, or death.

1. Installation should be made in accordance with the regulations of the Authority Having Jurisdiction, local code authorities, and utility companies which pertain to this type of water heating equipment.

2. Install the venting system in accordance with these instructions and with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, CAN/ CGA B149, and / or applicable provisions of local building codes.

3. This water heater must be vented with materials, components, and systems listed and approved for Category IV appliances.

The outdoor enclosure is not designed to carry heavy weight. Do not stack anything on the water heater. Doing so could result in substantial property damage, personal injury, or death.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 24

B. Exhaust Vent and Intake Pipe Location

Vent Terminal

Air Supply Inlet

Area Where Terminal is Not Permitted

Figure 16 - Vent Termination Clearances

Description

B Clearance to window or door that may be opened

C Clearance to permanently closed window *

E Clearance to unventilated sot *

F Clearance to outside corner *

G Clearance to inside corner *

I Clearance to service regulator vent outlet * 3 ft.

K Clearance to a mechanical air supply inlet

L Clearance above paved sidewalk or driveway * 7 ft.

M Clearance under veranda, porch, deck, or balcony * 1 ft.

Table 17 - Vent Termination Clearances NOTE: For clearances not specied in ANSI Z223.1/NFPA 54 or CAN/CSA B149.1, use clearances in accordance with local installation codes and the requirements

of the gas supplier. *Clearance to opposite wall is 24 in.

A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings that serves both dwellings.

Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath oor.

Clearance above grade, veranda, porch, deck, or

balcony

Vertical clearance to ventilated sot located above

the terminal within a horizontal distance of 2 feet from

the center line of the terminal

Clearance to each side of center line extended above

meter / regulator assembly

Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance

(ANSI Z223.1/NFPA 54)

4 ft. below or to side of opening;

1 ft. above opening

4 ft. below or to side of opening;

1 ft. above opening

3 ft. above if within 10 ft. hori-

zontally

12 in.

3 ft. with a height 15 ft. above me-

CANADA

(CSA B149.1)

3 ft.

ter / regulator assembly

3 ft.

6 ft.

The building owner is responsible for keeping the exhaust and intake terminations free of snow, ice, or other potential blockages, as well as scheduling routine maintenance. Failure to keep the vent terminations clear and properly maintain the heater could result in property damage, severe personal injury, or death.

For each oor containing bedroom(s), a carbon monoxide detector and alarm shall be placed in the living area outside the bedrooms. Detectors and alarms shall comply with NFPA 720 (latest edition). Failure to comply with these requirements could result in product damage, severe personal injury, or death.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 25

The outdoor enclosure is not designed to carry heavy weight. Do not stack anything on the water heater. Doing so could result in substantial property damage, personal injury, or death.

C. Water Heater Exhaust Vent and Intake Notes

1. Ensure the water heater is located where it will not be exposed to prevailing winds.

2. Do not locate water heater over public walkways, driveways, or parking lots. Condensate could drip and freeze, resulting in a slip hazard or damage to vehicles and machinery.

3. Moisture build-up may be created in certain installation locations. To save time and cost, carefully consider water heater installation location.

4. The water heater must be installed where vapors cannot make accidental contact with people or pets, or damage shrubs or plants.

5. Do not use the water heater as a shelf or to support any weight.

6. Maximum Snow Level Determination: These installation instructions reference snow levels in establishing a minimum height for the installation of the water heater. Snow levels shall be determined as follows:

a. The installation location may, by ordinance, designate how snow levels are calculated in that location; or b. In the absence of specic ordinances, snow levels shall be calculated from the average monthly maximum depth of snow accumulation as indicated by the National Weather Service’s 10 year statistics for the installation location/geographical area.

In addition:

• The ue products from the exhaust vent will create a large plume when the heater is in operation. Avoid venting in areas that will aect neighboring buildings or be considered objectionable.

• DO NOT locate the water heater in a parking area where it may be damaged by machinery.

• DO NOT vent near sot vents, crawl space vents, or other areas where condensate or vapor could create a nuisance or hazard or cause property damage.

• DO NOT vent where condensate vapor could cause damage or could be detrimental to the operation of regulators, relief valve, or other equipment.

In the Commonwealth of Massachusetts and as Required by State and Local Codes:

• The vented gas fueled appliance shall not be installed so its combustion, ventilation, or dilution air is obtained from a bedroom or bathroom.

• Signage: Whenever any water heater is installed less than seven feet above the nished grade, a metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight feet above grade directly in line with the exhaust vent terminal. The sign shall read, in print no less than 0.5 inches in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

D. Application

Combustion air must be drawn from the outdoors directly into the water heater intake, and exhaust must terminate safely outside. DO NOT INSTALL THIS WATER HEATER INDOORS. Be sure to locate the heater such that the exhaust vent and intake are properly terminated. See Figure 20 and Table 13 for more information. Care must be taken to utilize uncontaminated combustion air. NOTE: To prevent combustion air contamination, see Table 8.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 26

CAUTION

Outdoor Installation

When drawing combustion air from the outdoors, care must be taken to provide adequate freeze protection. Failure to do so could result in property damage and premature product failure. Such damages and failures ARE NOT covered by product warranty.

This water heater is designed to draw combustion air through the louver system in the water heater cabinet. This combustion air also serves to cool the internal electronics when the heater is installed in very warm climates. To prevent combustion air contamination or exhaust recirculation:

• Flue gas can cause damage to exterior walls and other devices.

• Locate the heater at least 48” below or horizontally from any window, door, walkway, or gravity air intake.

• Locate the heater 10’ away from any public area, outdoor sitting area, or forced air inlet.

• Locate the heater away from areas that may change over time. Do not allow the growth of trees, shrubs, or plants to obstruct proper operation of the exhaust vent system.

• If the heater is located in a fenced area, ensure the unit exhaust extends level with or above the top of the fence to ensure ue gas does not get trapped and possibly recirculated into the louver system, which could contaminate the combustion air.

WINDOW

RECOMMENDED CLEARANCE FOR OUTDOOR INSTALLATION

FORCED AIR

INLET

10' MIN.

4' MIN.

4' MIN. 4' MIN.

EXISTING BUILDING

NOTE: DIMENSIONS GIVEN ARE IN FEET.

lp-672-C

Rev. 5.18.18

ENTRY DOOR

LP-672-E

4/5/18

RECOMMENDED OUTDOOR ENCLOSURE

4' MIN.

FENCING SHOULD NOT EXCEED HEIGHT OF THE UNIT

LP-672-F 04/5/18

Heaters must not be installed under an overhang unless clearances are in accordance with local codes, the requirements of the gas supplier / utility, and the AHJ. At a mininum, do not install this water heater under an overhang less than 3 ft (915 mm) from its top or eaves. The area under an overhang must be open to three sides. Roof water drainage must be diverted away from heaters installed under overhangs. Failure of heater or components due to incorrect operating conditions IS NOT covered by product warranty.

Figure 17 - Recommended Outdoor Installation Clearances

lp-673 Rev. 000 Rel. 001 Date 8.30.18

3 ft

(915 mm)

NOTE: IN EXTREMELY HOT CLIMATES IT IS RECOMMENDED TO PLACE THE UNIT ON THE NORTH SIDE OF THE BUILDING TO EXTEND THE LIFE OF THE CONTROLS.

TOP VIEW

Figure 18 - Recommended Outdoor Enclosure

Page 27

Part 6 - Installing the Condensate Drain

This condensing high eciency water heater has a condensate removal system. Condensate is water vapor derived from combustion products, similar to that produced by an automobile when it is initially started. It is very important that the condensate line is sloped down away from the heater and to a suitable drain. The condensate line must remain unobstructed. If allowed to freeze in the line or obstructed in any other manner, condensate can exit from the water heater tee, resulting in potential water damage to property. When installing a condensate pump, select one approved for use with condensing heaters and furnaces. The condensate pump should have an overow switch to prevent property damage from spillage. Condensate from the heater will be slightly acidic (pH from

3.2 to 4.5). Check with your local gas company to determine if combustion condensate disposal is permitted in your area. Install a neutralizing lter if required by local codes. If left untreated and/or improperly disposed of condensate can lead to property damages. DO NOT drain condensate onto nished surfaces. Doing so will damage the surfaces. Damages caused by improper disposal of condensate ARE NOT covered by product warranty.

NOTES:

1. Due to its ecient design, the water heater produces condensate (water) as a normal by-product. This condensate is acidic, with a pH level between 3 and 4. This condensate must be drained away from the water heater and disposed in accordance with all local regulations.

2. The condensate line should be as short and vertical as possible to avoid freezing. If the line must run horizontally, it must be pitched at least 1/4” per foot to properly drain. If this cannot be done, or a very long length of condensate hose is used, increase the condensate line to a minimum of 1” ID and place a tee in the line after the condensate neutralizer to properly reduce vacuum lock in the drain line, or install a condensate removal pump.

3. Use corrosion-resistant materials to drain condensate. Use the included exible plastic hose or ½” PVC and CPVC drain pipe complying with ASTM D1785, F441, or D2665 may be used. Cement

must comply with ASTM D2564 for PVC pipe or F493 for CPVC pipe. For Canadian applications, use CSA or ULC certied PVC or CPVC pipe, ttings, and cement.

4. A frozen condensate line could result in a blocked condition and an Er:29 Error Code. It is very important to protect the condensate line from freezing temperatures or any type of blockage. In installations that may encounter sustained freezing conditions, the use of heat tape is recommended to avoid freezing of the condensate trap and line. It is also recommended to bush up the condensate line size to 1” and terminate condensate discharge as close to the unit as possible. Longer condensate runs are more prone to freezing. Damages due to frozen or blocked condensate lines ARE NOT covered by warranty.

5. Support of the condensate line may be necessary to avoid blockage of the condensate ow.

6. Local building codes may require an in-line neutralizer to be installed (not included) to treat the condensate. If required by local authorities, a condensate lter of lime crystals, marble, or phosphate chips will neutralize slightly acidic condensate (p/n 7450P-212 available from HTP). Follow all the installation instructions included with the neutralizer. If a neutralizer is installed, periodic replacement of the limestone (or neutralizing agent) will be required. The rate of depletion of the limestone varies with usage of the water heater. During the rst year of water heater operation, check the neutralizer every few months for depletion.

7. Route the drain line to a nearby drain or condensate pump. If the heater condensate outlet is lower than the drain, you must use a condensate removal pump (kit p/n 554200 available from HTP).

8. An error will appear on the water heater display if condensate line is blocked - Er: 29. The water heater will not operate with a blocked condensate line. It is extremely important to have this condition repaired by a qualied service technician.

NOTE: INSULATE WITH HEAT TAPE TO PREVENT FREEZING IN THE CONDENSATE TRAP OR LINE.

Figure 19 - Internal Condensate

Trap

LP-672-G

Rev. 5/18/18

1 2

CONDENSATE PIPING

(SUGGESTED SETUP FOR

CONDENSATE REMOVAL

TO FLOOR DRAIN)

IMPORTANT!

WRAP CONDENSATE

VENT

LINES WITH HEAT TAPE OR INSULATION TO PREVENT FREEZING

CONDENSATE HOSE

(SUPPLIED)

1" X 3/4" PVC PIPE

REDUCER - SWEAT

N1100 CONDENSATE

NEUTRALIZER

3/4" PVC PIPE

SWEAT CONNECTIONS

THROUGHOUT

LP-672-A

5/16/18

HORIZONTAL LINES MUST BE INSTALLED WITH A PITCH OF AT LEAST 1/4" PER FOOT

Figure 20 - Condensate Piping with (1) Neutralizer to Drain, and (2) Neutralizer to Pump

PIPE HANGERS MUST BE USED TO SUPPORT PIPING VERTICAL OR HORIZONTAL

TO SUITABLE DRAIN (NO FINISHED SURFACES)

1" x 3/4" PVC PIPE

REDUCER - SWEAT

PIPING SUPPORTS

HORIZONTAL LINES MUST BE INSTALLED WITH A PITCH OF AT LEAST 1/4" PER FOOT

CONDENSATE PIPING WITH PUMP

(SUGGESTED SETUP FOR

CONDENSATE REMOVAL

TO OUTSIDE SOURCE)

IMPORTANT!

WRAP CONDENSATE

VENT

3/4" PVC PIPE SWEAT

LINES WITH HEAT TAPE OR INSULATION TO PREVENT FREEZING

CONNECTIONS

THROUGHOUT

N1100 CONDENSATE NEUTRALIZER

PIPING SUPPORTS

554200 LITTLE GIANT

CONDENSATE PUMP

lp-673 Rev. 000 Rel. 001 Date 8.30.18

TO SUITABLE DRAIN (NO FINISHED SURFACES)

PIPE HANGERS MUST BE USED TO SUPPORT VERTICAL OR HORIZONTAL PIPING

RIGID PVC PIPING

3/4" HOSE BARB

3/4" FLEXIBLE TUBING

LP-672-B

5/16/18

Page 28

Internal Power Switch

Knockout Locations for Wiring to Terminal Blocks

Part 7 - Connecting Electrical Service

Install wiring and electrically ground water heater in accordance with the authority having jurisdiction or, in the absence of such an authority, follow the National Electrical Code, NFPA 70, and/or CSA C22.1 Electrical Code-Part 1 in Canada. Ensure all wiring to the water heater is watertight and protected from the elements. Failure to follow all applicable local, state, and national regulations, mandates, and building supply codes for guidelines to install the electrical power supply could result in property damage, serious personal injury, or death.

ELECTRICAL SHOCK HAZARD – To ensure safety, turn o electrical power supply at service entrance panel before making any electrical connections to avoid possible electric shock hazard. Failure to do so could result in property damage, serious personal injury, or death.

Jumping out control circuits or components WILL VOID product warranty and can result in property damage, personal injury, or death.

It is of extreme importance that this unit be properly grounded. It is very important that the building system ground is inspected by a qualied electrician prior to making this connection. Electrical power must only be turned on when the heater is completely lled with cold water. Failure to follow these instructions could result in component or product failure, serious injury, or death.

8. Do not disconnect the power supply when the water heater is in normal operation. NOTE: For additional electrical protection, the use of a whole house surge protector is recommended. Damage caused by power surges IS NOT covered by the warranty.

L N G

MAIN POWER

Figure 23 - A - Line Voltage Wiring Terminal Block, and B - Terminal Block Wired through Knockout

If the water heater display does not turn on, rst check the plug. Then check the electrical panel circuit breaker and reset if necessary. If the circuit breaker trips again, do not reset. Disconnect the plug and have a qualied technician diagnose the problem.

C. Dip Switches

There is one DIP switch. DIP switches 6 and 7 need to be set to OFF for the water heater to operate normally.

Label all wires prior to disconnecting them when servicing the heater. Wiring errors can cause improper and dangerous operation. Failure to follow these instructions may result in property damage or personal injury.

A. Field Wiring Terminations

All connections made to the water heater in the eld are done to the terminal blocks located inside the front of the unit. Multiple knockout locations are

Figure 21 - Knockout Locations

available to route eld wires into and out of the water heater.

B. Line Voltage Wiring

1. Wiring should be performed by a qualied electrician in accordance with local codes.

2. The heater is limited to a maximum of 8 amps at 120 volts in use.

3. Connect the incoming power wiring to the line voltage terminal strip in the electrical junction box at terminals L (Line Voltage), N (Neutral), and G (Ground) (shown in Figure 30).

4. A line voltage fused disconnect switch may be required, externally mounted and connected according to local codes that may apply.

5. This water heater must be properly grounded. Do not attach the ground wire to either the gas or water piping, or to any other grounding circuits that require a GFCI or AFCI.

6. The wiring diagrams in this manual are to be used for reference purposes only.

7. Refer to these diagrams and the wiring diagrams of any external controls used with the installation when wiring the water heater. Read, understand, and follow all wiring instructions supplied with the controls.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Figure 22 - Internal Manual Power Switch

Figure 24 - Dip Switches

DIP SWITCH OFF ON

1-3 Factory Factory Settings - DO NOT CHANGE

4 Vent Size Factory Settings - DO NOT CHANGE

5 Gas Type LP NG

6 High Fire Normal High Fire

7 Low Fire Normal Low Fire

Table 18 - DIP Switch Group - NOTE: DO NOT CHANGE SWITCHES 1-3. THESE ARE FACTORY SETTINGS.

Maximum Flame Detecting Voltage 2.4V

Pre-Purge Time (Tp) 5 seconds

Safety Time (Igniting Time) (Ts) 1 second

Igniting Interval Time <10 seconds

Post-Purge Time (Tip) 3 minutes

Over-Heating 1, 2, 3, Protection

Detection Time

Temperature Sensor Fault Detection

Time

<2 seconds

<3 seconds

# of Ignition Attempts (Ntl) 5

DHW Setpoint Temperature Range 95 - 160oF (35 - 71.1oC)

Table 19 - System Control Settings - *NOTE: Zero Activation with Internal Recirculation Mode Active

Page 29

Figure 25 - Cascade Wiring Detail

Master Follower

D. Wiring a Cascaded System

When wiring the water heater for Cascade operation, select one as the Master water heater. The remaining water heaters will be designated Followers. See “Setting Up a Cascade System” for more details. Connect the DHW Sensor / aquastat / or system sensor and 0-10V (if used) to the Master. For the Cascade System to work properly a DHW sensor / aquastat / or system sensor must be installed. The DHW sensor / aquastat should be installed in the storage tank; the system sensor should be located as near the storage tank outlet in the cascade system loop as possible. The DHW sensor / aquastat / or system sensor should be wired to the low voltage terminal strip marked for the DHW temp sensor. The Master control will use the water temperature from the sensor to control operation of the Cascade System. If 0-10V is used, the 0-10V should be wired to the low voltage terminal strip marked for the 0-10V. If the 0-10V is connected, the Master control will calculate the water temperature set point based on the programmed reset curve parameters. If the 0-10V is not connected the Master control will maintain the xed water temperature set point programmed into the control.

1. Connect the cascade communication cables to every unit. See Figure

32. Add resistor to the end of the last follower. NOTE: The maximum distance between units is two and a half feet. See Figure 37. This maximum distance can be increased by connecting additional wire harnesses together. However, the number of units that can be cascaded will be reduced by one for every additional harness used. NOTE: It is required to protect the cascade communication cable with a PVC conduit.

2. Every cable comes with one resistor. Use only one resistor on the cascaded system. Discard the rest.

3. Connect the system sensor to the Master low voltage terminal strip. See Figure 37. DHW sensor / aquastat / system sensor / 0-10V must be connected to the Master only. NOTE: The DHW sensor / aquastat / system sensor / 0-10V must be connected to the Master. NOTE: After the cascaded system is set, if you manually turn o the Cascade Master at the display the entire system will shut down. NOTE: After the cascaded system is set, DO NOT turn o a Cascade Follower at the display until you disconnect the cascade cable.

When installing a cascaded system, it is important that the water heaters are the same model.

Failure to follow these instructions will result in improper system operation, wasted time, money, and possible property damage and personal injury. Such damages ARE NOT covered by product warranty.

Figure 26 - Cable Wired to Board

Figure 28 - Maximum Distance Between Wired Cascaded Units - NOTE: It is required to protect the cascade communication cable with a PVC conduit.

Figure 27 - Installed Resistor

MAX 2.5 FEET

Figure 29 - Pump Wiring Detail

Figure 30 - Internal Wiring Terminal Blo cks

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 30

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Figure 31 - Electrical Wiring Diagram

Page 31

Figure 32 - Ladder Diagram

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 32

Connector

No. of Location Pin Board Silk

1 GROUND

2 L Power Supply Line

3 CP1 Heater Pump Power Supply (Live)

4 IT Ignitor Power Supply

CN9

65001WS-12

CN6

LW6A4-03

CN1

SMW250-03

CN4

LWD1140-06

CN8

SMW250-04

CN11

LWD1140-16

Table 20 - Water Heater Wiring 1

5 HEAT/CP2 System Pump Power Supply (Live)

6 GV Gas Valve Power Supply

7 -

8 N Heater Pump Power Supply (Neutral)

9-12 Power Supply (Neutral)

3 NOT USED

2 RS-485 -

3 -

4 RS-485 +

5 RS-485 -

2 GND

3 VDD SELV (14V) DC

4 Fan power (start coil)

5 Fan power (end coil)

6 Fan speed feedback signal SELV (14V) DC

2 ISP / Reset Port

3 ISP TOOL0 Data Port

4 VCC

Description HT Selv

HT (120V~) AC

CP2/3WAY

RS-485 +

RS-485

FAN

MCU ISP

HWL NOT USED

LWL Water Level Sensor

HD NOT USED SELV (5V ) DC

TH Display Control

APS Flue Air Pressure Switch

EL Jumper

BL Burner High Limit

HL Condensate Air Pressure Switch

NOT USED

GND

Cascade

Connection

SELV (5V) DC

SELV (8 - 26V) AC

SELV (5V) DC

SELV (12V~) AC

SELV (14V) DC

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 33

Connector

No. of Location Pin Board Silk

CN7

LWD1140-14

CN14

SMW250-09

CN3

SMW250-06

CN5

SMW250-10

Table 22 - Water Heater Wiring 2

1 - 9 IWM NOT USED

1 - 6 FLUX1 NOT USED

2 GND

Description HT SELV

F.S Flame Sensor

OP.S

DH.S Exhaust Temperature Sensor

I.S Inlet Water Temperature Sensor

BG.S

ST.S Outlet Temperature Sensor

SP.S Overheat Temperature Sensor

RPM

Outlet Operating Water Temperature

Sensor

External DHW Temperature Sensor /

Aquastat

Fan RPM Check

SELV (5V)

Part 8 - Gas Connections

FIRE AND/OR EXPLOSION HAZARD

To avoid serious injury or death, the gas line installation and the gas line inlet pressure test must be done by a licensed professional.

Ensure the gas on which the water heater will operate is the same type specied on the rating plate (natural gas or LP gas). This water heater must be converted into propane operation unless specically manufactured for use with propane. Follow Gas Conversion Manual instructions (separate document). Propane ready water heaters have the sux “LP” after the model serial number. Failure to follow these instructions could result in property damage, personal injury, or death.

Make sure the gas line pressures are within normal limits. Pressures outside normal limits can result in poor performance and hazardous operating conditions. Failure to do so could result in property damage, personal injury, or death.

A. Gas Pipe Sizing Tables

1. Gas Pipe Sizing

This information is for reference use only. Refer to gas pipe manufacturer specications for actual delivery capacity. The DOE standard for Natural Gas is 1100 BTU/ft3. Contact the local gas supplier for actual BTU/ft3 rating.

2. Natural Gas Pipe Sizing

The following table lists maximum capacity of pipe in cubic feet of gas per hour for gas pressures of 14” or less and a pressure drop of 0.5 inches water column, based on a 0.60 specic gravity for natural gas.

Pipe Size (in.)

3/4 360 247 199 170 151 137 117 104 83 71

1 678 466 374 320 284 257 220 195 157 134

1 1/4 1390 957 768 657 583 528 452 400 322 275

1 1/2 2090 1430 1150 985 873 791 677 600 482 412

2 4020 2760 2220 1900 1680 1520 1300 1160 928 794

3 11300 7780 6250 5350 4740 4290 3670 3260 2610 2240

4 23100 15900 12700 10900 9660 8760 7490 6640 5330 4560

Table 21 - Natural Gas Delivery Capacity - Refer to ANSI Z223.1 - National Fuel Gas Code, Latest Edition

10 20 30 40 50 60 80 100 150 200

Length of Pipe (Feet)

BTU’s Per

Hour x 1,000

Schedule 40

Metallic Pipe

(0.60 Specic

Gravity,

0.5 WC

Pressure Drop)

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 34

UNION

SEDIMENT TRAP

MANUAL SHUT OFF

BALL VALVE

Offset Screw

3. LP (Liquid Propane) Gas Pipe Sizing

Contact gas supplier to size pipes, tanks, and 100% lockup gas pressure regulator. Adjust propane supply regulator provided by the gas supplier for 14 inches w.c. maximum pressure.

B. Gas Connection Requirements

1. The gas connection tting on the water heater is ¾” NPT. NOTE: The pipe size must not be less than ¾”.

2. The supply line must be sized for the maximum output of the water heater being installed. If there are additional gas appliances from the main supply line, measure the size of the supply line according to the COMBINED total maximum BTUH draw for the appliances as if they were operating at the same time.

3. Measure the length of the gas supply line from the gas meter to the water heater. Water heater must be installed downstream of the gas meter to ensure adequate gas supply. Use the tables in this manual or refer to the gas line manufacturer’s sizing information to determine the correct supply pipe size.

4. The National Fuel Gas Code (NFPA 54) requires that a sediment trap (drip leg) be installed in the gas line on appliances not so equipped. The drip leg must be accessible, a minimum of 3” in length, and not subject to freezing conditions. See Figure 40.

5. A manual gas shut-o valve should be installed in the gas supply line close to the water heater. See Figure 40 for detail.

D. Checking Gas Pressure at the Water Heater for Proper Operation

NOTE: Refer to Figure 42 when checking gas pressure. Loosen the

bolts before checking the gas inlet pressure.

1. The water heater and its individual shuto valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures greater than ½ psi (3.5 kPa).

2. The water heater must be isolated from the gas supply piping system by closing its individual manual shuto valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa). The minimum and maximum inlet gas line pressures must meet the requirements shown in Table 19.

Natural or LP Gas

Minimum Pressure 3.5” WC

Maximum Pressure 14”WC

Table 23 - Gas Pressure Requirements

Do not re (operate) the water heater until all connections have been completed and the heat exchanger is lled with water. Doing so will damage the water heater and void the warranty.

Figure 33 - Gas Line with Shut-O and Sediment Trap Detail

6. To facilitate any future maintenance, it is also recommended that an approved gas union tting be installed in the supply line between the shut-o valve and the ¾” NPT connection on the water heater.

7. Use a manometer to test the gas pressure to make sure it meets the minimum standards and does not exceed the maximum standards of the water heater.

8. Leak test the gas line pipe before placing the water heater in operation. Only use approved leak detector liquid solutions to check for leaks.

9. Do not operate the water heater until all connections have been completed and the heat exchanger is lled with water.

C. Additional Precaution for Excess Flow Valve (EFV)

If an excess ow valve (EFV) is in the gas line, check the manufacturer’s minimum and maximum ow capacity ratings. An improperly sized EFV will not allow for a full ow of gas to the water heater and will cause the water heater to malfunction. See Figure 41.

Figure 34 - Excess Flow Valve (EFV)

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Figure 35 - Gas Valve Detail

E. Setting and Verifying the Combustion Setting

1. After the water heater has red, ip DIP switch seven (7) to the ON position (low re). Proceed to check heater combustion values. NOTE: Use a combustion analyzer to ensure CO and CO2 values are within the range shown in Table 20.

It is required to use a combustion analyzer to verify nal adjustment according to the combustion chart (Table 20). Failure to do so could result in serious personal injury or death.

If the readings obtained are lower or higher than the combustion readings in Table 20, use a T15 Torx screwdriver to adjust the oset screw in a clockwise (positive) or counterclockwise (negative) direction (approximately 1/4 turn). See Figure 42. Check your combustion values. Repeat this procedure until the values obtained on the combustion analyzer agree with those stated in Table 20. NOTE: If the heater makes a whistling sound (harmonics) at low re, adjust the oset screw in a clockwise (positive) direction (approximately 1/8 turn). Check your combustion values and ensure they agree with those stated in Table 20 before proceeding.

Page 35

2. When low re settings have been obtained, ip DIP switch seven (7) to its original (OFF) position. This will return the heater to normal operation.

3. Flip DIP switch six (6) to ON (high re). Again check combustion readings with a combustion analyzer. NOTE: DO NOT adjust the gas valve oset screw at high re. The oset screw is only used to adjust combustion values at low re.

4. When complete, ip DIP switch six (6) to its original (OFF) position. This will return the heater to normal operation.

5. Allow heater to operate normally. Ensure it is operating properly.

6. Reinstall the heater front cover.

7. Use a Phillips Head screwdriver to reinstall the heater top cover.

It is very important that the combustion system be set within the recommended CO measurements listed in Table 20. Visually looking at the burner does not determine combustion quality. Failure to measure combustion with a Combustion Analyzer and set the throttle within the recommended CO measurements could result in property damage, severe personal injury, or death.

Natural Gas LP Gas

Fan Speed Low High Low High

CO PPM <175 <175

CO2 (%) 8 - 9 1/2 8 1/2 - 10 9 - 10 1/2 9 1/2 - 11

Table 24 - Combustion Settings

Part 9 - Controls

A. Control and Display Overviews

Hold this Button More than 5 Seconds

When Control Panel Power is ON Status Display Mode When Control Panel Power is OFF Installer Mode

Press this Button Less than 5 Seconds

Turns Control Power Panel ON/OFF

Press this Button Less than 5 Seconds

Select Menu by Pressing Dial Buon Scroll Values by Turning Dial Clockwise(+) or Counterclockwise(-)

Figure 36 - Control Panel Detail

Building Management – 0-10V Input:

Allows the Water Heater to be controlled by

a Building Management System (BMS) NOTE: Icon will only appear if 0-10 Volt is connected.

Current Time

Current Day of Week

Appliance is Meeting DHW Demand

Anti-Freeze Mode

is Operational

Press this Button Less than 5 Seconds

Access and Change DHW Set-Point Temperature

95 – 140

F (37.8 – 49oC)

NOTE: If Installer Mode Parameter 25:rE is

changed to Co, Set-Point Temperature can be

changed to 160oF

Hold this Button More than 5 Seconds Change Current Time Seng Year/Month/Date/Hour/Minute/Day of Week

Status Display Mode or

Installer Mode is Operational

Service Reminder

Appliance is in a

Communication State

Flame On

Fan On

System Pump On

Displayed Number Indicates Cascaded Unit

Cascade Status

Full On Rectangular Icon Under Number Indicates Unit is Running

Flashing Rectangular Icon Under Number Indicates Unit Error

Figure 37 - LCD Display

Eight (8) Segment Display with

Colon and Decimals Displays

Numerals and Characters

Heater Pump On

Celsius and

Fahrenheit Indicators

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 36

The LCD display also features a backlit lamp that will illuminate:

• When a user action is detected (a button is pressed)

• The display has timed out for approximately 2 minutes

B. Start-Up Sequence

After the appliance is powered ON, the LCD display shows a sequence of information. The icons will ash, followed by various indicators that describe the appliance controller and software versions. It will take the appliance roughly 15 seconds to cycle through the Start-Up Sequence.

Display Items Time for Display Remarks

LCD Test

Category: CGH-199

Software Version for

Front Panel

Software Version for

Water Heater

Hardware Version for

Water Heater

Table 25 - Start-Up Sequence

After start-up, the display appears as follows.

1 sec All segments “ON”

0.5 sec All segments “OFF”

1 sec Pdn

1 sec 0061

1 sec SPn

1 sec 00.xx

1 sec SFn

1 sec xx.xx

1 sec Hdn

1 sec 00xx

Factory DHW Set-Point is 120oF (48.8oC). Initial DHW Set-Point range is 95 – 140oF (35 – 60oC).

Turn the dial counterclockwise to lower and clockwise to raise the DHW set-point. After changing the temperature, press the

button to save the set-point. To change the DHW Set-Point above 140oF (60oC), go into the Installer Mode. Advance to parameter 25:rE and change the setting

from rE to Co. Then leave Installer Mode. Press the button. The current DHW set-point will display. The temperature range is now 95 – 160oF (35 – 71.1oC).

Turn the dial counterclockwise to lower and clockwise to raise the DHW set-point. After changing the temperature, press the

button to save the set-point. NOTE: After a DHW demand has been met, the post pump run time (default: 1 minute) will run to normalize heat exchanger temperature and prevent scale build-up. NOTE: The water heater temperature will be 20oF higher than the Storage Tank Temperature Setting UNLESS the Water Heater Oset Temperature Setting (13:ST) is changed. For example: If DHW setpoint is 130oF, the standard Water Heater Oset Temperature Setting of 20oF will equal a minimum water heater temperature of 150oF.

Hotter water increases the risk of scald injury. Scalding may occur within 5 seconds at a setting of 140oF (60oC). Water temperature over 125oF can instantly cause severe burns, or death, from scalds. Children, disabled, and elderly are at the highest risk of being scalded. See instruction manual before setting temperature at appliance. Feel water before bathing or showering!

Figure 38 - Initial Display Screen

The Control System can operate through user and service modes that have specic LCD outputs and dedicated controls, including:

• Changing the DHW Set-Point Temperature

• Changing Time

• Status Display

• Installer Mode

• Error Mode

C. Changing the DHW Set-Point

The display shows the icon when the DHW set-point can be changed.

D. Changing the Time

Press and hold the button for ve seconds when the display panel is powered ON to change the time. The settings can be adjusted as follows: Year / Month / Date / Hour / Minute / Day of Week.

Figure 40 - Changing the Time Screen

Turn the dial counterclockwise to lower and clockwise to raise the current time setting. After changing the setting, press the

button to save it. The next adjustable setting will appear. After the

time and date have been set, press the button to save and return to the main screen.

Figure 39 - DHW Set-Point Screen

Press the button when the display panel is powered ON to change the DHW Set-Point. The DHW icon and current set-point will display and ash. This indicates that the DHW Set-Point can be changed.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 37

E. Status Display

Status Display will activate when button is pressed and held for ve seconds at Standby Mode when the display panel is powered ON.

Figure 41 - Status Display Screen

Display

(Main Menu)

L:rt

M:CC

Table 26 - Status Display Screen Descriptions - NOTE: 0-10V to control storage tank setpoint (10:dH, 1.5V = 95F; 10V = 180F)

(Sub Menu)

A:In

b:tt

C:Rt

d:Fr

E:oP

F:Eh

H:dH

I:oH

N:St

Display

1:PH

2:rh

3:rH

4:It

5:IH

SELF

ALL

F1 - F19

Detail Description

0-10V Display

DHW target temperature Current DHW target temperature

DHW inlet water temperature Current DHW inlet water temperature

Fan speed (RPM) Current fan speed (RPM)

Heat exchanger outlet water temperature Current heat exchanger outlet water temperature

Exhaust temperature Current exhaust temperature

Display: Current DHW tank temperature measured by the indirect

DHW storage tank temperature

* If temperature sensor or mechanical aqua stat

is not connected then it will display OFF

Water Heater Overheat Temperature Current Water Heater Temperature

Power supply

Burner operating time Time burner has operated in 1 hour units

Burner

Operation Time

Capacity of Master (percentage) Percentage of Master Unit Running

Total Cascade Capacity (percentage). This icon

will only be displayed when the units are in

NOTE: This index will only be shown in cascade

Capacity of individual water heaters

(percentage). This icon will only be displayed

when the units are in cascade mode.

Supply Outlet Temperature Current Supply Outlet Temperature (Cascade Mode)

Burner operating time Time burner has operated in 1000 hour units

Ignition attempts

cascade mode.

mode.

Display: OFF – when a mechanical aquastat is connected and the

Display: ON - When a mechanical aquastat is connected and the

L:rt on display on

sub menu

This screen shows the overall cascade power output. The range of this value of water heaters communicating with the Master x 100.

For example, if eight (8) water heaters are connected and

communicating, the maximum cascade power is 800%.

Current Voltage of 0-10V Input

(When --- is displayed, 0-10V is not connected.)

tank sensor (7250P-325)

contact is open, or no sensor is connected.

contact is shorted.

Time water heater has been powered in 1000

hour units

Number of ignition attempts: 10 times the

displayed unit

Number of ignition attempts: 10,000 times

the displayed unit

Percentage of cascade units running.

Range: 0-100%

Percentage of each cascade units running.

Ex. M, F1, F2, ….

Turn the dial counterclockwise and clockwise to scroll through the displayed parameters. To view parameter details, press the

button at the appropriate screen. Press the or buttons to leave the parameter.

Press the button again to return to Operation Mode.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 38

F. Installer Mode

Installer Mode will activate when button is pressed and held for ve seconds while the water heater display is powered O.

Figure 42 - Installer Mode Screens

Display Default Detail Description

1:EH E0.00

2:cE OFF

3:In OFF

4:FH 00

5:FL 00

6:dr NO

7:dl NO

8:bo 7F

9:db 100

10:dH 120F

11:dd 7F

12:Pr 1 MIN

13:ST 20F

14:FP ON

15:cn 0

16:cP 1

17:cI 1

18:Eh OFF

Cr:at Auto

19:Cr

Cr:Ct 48

Error history up to 10 Check ten most recent Error Codes (E0 - E9)

Clear Error History Select “ON” to Clear Error History. Range: ON or OFF

System Reset

(Factory Setting)

Maximum Fan Speed Adjusts maximum fan speed. Range: -30 to +30

Minimum Fan Speed Adjusts minimum fan speed. Range: -30 to +30

Reset Burner Operation Time

Reset Ignition Cycle

Set Dierential Temperature to

Turn Burner “ON”

DHW capacity

Storage Tank Temperature Set

Point

Storage Tank Dierential Set

Point

System and Heater Pump Post

Run Time

Water Heater Oset

Temperature

System Freeze Protection Mode

Cascade Address

Cascade Parameter

Minimum Operating Number

for Cascade Units

Factory Setting Factory Setting - DO NOT CHANGE

Automatic Rotation

(default)

Cascade Rotation Time

(Burner operation time, Ignition cycles, and Supply power time will not be reset. See

When set, the appliance will operate to heat water when water temperature falls

Example: If set point is 160oF and dierential is 7oF, the appliance will turn on

when water temperature falls below 153oF. NOTE: The dierential temperature

Outlet temperature dierential above tank set point. This is the amount of degrees

above the tank setpoint that the water heater will maintain its outlet water

System Freeze Protection Mode. This mode should be turned OFF for snow melt

NOTE: “16:cP” needs to be set with total number of units in the cascade parameter

before setting “15: cn” NOTE: The Master water heater must always be addressed 0.

Selects how many cascaded units will operate simultaneously when a DHW demand

The rst unit to operate when there is a DHW call is the unit that ran the least

NOTE: If unit is set to run continuously, this parameter must be set, NOT Automatic

Select “ON” to restore system to default factory settings

Functions 8 and 9.)

Range: ON or OFF

Select “YES” to Reset Burner Operation Time

Range: YES or NO

Select “YES” to Reset Ignition Cycles

Range: YES or NO

below a dierential setting.

must be equal to or below the Storage Tank Dierential Setpoint (11:dd).

Range: 5oF – 11:dd(Storage tank dierential setpoint)

Set DHW combustion rate

Range: 50 - 100%

Sets Maximum Storage Tank Temperature

Range: rE: 95 - 140oF or Co: 95 - 160oF

Storage Tank Dierential Set Point

Range: 5 - 30oF

System and Heater Pump Post Run Time

Range: 0 - 10 Min

temperature while there is a demand for heat.

Range: 5 – 40oF

application. NOTE: This mode should be ON during normal operation.

Range: ON or OFF

Cascade Address

Range: 0 (Master), 1 (follower 1), …., 20 (follower 19). Default: 0.

Number of Units Cascaded

Range: 01 - 20

is initially received.

Range: From 1 to Total Number of Units Cascaded

amount of time during the prior heat calls (burner ON time).

Cascade Rotation Time

Rotation (Cr:at) to ensure even unit run time. Range: 0 - 240 Hours

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 39

Display Default Detail Description

This water heater may be installed at elevations up to 10,000 feet and operate on either Natural or LP. The appliance will de-rate by 4% for each 1000 feet above sea level. Select the appropriate installation location as described below.

20:HA 0-2

AP:cP 5

21:AP

cP:oFF

cP:on

22:SS

SS:Sd

OFF

YEAR

MON

High Elevation Mode

System Pump and Heater

Pump Test Mode

System Pump and Heater

Pump Test Mode

OFF

Service Reminder Date

Selects Installation Location for Proper Water Heater Operation at Altitude:

NOTE: Use a calibrated combustion analyzer to ensure CO and CO2 are within the ranges shown in this manual. Adjust the oset screw in the clockwise (positive) or counterclockwise (negative) directions (approximately 1/8 turn) if the measured CO2 value on LOW FIRE is out of range.

This function sets the time to run the system pump or heater pump to purge air

Sets the date of the next service reminder: XX/XX/XXXX (MONTH/DAY/YEAR).

0-2 for installation locations from sea level to 1999 feet

2-5 for locations from 2000 to 4999 feet 5-8 for locations from 5000 to 7999 feet,

8-10 for locations from 8000 to 10000 feet

from the system. Range: 1 – 30 minutes

Turn this function on to activate system pump and heater pump. Only works in installation mode. Turns o when in normal mode.

NOTE: A wrench will appear on the display panel when service is due.

DAT E

SS:br 00

23:UC

24:SA

25:rE

Table 27 - Installer Mode Descriptions

FAH (F)

CEL (C)

AquA

SEnS

FAH(F)

AquA

Turn the dial counterclockwise and clockwise to scroll through the displayed parameters. To view parameter details, press the

button at the appropriate screen. Turn the dial counterclockwise and clockwise to change the selected parameter. To save the setting

press the button.

To leave Installer Mode, press the button again. The display will return to power o mode.

G. Setting Up a Cascaded System

Service Reminder Run Hours Sets the next service reminder based on burner run hours. (OFF, 0 - 9000 hours)

Temperature Measurement

Unit

Select AquA or SEnS

Select rE or Co

Allows the user to change the temperature measurement unit from Fahrenheit to

Select DHW Sensor Type

Range: AquA (Aquastat) or SEnS (Sensor)

Changes DHW Setpoint Temperature Range

rE (95 - 140oF [35 - 60oC]) or Co (95 - 160oF [35 - 71.1oC])

There are three modes of operation available in Cascaded Systems:

1. Standard Conguration - Refers to a Cascaded System where

the Master water heater controls Follower water heaters to meet the system setpoint. This set up requires either a) a system pump, or b) individual pumps for each cascaded unit. A system pump would be wired into the Cascade Master only. Individual pumps are wired into the individual heater pump line voltage terminal connections. There is either a DHW sensor or aquastat installed in the storage tank. This sensor is wired into the low voltage terminal strip of the Cascade Master. Each water heater requires cascade wiring.

2. Continuous Operation - Refers to a Retro-Fit Cascaded A maximum of sixteen (16) models may be installed in a cascaded system. Installing more than the maximum amount of water heaters in a cascaded system will result in system problems, property damage, and premature water heater failure. Such problems ARE NOT covered by product warranty.

System where there is no control location on the storage tank and the pump runs continously. The Master water heater controls Follower water heaters to meet the system setpoint temperature. This set up requires a system pump. This pump must be wired to line voltage for continuous operation. DO NOT wire the system pump to the water heater. A system pipe

sensor is required, and must be installed on the return piping For each oor containing bedroom(s), a carbon monoxide detector and alarm shall be placed in the living area outside the bedrooms, as well as in the mechanical room that houses the heater. Detectors and alarms shall comply with NFPA 720 (latest edition). Failure to comply with these requirements could result in product damage, severe personal injury, or death.

near the storage tank. Each water heater requires cascade

wiring.

3. Building Automation System - These water heaters are equipped with a 0-10V DC input to control the operating temperature of the cascaded system and storage tank. Once voltage of 1.5V or greater is applied the Cascaded System will begin maintaining the temperature based on the input voltage and its respected temperature as listed in Table 33. Note that the cascaded system will turn o when the voltage is less than 1.5V.

When setting up a cascade system, each individual water heater control must be programmed for cascade operation.

Default: 0 – 2

Celsius.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 40

This is the Cascade Master display screen. It is operating. This is the Cascade Follower 1 display screen. It is operating.

This is the Cascade Follower 2 display screen. It shows an Error Code. This is the Cascade Follower 3 display screen. It is in standby mode.

CAUTION

Program the Master and Follower Water Heaters in a Cascade System:

To program the cascade system, rst enter the Installer Mode. Scroll down to and select the following parameters on each water heater in the system:

1. 16:cP – Set the number of units in the cascade loop [range from 1-20].

2. 15:cn – Next, set the cascade address (Master should always be addressed 0) [range from 0-19]. 15:cn cannot be changed until 16:cP is set.

NOTE: The cascade Master must be addressed 0. Followers may be given any address from 1 - 19, but addresses should NEVER be repeated. NOTE: To service any follower unit, turn main power switch o to that unit. Program the Master Water Heater Setpoint:

To nish programming the cascade system, enter the Installer Mode on the Master ONLY.

1. Set the DHW setpoint on the Master to match the storage tank setpoint temperature. This DHW setpoint will be the same on all of the Followers.

2. Set the Water Heater Oset Temperature on the Master (13:ST). (Range: 5-40oF, Default: 20oF).

Figure 43 - Cascade Display Screen Examples

H. 0-10 Volt Input

1. A signal from a building management system may be connected to the water heater to enable remote control. This signal should be a 0-10 volt positive-going DC signal. When the 0-10V input is wired to the water heater terminal strip, a building control system can be used to control the set point temperature of the water heater. The control interprets the 0-10 volt signal as follows; when the signal is between 0 and 1.5 volts, the water heater will be in standby mode, not ring. When the signal rises above 1.5 volts, the water heater will ignite. As the signal continues to rise towards its maximum of 10 volts, the water heater will increase in set point temperature.

2. Connect a building management system or other auxiliary control signal to the terminals marked for this purpose on the water heater terminal block (shown in Piping Diagrams, this manual). Caution should be used to ensure that the 0-10 VOLT + connection does not become connected to ground. NOTE: Ensure that the polarity of the connections from the external modulating water heater controller to the water heater is correct. Reversed polarity could lead to erratic and/or no response from the water heater controller.

NOTE: Outdoor Temperature Mode Icon on the display will ash if an Outdoor Sensor or 0-10 Volt is not connected to the water heater.

0-10 V INPUT TABLE:

When outside voltage is applied to the connector (2) in the wiring diagram,

1. The 0-10V symbol is displayed.

2. The heating temperature is automatically set according to the external voltage input. NOTE: 0-10V is prioritized over Aquastat/Sensor. If input voltage is less than 1.5V then Aquastat/Sensor will operate.

The range of input voltage is approximately 1.5[V] ~ 10[V] and the heating temperature settings according to this range are as follows.

Input voltage[V] Heat temperature [oC] Heat temperature [oF]

1.5 35.0 95

2.0 37.1 98.8

2.5 39.2 102.7

3.0 41.3 106.5

…

Table 28 - 0-10V Input Voltages and Associated Temperatures

9.0 66.6 152

9.5 69 156.2

10 71.1 160

Voltage exceeding 15V may damage internal parts. Such damages are not covered by product warranty.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 41

Part 10 - Troubleshooting

A. Error Code

When the water heater encounters an error, the display will ash “Er” followed by a numerical code. The water heater shall enter a soft lockout condition if the error is such that it can return to normal operation once the condition relieves itself (overheat conditions, NTC open or shorts, etc.). The water heater shall enter a hard lockout if the condition indicates something more serious (ame, ignition, condensate line, etc.) To clear a hard lockout Error Code, press the Power button. See Figure 51. The following screen will display when the water heater encounters an error.

Figure 44 - Error Screen

Error Code Error Code Description Possible Remedies

Press the Power button to clear the Error Code. The Code will also automatically reset after one hour (up to three (3) times. If Error happens again:

1. Monitor the gas pressure to the water heater while in operation. Ensure pressure is between 3.5 and 14”

Er:10

Er:11

Er:16

Er:20

Er:25

Flame has extinguished 5

(ve) times

Ignition has failed 5 (ve)

times

Operating Temperature

Sensor Detects Water

Temperature Greater than

199oF (93oC)

Condensate - Closed is

Normal, Open is Fault

(Condensate Drain Trap

Pump operation fault

NOTE: This error occurs if

there is no ow through

the unit while ring. This is

detected when the dierence

between OP and Outlet (St)

temperature is more than 20F.

WC.

2. Check gas valve wire. Ensure connection is secure.

3. Check ame detection sensor. Ensure connections are secure. Normal operating settings are more than

2.5DC before ignition, less than 2.5DC after ignition.

4. Check vent terminations. Ensure there are no blockages.

5. Assure that the ame is stable when lit.

6. If the problem persists, replace the main control.

Press the Power button to clear the Error Code. The Code will also automatically reset after one hour (up to three (3) times. If Error happens again:

1. Monitor the gas pressure to the water heater while in operation. Ensure pressure is between 3.5 and 14” WC.

2. Check gas valve wire. Ensure connection is secure.

3. Check ame detection sensor. Ensure connections are secure. Normal operating settings are more than

2.5DC before ignition, less than 2.5DC after ignition.

4. Check igniter transformer for proper connection.

5. Clean the spark igniter with steel wool to remove oxides. Ensure proper separation (3-4 mm).

6. Replace the spark igniter if damaged.

7. Assure that the ame is stable when lit.

8. If the problem persists, replace the main control.

This Error Code will go away when the DHW temperature decreases. If Error happens again:

1. Check if dip switch High Fire setting is ON. Switches 6 and 7 should be OFF for normal operation.

2. Check if DHW inlet pipe is blocked. Ensure there is enough water owing to the water heater.

3. Check DHW sensor at DHW outlet. If resistance is zero, replace the sensor.

4. Check Operating Temperature sensor at the heat exchanger. If resistance is zero, replace the sensor.

5. If the problem persists, replace the main control.

Press the Power button to clear the Error Code.

1. Check Condensate and main controller connections. Ensure all are secure.

2. Check Condensate resistance. If resistance is not zero, replace the switch.

3. Check Condensate hose. Ensure it is connected and in good condition.

4. Check condensate line and termination for blockages.

5. Check exhaust vent for blockages.

6. If the problem persists, replace the main control.

This Error Code will go away when the dierence between OP temperature and Outlet temperature is less than 10F. If Error happens again:

1. Ensure the pump is connected properly and operational. Replace pump if it is not operational.

2. Check Op and Outlet temperature sensors resistance. If resistance is zero, replace the sensor (s).

3. If the problem persists, replace the main control.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 42

Error Code Error Code Description Possible Remedies

Press the Power button to clear the Error Code. If Error happens again:

1. Ensure the pump is connected properly and operational. Replace pump if it is not operational.

2. Check Outlet temperature sensor. Ensure connections are secure.

3. Check Outlet sensor resistance. If resistance is zero, replace the sensor.

4. If the problem persists, replace the main control.

This Error Code will go away when temperature decreases. If Error happens again:

1. Check overheat temperature sensor. Ensure connections are secure.

2. Check overheat sensor resistance. If resistance is zero, replace the sensor.

3. If the problem persists, replace the main control.

Press the Power button to clear the Error Code.

1. Check APS and main controller connections. Ensure all are secure.

2. Check APS resistance. If resistance is not zero, replace the switch.

3. Check APS hose. Ensure it is connected and in good condition.

4. Check condensate line and termination for blockages.

5. Check exhaust vent for blockages.

6. If the problem persists, replace the main control.

This Error Code will go away when outlet water temperature decreases. If Error happens again:

1. Ensure the pump is connected properly and operational. Replace pump if it is not operational.

2. Check outlet temperature sensor. Ensure connections are secure.

3. Check outlet sensor resistance. If resistance is zero, replace the sensor.

4. If the problem persists, replace the main control.

NOTE: This error will only appear if an aquastat is installed and SEnS is selected in Installer Mode 39, or a sensor is used and it is shorted. This Error Code will go away if an aquastat is installed, AquA is selected in Installer Mode 39, and the water heater is powered OFF and ON, or the DHW sensor is repaired or replaced.

1. Check DHW sensor. If an aquastat, ensure AquA is selected in Installer Mode 39. If a sensor, ensure connections are secure.

2. Check DHW sensor resistance. If resistance is zero or does not match that in Table 38, replace the sensor.

3. After completing steps 1 and 2, power the water heater OFF. Then turn it back ON.

4. If the problem persists, replace the main control.

This Error Code will go away when outlet water temperature decreases. If Error happens again:

1. Check operating temperature sensor. Ensure connections are secure.

2. Check sensor resistance. If resistance is zero, replace the sensor.

3. If the problem persists, replace the main control.

This Error Code will go away when exhaust temperature decreases. If Error happens again:

1. Check exhaust temperature sensor. Ensure connections are secure.

2. Check sensor resistance. If resistance is zero, replace the sensor.

3. Check exhaust vent for blockage.

4. If the problem persists, replace the main control.

Supply voltage is too low to operate. This Error Code will go away when supply voltage returns to normal operating range. If Error happens again:

1. Ensure water heater is properly wired to a power source meeting the requirements on the rating plate.

2. If problem persists, replace the main control.

Supply frequency is too high to operate. This Error Code will go away when supply frequency returns to normal operating range. If Error happens again:

1. Ensure water heater is properly wired to a power source meeting the requirements on the rating plate.

2. If problem persists, replace the main control.

Press the Power button to clear the Error Code. Replace the main control.

The Error Code will go away unless it occurs ve (5) times in ten (10) minutes. Press the Power button to clear the Error Code. If Error happens again:

1. Check the vent connections for blockages.

2. Check the burner assembly.

3. Check fan operation. If fan appears to be operating normally but RPMs are too low or too high, replace the fan.

4. If the problem persists, replace the main control.

Er:26

Er:28

Er:29

Er:30

Er:32

Er:33

Er:35

Er:36

Er:37

Er:38

Er:41

Outlet Water Temperature (OP) Sensor Detects Water

Temperature Greater Than

219oF (104oC)

Overheat Sensor (OH) Open

or Short

APS - Closed is Normal, Open

is Fault

Outlet Temperature Sensor

(ST) Fault

DHW Sensor (dH) Short

H/X Temperature Sensor (OP)

Open or Short

Exhaust Sensor (Eh) Open or

Short

Abnormal Supply Voltage

Abnormal Supply Frequency

Error Appears When Control

Stores Data, but Data is not

Saved

Fan Speed too high with

ame on

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 43

Press the Power button to clear the Error Code.

Er:42

Er:43

Er:61

Er:70

Er:72

Er:76

Er:80

Er:81

Er:85

Er:94

Table 29 - Error Codes and Suggested Corrective Actions

Low Water Cut-O circuit is

open

Burner overheat switch open

Fan Speed Feedback Signal

Abnormal

AD Abnormal, Important

EPROM Data or Safe Data

Abnormal

Flame Signal Detected before

Ignition

Poor Communication

Low Water Level Sensor

(Low Water Level Detected

four [4] Consecutive Times)

Low Water Level Circuit

Freeze Protection

(Water heater has detected

[OP] water temperature below

34oF [1oC])

Exhaust NTC (Eh) detects Vent

Temperature is Greater than

190oF (88oC)

If Error happens again:

1. Ensure that the LWCO jumper is installed if low water cut o is not use.

2. Ensure that the water LWCO wires are properly installed (if in use).

3. Ensure that the LWCO ground wire is properly grounded.

4. If the problem persists, replace the main control.

Press the Power button to clear the Error Code. If Error happens again:

1. Check burner overheat switch connections. Ensure connections are secure.

2. Check switch resistance. If resistance is not zero, replace the switch.

3. If the problem persists, replace the main control.

This Error Code will go away when the condition is remedied. If Error happens again:

1. Check the connections to the fan. Ensure all are secure.

2. If the fan does not rotate during the ignition sequence, check for 8Vac 26.5Vac power at the fan connection. If 8Vac 26.5Vac power is present at the control, replace the fan. If the blower does not have 8Vac

26.5Vac power, check power at the control. If 8Vac 26.5Vac power is not present at the control, replace the control.

3. If the problem persists, replace the main control.

This Error Code will go away when the condition is remedied. If Error happens again:

1. Turn power OFF and ON at the main power switch internal to the water heater.

2. If the problem persists, replace the main control.

This Error Code will go away when the condition is remedied. If Error happens again:

1. Check the water heater cover. Ensure it is secure. Flame detection sensor can detect an external light source.

2. Check ame detection sensor. Ensure connections are secure. Normal operating settings are more than

2.5DC before ignition, less than 2.5DC after ignition.

3. If the problem persists, replace the main control.

This Error Code will go away when the condition is remedied. If Error happens again:

1. Check connections from main control to display panel.

2. If the problem persists, replace the display and/or the main control.

This Error Code will go away when the condition is remedied. If Error happens again:

1. Ensure all valves are open to the water heater and there are no leaks.

2. Ensure all air has been purged from the system.

3. Check wiring connections to low water level sensor. Ensure all are secure.

4. Check low water level sensor resistance. If resistance is zero, replace the sensor.

5. If the problem persists, replace the main control.

This Error Code will go away when the condition is remedied. If Error happens again:

1. Ensure the system is lled with water. Ensure all valves are open to the water heater and there are no leaks.

2. Check wiring connections to low water level sensor. Ensure all are secure.

3. Check low water level sensor resistance. If resistance is zero, replace the sensor.

4. If the problem persists, replace the main control.

This Error Code will go away when the freezing condition is remedied. If Error happens again:

1. Ensure water heater is located in a mechanical room protected from freezing conditions.

2. Ensure all valves are open to the water heater, there are no leaks.

2. Check wiring connections to low water level sensor. Ensure all are secure.

3. Check low water level sensor resistance. If resistance is zero, replace the sensor.

4. If the problem persists, replace the main control.

This Error Code will go away when the condition is remedied. If Error happens again:

1. Check if dip switch High Fire setting is ON. Switches 6 and 7 should be OFF for normal operation.

2. Check exhaust temperature sensor. Ensure connections are secure.

3. Check sensor resistance. If resistance is zero, replace the sensor.

4. Check exhaust vent for blockage.

5. If the problem persists, replace the control.

6. If the problem persists, replace the heat exchanger.

This water heater is equipped with a blocked vent shuto system. If Error Codes Er:29, Er:41, Er: 42, or Er:94 occur, turn o the gas valve at the manual shuto. Check the vent terminations for obstructions. If no obstructions are found, reset the water heater by pressing the power button. If the error continues to occur, call a qualied service technician or the gas supplier to check the water heater. Failure to follow these instructions could result in property damage, personal injury, or death.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 44

B. Error Tree Analysis

1. Flame Detection

Figure 45 - Flame Detection Error Analysis Tree

2. Air Pressure Switch Detection

Figure 46 - Air Pressure Switch Analysis Tree

3. Inlet / DHW / Operating Temperature / Exhaust Sensors

Figure 47 - Inlet / DHW / Operating Temperature Sensors Error Analysis Tree

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 45

C. Suggested Corrective Actions

Problem Possible Causes Possible Remedies

1. Is the plug on the power supply cord unplugged

No electrical power to the water

heater

No water available when faucet

is opened

Hot water is not available when

a faucet is opened

The water temperature is not hot

enough or turns cold during use

It takes a long time before hot

water ows from the faucet

The water is not hot enough Is the water temperature set too low? Adjust the temperature setting.

The water at the faucet is too hot Is the water temperature set too high? Adjust the temperature setting.

A fan can be heard even when

the unit is not operating

White “smoke” can be seen coming out of the exterior

exhaust gas vent

Table 30 - Troubleshooting Chart

DIAGNOSTICS AND SUGGESTED CORRECTIVE ACTIONS

The water heater control is able to record information about the water heater’s condition at the time of the ten previous faults or errors. This information is available to view in the Installer Mode under the History screen. The following screens may be displayed when reviewing the water heater history. The table below also includes diagnostic information and possible corrective actions.

Display Condition Diagnostic Possible Corrective Actions

Nothing appears on the display but the fan runs at full

speed

Nothing appears

on the display

control panel

and no other water heater

components are

operating

Control is not

receiving power

Control is not

receiving 120V

from the electrical outlet?

2. Is the circuit breaker tripped?

3. Is the fuse on the circuit board good?

4. Is there a power outage to the home?

1. Is the water supply valve shut o at the meter (do cold water faucets work)?

2. Is the water supply valve near the unit open?

3. Is the water pipe frozen?

4. Is an error code ashing on the display panel (leak detected)?

1. Does the water heater have power (plugged in)?

2. Is the water heater turned ON?

3. Is an error code ashing on the display panel?

4. Is the gas supply valve open or shut o at the meter (do other gas devices work)?

1. Is an error code ashing on the display panel?

2. Is the outlet water temperature set too low?

Is the faucet some distance from the water heater?

1. The fan operates after the burner shuts o to clear combustion gases from the exhaust vent.

2. The fan may run to help prevent freezing.

Depending on the outside temperature, water vapor can be produced as the exhaust is vented.

Check for incorrect or short circuited wiring

Check transformer connection to the control per wiring diagram. Check for 14V output of panel wire.

Ensure service switch and/or circuit breaker to water heater is turned ON

Is there 120V at the service switch

Is the ON/OFF switch inside the water heater cabinet is turned on

power

Check for 120V at the line voltage terminal block located inside the water heater cabinet

Inspect the fuse. Replace as necessary

1. Reset the plug.

2. Reset the circuit breaker.

3. If the display panel is blank, unplug the unit or contact an authorized service technician.

4. Contact the power company.

1. Open the closed supply valve.

2. Open the water supply valve.

3. Turn OFF the unit, close all water valves and the gas valve. Contact an authorized service technician.

4. Refer to error code information and contact an authorized service technician.

1. Restore electrical power to the unit.

2. Press and hold the Power button to turn the unit ON.

3. Refer to the Diagnostic and Error Codes section in this manual.

4. Open the gas supply valve.

1. Open the faucet to allow more water ow.

2. Refer to the Diagnostic and Error Codes section in this manual.

3. Adjust the outlet water temperature (refer to the procedure in this manual).

1. Install a recirculation line.

2. Allow time for the cold water already in the pipes to ow from the faucet.

1. This is normal operation – no action is required.

2. Protect the water heater from freezing temperatures or shut o and drain the unit.

This is normal operation – no action is required.

Correct wiring per wiring diagram including connection of transformer to the control.

Push the Power button on the control panel

Turn on service switch or circuit breaker to power water heater

Troubleshoot and correct the power supply to the manual switch

Turn ON the manual power switch inside the water heater cabinet

Correct wiring inside the heater cabinet using the wiring diagram in the installation manual

Replace the fuse. See replacement parts section for part number. If fuse blows again, recheck the wiring per diagram.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 46

Display Condition Diagnostic Possible Corrective Actions

Nothing appears

on the display

control panel, but

the water heater is

operating

Display repeatedly

cycles initialization

sequence

Table 31 - Diagnostics and Suggested Corrective Actions

Occurs when

communication is

lost from the control

to the display

Occurs when control

does not receive

signal from fan

Check for loose connections and proper pin alignment / engagement on the control’s plug

Cycle power o and on using water heater power switch and check for operation

Cycle power o and on using appliance power switch and check for operation

Check for continuity on the wire harness from the display to the control. See repair parts section for proper replacement part.

Replace with new display module. See replacement parts section for part number.

Replace fan

Part 11 - Start-Up

Clean system to remove sediment*

Thoroughly clean and ush any system before installing the water heater.

A. Check / Control Water Chemistry

If you suspect that your water is contaminated in any way, discontinue use of the appliance and contact an authorized technician or licensed professional.

Contaminant Maximum Allowable Level

Total Hardness

(Commercial Use - Above 140oF

water temperature)

Aluminum 0.05 to 0.2 mg/l or PPM

Chloride 100 mg/l or PPM

Copper 1 mg/l or PPM

Iron 0.3 mg/l or PPM

Manganese 0.05 mg/l or PPM

pH 6.5 - 8.5

Sulfate 205 mg/l or PPM

Total Dissolved Solids (TDS) 500 mg/l or PPM

Zinc 5 mg/l or PPM

Dissolved Carbon Dioxide (CO2) 15 mg/l or PPM

Table 32 - Water Quality Specications

*NOTE: It is recommended to clean the heat exchanger at least once

a year to prevent lime scale buildup. To clean the heat exchanger, follow the maintenance procedure in this manual.

120 mg/l

(7 grains/gallon)

1. You must thoroughly ush the system (without water heater connected) to remove sediment. The high-eciency heat exchanger can be damaged by buildup or corrosion due to sediment.

2. Flush system until water runs clean and you are sure piping is free of sediment.

NOTE: Water heater failure due to improper water chemistry is not covered by warranty.

B. Check for Gas Leaks

Before starting the water heater, and during initial operation, smell near the oor and around the water heater for gas odorant or any unusual odor. Remove water heater front door and smell interior of water heater enclosure. Do not proceed with startup if there is any indication of a gas leak. Repair any leaks at once.

PROPANE WATER HEATERS ONLY – The propane supplier mixes an odorant with the propane to make its presence detectable. In some instances the odorant can fade, and the gas may no longer have an odor. Before startup (and periodically thereafter), have the propane supplier verify the correct odorant level in the gas.

If you discover any evidence of a gas leak, shut down the water heater at once. Find the leak source with a bubble test and repair immediately. Do not start the water heater again until the leak is repaired. Failure to comply could result in substantial property damage, severe personal injury, or death.

C. Fill and Test Water System

• Ensure any drain valves are completely closed.

• Open the shut-o valve in the cold water supply line.

• Open the hot water faucets to allow air to vent from the heater and piping.

• Allow sucient time for the heater to completely ll with water.

D. Condensate Removal

1. The water heater is a high eciency condensing water heater. Therefore, the unit has a condensate drain. Condensate uid is nothing more than water vapor, derived from combustion products, similar to that produced by an automobile when it is initially started.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 47

Visual Check Hole

Ensure Flame is Blue

Condensation is slightly acidic (typically with a pH of 3 to 5) and must be piped with the correct materials. Never pipe the condensate using steel, copper, brass or other materials that will be subject to corrosion. Plastic PVC or CPVC pipe are the only approved materials. A condensate neutralizer, if required by local authorities, can be made up of lime crystals, marble or phosphate chips that will neutralize the condensate. This may be done by the installer or you may purchase a condensate neutralizer from HTP (7450P-212).

2. The water heater is equipped with a ¾ female socket weld tting connection that must be piped to a local drain. It is very important that the condensate line is sloped downward away from the water heater to a suitable inside drain. If the condensate outlet on the appliance is lower than the drain, you must use a condensate removal pump, available from HTP (554200). This pump is equipped with two leads that can be connected to an alarm or another type of warning device to alert the user of a condensate overow, which, if not corrected, could cause property damage.

3. If a long horizontal run is used, it may be necessary to create a vent in the horizontal run to prevent a vacuum lock in the condensate line.

4. Do not expose the condensate to freezing temperatures.

5. It is very important you support the condensation line to assure proper drainage.

DHW Inlet (Rt) / Outlet Temperature

(St) Sensor

(7850P-015)

Exhaust Temperature (Eh) Sensor

(7850P-070)

Temperature (oF) Resistance (Ω) Temperature (oF) Resistance (Ω)

-4 62162 -4 28409

5 48440 5 22152

14 38045 14 17408

23 30107 23 13782

32 23998 32 10990

41 19261 41 8824

50 15562 50 7131

59 12655 59 5800

68 10353 68 4747

77 8520 77 3906

86 7051 86 3233

95 5867 95 2690

104 4908 104 2250

113 4125 113 1891

122 3485 122 1598

131 2957 131 1356

140 2520 140 1155

149 2157 149 989

158 1854 158 850

167 1600 167 733

176 1386 176 635

185 1205 185 552

194 1051 194 482

203 920 203 421

212 808 212 370

Table 33 - Temperature Sensor Resistance

HX (OP) Temperature Sensor

(7850P-081)

Figure 48 - Flame Sight Glass

Part 11 - Installation Checklist

Before Installing Yes No

Is there enough space to ensure proper installation?

Does installation location allow for proper service clearances?

Are water and gas lines properly sized and set at proper pressures for the installation?

Have combustible materials been cleared from the installation location?

Is there a drain close to the water heater?

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 48

Water Piping Yes No

Does water heater loop piping meet the minimum sizing requirements listed? NOTE: Smaller piping will cause performance problems.

Has water chemistry been checked?

Does water chemistry meet requirements?

If water chemistry does not meet requirements, have treatment measures been put in place?

Has the system been cleaned and ushed?

Has water piping been insulated for freeze protection?

Exhaust Vent and Combustion Air Intake Yes No

Is the appliance properly spaced from windows, doors, and other intake vents?

Has the appliance been installed at least one foot above exterior grade and one foot above normal snow accumulation level?

Install Condensate Piping / Tubing and Components Yes No

Have all condensate components included with the water heater been installed?

Is the condensate line piped with the approved materials listed in this manual?

Has the condensate line been routed to a laundry tub or other drain?

Has condensate line been protected from freezing with heat tape?

Has the installer ensured that the condensate does not drain onto a nished surface?

Install Gas Piping Yes No

Is the gas supply line a minimum of 3/4” in diameter?

Is the gas supply line length and diameter adequate to deliver the required BTUs?

Has gas supply line pressure been measured?

Does the gas type match the type indicated on the water heater rating plate?

Has a union and shut-o valve been installed?

Relief Valve Yes No

Is the Pressure Relief Valve properly installed and discharge line run to open drain?

Is the discharge line at least 3/4” in diameter and protected from freezing?

Wiring Yes No

Has the power and control been wired per water heater wiring diagram, this manual?

Have all DIP switches been set on the main water heater board?

Is the electrical connection polarity within water heater requirements?

Does the power supply voltage agree with the water heater rating plate? 120V AC?

Start-Up, Adjust, and Test Yes No

Has the water heater been started?

If necessary, has the water heater gas valve been adjusted?

Has the installation been customized per installation location requirements?

Have all customized system parameters been tested?

Has proper water heater operation been conrmed?

Burner Flame Yes No

Has the burner ame been checked?

Have combustion values been veried with a combustion analyzer?

If the ame does not appear normal, it may need to be cleaned by a qualied service technician. See Figure 62 for ame sight glass window location.

Final Installation Approvals

Signed by Technician Date

Table 34 - Installation Checklist

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 49

Part 13 - Maintenance

The water heater must be inspected and serviced annually, preferably at the start of the heating season, by a qualied service technician. In addition, the maintenance and care of the water heater as outlined in this manual must be performed by the user/ owner to assure maximum eciency and reliability. Follow the maintenance procedures given throughout this manual. Failure to perform the service and maintenance or follow the directions in this manual could damage the water heater or system components, resulting in substantial property damage, severe personal injury, or death.

Check the Surrounding Area

To prevent the potential of substantial property damage, severe personal injury, or death, eliminate all the materials listed in Table

7. from the area surrounding the water heater and the vicinity of the combustion air intake. If contaminates are found:

• Remove products immediately from area.

• If contaminates have been there for an extended period, call a qualied service technician to inspect the water heater for possible damage from acid corrosion.

If products cannot be removed, immediately call a qualied service technician to re-pipe the combustion air intake piping away from the contaminated areas.

Combustible/Flammable Materials

Do not store combustible materials, gasoline, or other ammable vapors or liquids near the water heater. If found, remove these materials immediately.

Air Contaminates

If allowed to contaminate combustion air, products containing chlorine or uorine will produce acidic condensate that will cause signicant damage to the water heater. Read the list of potential contaminates and areas likely to have these contaminates in Table 7. If any of these contaminates are in the room where the water heater is located, or combustion air is taken from one of the areas listed, the contaminants must be removed immediately or the intake pipe must be relocated to another area.

Ensure the Water Heater Cabinet is Closed

Ensure the water heater cabinet is closed. Tighten the two upper and lower screws to secure it. The cabinet must be closed while the water heater is running.

Check the Power Source

Make sure the power cord is properly connected. The main power line is connected to the manual switch box inside the water heater.

Check the Status of the Control Panel

Observe the Control Panel to ensure the water heater is powered on, and to check for any error codes. Clear any debris from the panel.

Check Exhaust Vent and Intake Pipe Terminations

Verify that the water heater exhaust vent and intake pipe terminations are clean and free of obstructions. Remove any debris from the exhaust vent or intake pipe openings. If removing the debris does not allow the water heater to operate correctly, contact your qualied service technician to inspect the water heater and the vent system.

Check Exhaust Vent and Intake Piping

Visually inspect the exhaust vent for any signs of blockage, leakage, or deterioration of the piping. Inspect the exhaust vent bracing. Ensure bracing is undamaged and in good condition. Notify a qualied service technician immediately if any problems are found.

Failure to inspect the venting system and have it repaired by a qualied service technician can result in vent system failure, causing severe personal injury or death.

Visually inspect the intake piping for any signs of blockage. Inspect the entire length of the intake pipe to ensure piping is intact and all joints are properly sealed. Inspect the intake pipe bracing. Ensure bracing is undamaged and in good condition. Notify a qualied service technician if any problems are found.

Check Pressure Relief Valve

• Visually inspect the primary pressure relief valve and discharge pipe for signs of weeping or leakage.

• If the pressure relief valve often weeps, the expansion tank may not be operating properly. Immediately contact a qualied service technician to inspect the water heater and system.

Check the Condensate Drain System

• While the water heater is running, check the discharge end of the condensate drain tubing. Ensure no ue gas is leaking from the condensate drain tubing by holding your ngers near the opening.

• If you notice ue gas leaking from the opening, this indicates a dry condensate drain trap. If problem persists, contact a qualied service technician to inspect the water heater and condensate line and rell the condensate trap.

• If applicable, check the condensate neutralizer and ensure it is full of condensate neutralizing marble chips.

Check Primary and Gas Piping

• Remove the water heater cover and perform a gas leak inspection following Operating Instructions, page 2, this manual. If gas odor or leak is detected, follow procedures on page 2. Call a qualied service technician.

• Visually inspect for leaks around the internal water heater water connections and around the heat exchanger. Visually inspect the external system piping, circulators, and system components and ttings. Immediately call a qualied service technician to repair any leaks

Check Wall Hung Model Brackets

• Check wall mount brackets. Ensure the brackets and mounting materials are secure and in good condition. Remount the water heater if necessary.

Have leaks xed at once by a qualied service technician. Failure to comply could result in substantial property damage, severe personal injury, or death.

Operate Pressure Relief Valve

• Before proceeding, verify that the relief valve outlet has been piped to a safe place of discharge, avoiding any possibility of scalding from hot water.

• Shut power o to the water heater. To avoid scalding, wait for water heater to cool before operating the relief valve.

To avoid water damage or scalding due to relief valve operation, a discharge line must be connected to the valve outlet and directed to a safe place of disposal. This discharge line must be installed by a qualied service technician or heating/plumbing installer in accordance with the water heater installation manual. The discharge line must be terminated so as to eliminate possibility of severe burns or property damage should the valve discharge.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 50

• Lift the relief valve lever. If water ows freely, release the lever and allow the valve to seat. Watch the end of the relief valve discharge pipe to ensure that the valve does not weep after the line has had time to drain. If the valve weeps, lift the lever again to attempt to clean the valve seat. If the valve does not properly seat and continues to weep, contact a qualied service technician to inspect the valve and system.

• If water does not ow from the valve when you completely lift the lever, the valve or discharge line may be blocked. Immediately shut the water heater down per instructions on page 2 and call a qualied service technician to inspect the valve and system.

• If relief valve seats properly, restore power to the water heater. Observe operation for ve minutes and ensure it operates properly.

Check the Burner

Clean the exterior of the burner.

Flushing the Water Heater

Flushing the heat exchanger is a complicated procedure that should only be performed by a qualied service technician. NOTE: Improper maintenance WILL VOID water heater warranty.

1. Disconnect electrical power to the water heater.

2. Close the shuto valves on both hot water outlet and cold

water inlet lines (V1 and V2). See Figure 56.

3. Connect one hose (D1, Figure 56) to the valve (V3) and place

the free end in a bucket. Connect one of the hoses (D3) to the circulation pump outlet and the cold water inlet line to valve V4. Connect the other hose (D2) to the circulation pump inlet and place the free end in the bucket.

Figure 49 - Flushing the Water Heater

4. Pour tankless water heater cleaning solution into the bucket.

Ensure the cleaning solution is approved for potable water systems. Place the drain hose (D1) and hose D2 to the pump inlet in the cleaning solution.

5. Open service valves (V3 and V4) on the hot water outlet and

cold water inlet lines.

6. Turn on the pump. Operate the pump and allow the cleaning

solution to circulate through the water heater for at least 1 hour at a rate of 4 gallons per minute. This will remove any possible harmful scale deposits.

7. Rinse the cleaning solution from the water heater as follows:

a. Remove the free end of drain hose D1 from the bucket. b. Close service valve V4 and open shuto valve V2. c. Do not open shuto valve V1. d. Allow water to ow through the water heater for 5 minutes. e. Close shuto valve V2.

8. Disconnect all hoses.

9. Remove the cold water inlet lter from the water heater and

clean out any residues.

10. Reinsert the lter and ensure the lter cap is securely

tightened.

11. Connect electrical power to the water heater.

12. Open a hot water faucet. Run the water heater continuously

for ve minutes to ensure all cleaning solution is purged from the system. Check for leaks and ensure the water heater is operating properly.

13. Properly dispose of used cleaning solution.

Maintenance Report

In unusually dirty or dusty conditions, care must be taken to keep water heater cabinet door in place at all times. Failure to do so VOIDS WARRANTY!

Allowing the water heater to operate with a dirty combustion chamber will hurt operation. Failure to clean the heat exchanger as needed by the installation location could result in water heater failure, property damage, personal injury, or death. Such product failures ARE NOT covered under warranty.

The combustion chamber insulation in this product contains ceramic ber material. Ceramic bers can be converted to cristobalite in very high temperature applications. The International Agency for Research on Cancer (IARC) has concluded, “Crystalline silica inhaled in the form of quartz or cristobalite from occupational sources is carcinogenic to humans (Group 1).”

• Avoid breathing dust and contact with skin and eyes.

• Use a NIOSH certied dust respirator (N95). This type of respirator is based on the OSHA requirements for cristobalite at the time this document was written. Other types of respirators may be needed depending on job site conditions. Current NIOSH recommendations can be found on the NIOSH website: http://www.cdc.gov/niosh/homepage.html. NIOSH approved respirators, manufacturers, and phone numbers are also listed on this website.

• Wear long-sleeved, loose tting clothing, gloves, and eye protection.

• Apply enough water to the combustion chamber lining to prevent dust.

• Wash potentially contaminated clothes separately from other clothing. Rinse clothes washer thoroughly.

NIOSH stated First Aid.

• Eye: Irrigate immediately.

• Breathing: Fresh air.

The water heater requires minimal periodic maintenance under normal conditions. However, in unusually dirty or dusty conditions, periodic vacuuming of the cover to maintain visibility of the display and indicators is recommended. Periodic maintenance should be performed once a year by a qualied service technician to assure that all the equipment is operating safely and eciently. The owner should make necessary arrangements with a qualied heating contractor for periodic maintenance of the water heater. Installer must also inform the owner that the lack of proper care and maintenance of the water heater may result in a hazardous condition.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 51

INSPECTION ACTIVITIES DATE LAST COMPLETED

PIPING

Near water heater piping

Check water heater and system piping for any sign of leakage. Leaking pipes could cause property damage. Make sure all piping

1st YEAR 2

YEAR 3

is properly supported. Ensure freeze protection is intact and in good condition. Flush tankless heat exchanger annually (more in hard water conditions). See User’s Information manual for instructions.

Vent Check condition of the exhaust vent and intake. Check for

obstructions exhaust and intake termination points.

Gas Check Gas piping, test for leaks and signs of aging. Make sure all

pipes are properly supported.

SYSTEM

Visual Do a full visual inspection of all system components.

Functional Test all functions of the system (Heat, Safeties)

Temperatures Verify safe settings on water heater or Anti-Scald Valve

Temperatures Verify programmed temperature settings

ELECTRICAL

Connections Check wire connections. Make sure they are tight.

Smoke and CO detector Verify devices are installed and working properly. Change batteries

if necessary.

Circuit Breakers Check to see that the circuit breaker is clearly labeled. Exercise circuit

breaker.

Switch and Plug Verify ON/OFF switch and convenience plug are both functional

CHAMBER/BURNER

Combustion Chamber Check burner tube and combustion chamber coils. Clean according

to maintenance section of manual. Vacuum combustion chamber.

Spark Electrode Clean. Set gap at 1/8”.

CONDENSATE

Condensate Trap Clean debris from the condensate trap. Fill with clean water.

Neutralizer Check condensate neutralizer. Replace if necessary.

Condensate hose Disconnect condensate hose. Clean out dirt and re-install. (NOTE:

Verify the ow of condensate, making sure that the hose is properly connected during nal inspection.)

Freeze Protection Ensure freeze protection is intact and in good condition.

GAS

Pressure Measure incoming gas pressure (3.5” to 14” W.C.)

Pressure Drop Measure drop in pressure on light o (no more than 1” W.C.)

Check gas pipe for

Check piping for leaks. Verify that all are properly supported.

leaks

COMBUSTION

CO/CO2 Levels Check CO and CO2 levels in Exhaust. Record at high and low re.

SAFETIES

ECO (Energy Cut Out) Check continuity on Flue and Water ECO. Replace if corroded.

FINAL INSPECTION

Check list Verify that you have completed entire check list. WARNING: FAILURE

TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

Homeowner Review what you have done with the homeowner.

TECH SIGN OFF

YEAR 4th YEAR*

Table 35 - *Continue annual maintenance beyond the 4th year as required.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 52

Part 13 - Replacement Parts

NUMBER DESCRIPTION PART NUMBER NUMBER DESCRIPTION PART NUMBER

B-1 M3 X 6 PH + M/S 7855P-384 B-12 M4 X 15 PW + M/S 7855P-395

B-2 M4 X 8 PH + Self Tapping 7855P-385 B-13 M4 X 20 TH + Self Tapping 7855P-396

B-3 M4 X 8 TH + Self Tapping 7855P-386 B-14 M5 X 14 Flange Bolts + M/S 7855P-397

B-4 M4 X 8 TH + M/S 7855P-387 B-15 M5 X 10 TH+ M/S 7855P-453

B-5 M4 X 10 FH + M/S 7855P-388 B-16 M4 X 9 PH.PW + Self Tapping 7855P-296

B-6 M4 X 10 TH + Self Tapping 7855P-389 B-17 M4 X 12 Hex Screw 7855P-665

B-7 M4 X 10 TH + M/S 7855P-390 B-18 M4 X 10MM Bird Screen Screw 7855P-664

B-8 M4 X 10 Flat Head 7855P-391 B-19 6-20 x 1/2 Self Drilling Screw 7350P-400

B-9 M4 X 12 PH + M/S 7855P-392 B-20 M5 X 12MM PH Screw 7865P-023

B-10 M4 X 12 TH + M/S 7855P-393 N-1 M4 Nut 7855P-398

B-11 M4 X 14 PH + Self Tapping 7855P-394 N-2 M5 Nut 7855P-399

Table 37 - Replacement Bolts and Nuts

Figure 50 - Replacement Parts - Outdoor Wall Model

Number Description Part Number Number Description Part Number

Table 36 - Replacement Parts

Cabinet Assembly See Figure 52-54

1 1/4” FIP 304 SS Cap 7860P-004

2” Outdoor Exhaust Adapter 7850P-259

2” Vent Pipe Assembly 7860P-100

Outdoor Vent Pipe Bracket 7855P-662

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Outdoor Top Cover 7855P-623

2” Bird Screen, Outdoor 7855P-667

Outdoor Front Cover 7855P-624

Wiring, Main Power 7860P-101

Terminal Block 7855P-138

Page 53

Figure 51 - Replacement Parts - Outdoor Floor Model

Number Description Part Number Number Description Part Number

Table 38 - Replacement Parts

Cabinet Assembly See Figure 66

1 1/4” FIP 304 SS Cap 7860P-004

2” Outdoor Exhaust Adapter 7850P-259

2” Vent Pipe Assembly 7860P-100

Outdoor Vent Pipe Bracket 7855P-662

Outdoor Top Cover 7855P-623

2” Bird Screen, Outdoor 7855P-667

Outdoor Front Cover 7855P-624

Terminal Block 7855P-138

Wiring, Main Power 7860P-101

Right Side Panel Assembly 7860P-102

3/4” ID SS Gas Flex - 18” Long 7865P-016

Handle, Front Cover 7600P-033

Front Cover Assy, Floor Stand 7865P-004

Condensate Hose 7855P-089

Pump Assembly 7860P-103

Back Panel, Floor Stand 7865P-025

1” ID SS Flex - 24” Long 7865P-014

Left Side Panel, Floor Stand 7865P-008

Base Assembly, Floor Stand 7865P-002

Anchors and Wall Bracket 7850P-084

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 54

B-6

B-3

B-6

B-5

B-3

B-5

B-3

B-13

B-10

B-3

Figure 52 - Cabinet Replacement Parts

B-3

B-8

B-5

B-3

NUMBER DESCRIPTION PART NUMBER NUMBER DESCRIPTION PART NUMBER

1 Cabinet Assembly 7860P-005 10 Display Panel Bracket 7855P-413

2 Top Wall Mount Bracket 7850P-068 11 Terminal Blocks Bracket 7855P-434

3 Bottom Wall Mount Bracket 7850P-092 12 Control Board 7855P-408

4 Air Vent 7855P-063 13 Display Panel 7860P-006

5 Air Vent Adapter 7855P-454 14 Manual Power Switch 7855P-014

6 Air Vent Adapter Gasket 15 Condensate Block APS 7855P-017

7 Control Board Bracket 7855P-412 16 High Voltage Terminal Block 7860P-007

8 Air Pressure Switch 7855P-262 17 Low Voltage Terminal Block 7860P-008

9 Ignition Transformer 7855P-007 18 DHW Pressure Gauge 7860P-010

Table 39 - Cabinet Replacement Parts

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 55

Figure 53 - Heat Exchanger Replacement Parts

NUMBER DESCRIPTION PART NUMBER NUMBER DESCRIPTION PART NUMBER

30 Exhaust Pipe Assembly 7855P-415 33 HX Dual (OP/OH) Temperature Sensor 7855P-030

30-1 Exhaust Temperature Sensor Clip 7855P-349 34 Water Level Detection Sensor 7855P-029

30-2 Exhaust Temperature Sensor

30-3 Exhaust Temperature Sensor O-Ring 36 Flame Sensor Bracket 7855P-356

31 Exhaust Pipe Gasket 7855P-418 36-1 Flame Sensor Cover 7855P-357

32 Heat Exchanger Assembly 7860P-011 37 Outlet Pipe 7860P-012

32-1 Burner Body Assembly 7855P-417 37-1 Outlet Pipe Gasket 7855P-074

32-2 Burner Overheat Switch 7855P-066 38 Inlet Pipe 7855P-422

32-3 Burner Body 7855P-606 38-1 Inlet Pipe Gasket 7855P-074

32-4 Burner Gasket 7855P-419 39 DHW Inlet Sensor (Rt) 7855P-097

32-5 Ceramic Fiber Burner 7855P-420 39-1 Inlet Sensor Gasket 7855P-364

32-6 Ignition Rod 7855P-607 40 Condensate Trap 7855P-605

32-7 Igniter Gasket 7855P-252 41 Sight Glass Assembly 7855P-401

32-8 Heat Exchanger Top 7855P-619 42 Outlet Temperature Sensor (St) 7855P-137

32-9 Burner Refractory 7855P-612

Table 40 - Heat Exchanger Replacement Parts

7855P-092

35 Flame Sensor 7855P-031

Not

Shown

Heat Exchanger Gasket 7855P-461

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 56

Figure 54 - Combustion System Replacement Parts

NUMBER DESCRIPTION PART NUMBER NUMBER DESCRIPTION PART NUMBER

45 Burner Inlet Channel (w/ Damper) 7855P-424 54 APS Hose Fitting 7855P-375

46 Air Damper 7855P-618 55 Gas Valve Assembly 7855P-431

47 Air Damper Guide 7855P-369 55-1 Gas Valve Outlet Adapter 7855P-232

48 Fan Outlet Gasket 7855P-425 55-2 Gas Valve O-Ring 7855P-076

49 Burner Inlet Channel Gasket 7855P-426 55-3 Gas Valve 7855P-034

50 Fan and Mixer Assembly 7855P-427 55-4 Gas Valve Inlet Adapter 7850P-077

50-1 Fan 7855P-025 55-5 Gas Valve Bracket 7855P-436

50-2 Fan O-Ring 7855P-371 56 1/2” Gas Pipe Gasket 7855P-221

50-3 Air Gas Mixer, 30mm 7855P-609

50-4 Air Gas Mixer Gasket 7855P-428 Gas Orice (LP) 6.2mm 7855P-435

Gas Orice (NG) 8.3mm 7855P-610

50-5 Air Gas Mixer (outer part) 7855P-608 58 Gas Pipe (to mixer) 7855P-432

51 Air Intake Hose Top Clamp (Φ89) 7855P-429 59 Gas Pipe (to gas valve) 7855P-433

52 Air Intake Hose 7855P-430 60 Gas Inlet Adapter (3/4”) 7855P-382

53 Air Intake Hose Bottom Clamp 7855P-429

Table 41 - Combustion System Replacement Parts

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 57

Limited Warranty for CGH-199 Water Heaters

For Commercial Use

HTP warrants each instantaneous water heater and its parts to be free from defects in materials and workmanship according to the following terms, conditions, and time periods. UNLESS OTHERWISE NOTED THESE WARRANTIES COMMENCE ON THE DATE OF INSTALLATION. This limited warranty is only available to the original consumer purchaser (hereinafter “Owner”) of the water heater, and is non-transferable.

Heat Exchanger Components

Five (5) Years One (1) Year*

COVERAGE

A. During the rst year after the original date of installation, HTP warrants that it will repair or replace, at its option, any defective or malfunctioning component of the water heater with a component of equivalent size and current model. Replacement components will be warranted for ninety (90) days. B. Should a defect or malfunction result in a leakage of water from the water heater within the above-stated warranty periods due to defective material or workmanship, malfunction, or failure to comply with the above warranty, with such defect or malfunction having been veried by an authorized HTP representative, HTP will replace the defective or malfunctioning water heater with a replacement of the nearest comparable model available at the time of replacement. The replacement water heater will be warranted for the unexpired portion of the applicable warranty period of the original water heater. C. In the event of a leakage of water of a replacement water heater due to defective material or workmanship, malfunction, or failure to comply with the above warranty, HTP reserves the right to refund to the Owner the published wholesale price available at the date of manufacture of the original water heater. D. If government regulations, industry certication, or similar standards require the replacement water heater or component(s) to have features not found in the defective water heater or component(s), the Owner will be charged the dierence in price represented by those required features. If the Owner pays the price dierence for those required features and/or to upgrade the size and/or other features available on a new replacement water heater or component(s), the Owner will also receive a complete new limited warranty for that replacement water heater or component(s). E. If at the time of a request for service the Owner cannot provide a copy of the original sales receipt or the warranty registration, the warranty period for the water heater shall then be deemed to have commenced thirty (30) days after the date of manufacture of the water heater and NOT the date of installation of the water heater. F. This warranty extends only to water heaters utilized in heating applications that have been properly installed by qualied professionals based upon the manufacturer’s installation instructions. G. It is expressly agreed between HTP and the Owner that repair, replacement, or refund are the exclusive remedies of the Owner.

OWNER RESPONSIBILITIES

The Owner or Installer must:

1. Have a relief valve bearing the listing marks of the American Society of Mechanical Engineers (ASME) installed with the water heater assembly in accordance with federal, state, and local codes.

2. Have a vacuum relief valve certied to ANSI Z21.22 - Relief Valves for Hot Water Supply Systems installed with the water heater assembly in accordance with federal, state, and local codes and in installations prone to vacuum related damages.

3. Maintain the water heater in accordance with the maintenance procedure listed in the manufacturer’s provided instructions. Preventive maintenance can help avoid any unnecessary breakdown of the water heater and keep it running at optimum eciency.

4. Maintain all related system components in good operating condition.

5. Use the water heater in an open system, or in a closed system with a properly sized and installed thermal expansion tank.

6. Use the water heater at water pressures not exceeding the working

pressure shown on the rating plate.

7. Keep the water heater free of damaging scale deposits.

8. Make provisions so if the water heater or any component or connection thereto should leak, the resulting ow of water will not cause damage to the area in which it is installed.

WARRANTY EXCLUSIONS

This limited warranty will not cover:

1. Any water heater purchased from an unauthorized dealer or online retailer.

2. Any water heater not installed by a qualied heating installer/service technician, or installations that do not conform to ANSI, CSA, and/or UL standards, as well as any applicable national or local building codes.

3. Service trips to teach you how to install, use, maintain, or to bring the water heater installation into compliance with local building codes and regulations.

4. The workmanship of any installer. The manufacturer disclaims and does not assume any liability of any nature caused by improper installation, repair, or maintenance.

5. Electricity or fuel costs, or increased or unrealized savings for same, for any reason whatsoever.

6. Any water damage arising, directly or indirectly, from any defect in the water heater or component part(s) or from its use.

7. Any incidental, consequential, special, or contingent damages or expenses arising, directly or indirectly, from any defect in the water heater or the use of the water heater.

8. Failure to locate the water heater in an area where leakage of the tank or water line connections and the relief valve will not result in damage to the area adjacent to the water heater or lower oors of the structure, as well as failure to install the water heater in or with a properly sized drain pan routed to an approved drainage location.

9. Any failed components of the heat system not manufactured by HTP as part of the water heater.

10. Water heaters repaired or altered without the prior written approval of HTP.

11. Damages, malfunctions, or failures resulting from improper installation, or failure to install the water heater in accordance with applicable building codes/ordinances or good plumbing and electrical trade practices; or failure to operate and maintain the water heater in accordance with the manufacturer’s provided instructions.

12. Damages, malfunctions, or failures resulting from failure to operate the water heater at pressures not exceeding the working pressure shown on the rating label.

13. Failure to operate the water heater in an open system, or in a closed system with a properly sized and installed thermal expansion tank.

14. Failure or performance problems caused by improper sizing of the water heater, expansion device, piping, or the gas supply line, the venting connection, combustion air openings, electric service voltage, wiring or fusing.

15. Damages, malfunctions, or failures caused by improper conversion from natural gas to LP gas or LP gas to natural gas.

16. Damages, malfunctions, or failures resulting from vacuum conditions.

17. Damages, malfunctions, or failures caused by operating the water heater with modied, altered, or unapproved parts.

18. Damages, malfunctions, or failures caused by abuse, accident, re, ood, freeze, lightning, electrochemical reaction, acts of God and the like.

19. Failures (leaks) caused by operating the water heater in a corrosive or contaminated atmosphere.

20. Damages, malfunctions, or failures caused by operating the water heater with an empty or partially empty tank (“dry ring”), or failures caused by operating the water heater when it is not supplied with potable water, free to circulate at all times.

21. Failure of the heater due to the accumulation of solid materials and lime deposits.

22. Any damage or failure resulting from improper water chemistry, or heating anything other than potable water. DEFINITION OF POTABLE WATER - Potable water is dened as drinkable water supplied from utility or well water in compliance with EPA secondary maximum contaminant levels (40 CFR Part 143.3) as shown in the table.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 58

EPA DEFINITION OF POTABLE WATER

Contaminant Level

Total Hardness

(Commercial Use - 140oF and above

water temperature)

120 mg/l

(7 grains/gallon)

Aluminum 0.05 to 0.2 mg/l

Chloride 100 mg/l

Color 15 color units

Copper 1.0 mg/l

Corrosivity Non-corrosive

Fluoride 2.0 mg/l

Foaming Agents 0.5 mg/l

Iron 0.3 mg/l

Manganese 0.05 mg/l

Odor

3 threshold odor

number

pH 6.5 – 8.5

Silver 0.1 mg/l

Sulfate 250 mg/l

Total Dissolved Solids (TDS) 500 mg/l

Zinc 5 mg/l

Dissolved Carbon Dioxide (CO2) 15 mg/l or ppm

23. Any damages, malfunctions, or failures resulting from the use of dielectric unions.

24. Production of noise, taste, odors, discoloration, or rusty water.

25. Water heaters replaced for cosmetic reasons.

26. Components of the water heater that are not defective, but must be replaced during the warranty period as a result of reasonable wear and tear.

27. Components of the water heater that are subject to warranties, if any, given by their manufacturers; HTP does not adopt these warranties.

28. Damages, malfunctions, or failures resulting from the use of any attachment(s) not supplied by HTP.

29. Water heaters installed outside the fty states (and the District of Columbia) of the United States of America and Canada.

30. Water heaters moved from the original installation location.

31. Water heaters that have had their rating labels removed.

PROCEDURES FOR WARRANTY SERVICE REQUESTS

Any claim for warranty assistance must be made immediately upon nding the issue. First, please consult the HTP Warranty Wizard (http:// www.htproducts.com/Warranty-Wizard.html) to check warranty eligibility. You may also contact HTP Technical Support at 1-800-3239651 for questions or assistance. Warranty coverage requires review and approval of the issue with HTP Technical Support or through the Warranty Wizard prior to a full unit replacement. Any claim for warranty reimbursement will be rejected if prior approval from HTP is not obtained in advance of a full unit replacement. Final determination will be made as part of the warranty claim process.

When submitting a warranty claim the following items are required:

1. Proof of purchase or installation of the product – Typically a copy

of the invoice from the installing contractor, the receipt of the purchase of the product, or an original certicate of occupancy for a new home.

2. Clear pictures (or video) of the following:

a. Serial number tag (sticker) b. The product c. The product issue / failure whenever possible d. A picture of the piping near the product e. For gas red products, a picture of the venting, including how it exits the building

All claims will be reviewed by HTP within three (3) business days. If

additional information is required and requested by the HTP Claims Department you will have thirty (30) days to provide it. When all requested information is provided HTP will respond within three (3) business days. The claim will be automatically closed if requested information is not provided within thirty (30) days. Claims will not be reopened without HTP Warranty Supervisor approval. During the claims process a product that must be replaced will be given a designation of either a) eld scrap, or b) return to HTP. If the product must be returned to HTP, the returned product must arrive at HTP within thirty (30) days of the date of our request to return the product. After receipt of the returned product HTP may require as many as thirty (30) additional days for product testing. NOTE: Any components or heaters returned

to HTP for warranty analysis will become the property of HTP and will not be returned, even if credit is denied.

If you have questions about the coverage of this warranty, please contact HTP at the following address or phone number: HTP, 272 Duchaine Blvd., New Bedford, MA, 02745, Attention: Warranty Service Department, 1(800) 323-9651.

SERVICE, LABOR AND SHIPPING COSTS

Except when specically prohibited by the applicable state law, the Owner, and not the Manufacturer, shall be liable for and shall pay for all charges for labor or other expenses incurred in the removal, repair, or replacement of the appliance or any component part(s) claimed to be defective or any expense incurred to remedy any defect in the product. Such charges include, but are not necessarily limited to:

1. All freight, shipping, handling, and delivery costs of forwarding a new appliance or replacement part(s) to the owner.

2. All costs necessary or incidental in removing the defective appliance or component part(s) and installing a new appliance or replacement part(s).

3. All administrative fees incurred by the Owner, as well as material required to complete, and/or permits required for, installation of a new appliance or replacement part(s), and

4. All costs necessary or incidental in returning the defective water heater or component part(s) to a location designated by the manufacturer.

LIMITATIONS OF YOUR HTP WARRANTY AND REMEDIES

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE GIVEN AND ACCEPTED TO THE FURTHEST EXTENT UNDER APPLICABLE LAW IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER OR NOT ARISING FROM HTP’S NEGLIGENCE, ACTUAL OR IMPUTED. THE REMEDIES OF THE OWNER SHALL BE LIMITED TO THOSE PROVIDED HEREIN TO THE EXCLUSION OF ANY OTHER REMEDIES INCLUDING WITHOUT LIMITATION, INCIDENTAL OR CONSEQUENTIAL DAMAGES, SAID INCIDENTAL AND CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROPERTY DAMAGE, LOST PROFIT OR DAMAGES ALLEGED TO HAVE BEEN CAUSED BY ANY FAILURE OF HTP TO MEET ANY OBLIGATION UNDER THIS AGREEMENT INCLUDING THE OBLIGATION TO REPAIR AND REPLACE SET FORTH ABOVE. NO AGREEMENT VARYING OR EXTENDING THE FOREGOING WARRANTIES, REMEDIES OR THIS LIMITATION WILL BE BINDING UPON HTP. UNLESS IN WRITING AND SIGNED BY A DULY AUTHORIZED OFFICER OF HTP. THE WARRANTIES STATED HEREIN ARE NOT TRANSFERABLE AND SHALL BE FOR THE

BENEFIT OF THE OWNER ONLY.

NO OTHER WARRANTIES

This warranty gives you specic legal rights, and you may also have other rights that vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you. These are the only written warranties applicable to the commercial water heater manufactured and sold by HTP. HTP neither assumes nor authorizes anyone to assume for it any other obligation or liability in connection with said commercial water heaters. HTP reserves the right to change specications or discontinue models without notice.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 59

Notes

lp-673 Rev. 000 Rel. 001 Date 8.30.18

Page 60

Customer Installation Record Form

The following form should be completed by the installer for you to keep as a record of the installation in case of a warranty claim. After reading the important notes at the bottom of the page, please also sign this document.

Customer’s Name

Date of Installation

Installation Address

Product Name / Serial Number(s)

Comments

Installer’s Code / Name

Installers Phone Number

Signed by Installer

Signed by Customer

Installation Notes

IMPORTANT

Customer: Please only sign after the installer has fully reviewed the installation, safety, proper operation, and maintenance of the system. If the system has any problems please call the installer. If you are unable to make contact, please call your sales representative. Distributor / Dealer: Please insert contact details.

lp-673 Rev. 000 Rel. 001 Date 8.30.18

HTP CGH-199O Installation, Start-up, Maintenance, Parts And Warranty

Specifications and Main Features

Frequently Asked Questions

User Manual