HTI Vivo Media+, Vivo Media +5 User Manual

Vivo Media+

& Vivo Media +5

User Guide

M1-M5

Radio

Mute

UP

Down

Flash

Speaker

Redial

Vol-/Vol+

Hold

SET

Play

SOS

Snooze

Bluetooth

FUNCTION KEY DIAGRAM

2. Installation before Use

Put the package handset into the stand cradle; connect the cord line, handset line and
the power adapter

FUNCTION INSTRUCTIONS

1、 Place a call / Answer a Call
2、 Pick up the handset and press the ON/OFF button to turn it on. When the phone is

on, a light will come on to show you that the phone is connected and you can make a
call. To end the call, press the ON/OFF button. When the phone is in use and a new call
is coming through, you will hear the ringtone and the indicator will flash. When this
happens, press the ON/OFF button on the handle to answer the call. At this time, the
any music playing on your iphone is paused, and will resume playing automatically
once you have ended the call.

2、Volume
Press the volume adjustment button VOL+ or VOL- to increase or lower sound , there
are 4 options for volume control,” 1- 4” when you pick up the handset.

3、 Hold
When you are taking a call, press the HOLD key, the LED light will slowly blink red,
indicating the call is on hold.
Press the HOLD key again to resume the call. The LED will remain lit and stop blinking
to let you know that the phone is in use.

4、 Flash
The flash time can be selected from 100~1000MS. Please refer to the passwords
INSTRUCTIONS and adjust accordingly. The default time is 600MS. Pick up the
handset and press Flash key help you transfer or quickly disconnect a call. **P0 is
100ms; **P1 is 300ms; **P2 is 600ms; **P3 is 1000ms. Press and hold the last digit for 3
seconds.

PASSWORDS INSTRUCTIONS

5 Redial
Press the REIDAL key to dial the last number out from handset.

6 Memory Key Settings； Mn=M1-M10。
Memory key Settings: In the on-hook mode, press “ phone' number + hold Mn for 3
seconds until the indicator light is blinks, which shows that the corresponding number has
been saved successfully. Mn=M1~M10
7 Use SOS key
In the on-hook mode, enter the number and holding SOS key for about 3 seconds until the
in use light is blinks.
Pick up the handset and press SOS key to connect with emergency services.

8 Mute

To mute a call by pressing MUTE button only, a blinking light will remind you into mute
.During this time the other cannot hear you. Press mute key again to restore the
conversation. When the mute button is pressed during a call, the indicator light flashes to
remind you that you are in mute mode, you will be able to hear the caller but they will not be
able to hear. When you press this button again, the indicator light is on and the light is
restored. To normal call status.

9 Time setting

In the standby state (no play or pause playback), press and hold the SETTINGS button
to enter the time setting. The hour number is flashing, press the +, - buttons to adjust,
press the SETTINGS button to confirm and then flash, press the +/- button to adjust the
minute. Press the SETTINGS button again to confirm.

10 Alarm setting

In the standby state (no play or pause playback), press the setting button, the alarm
icon on the display lights up, the time setting mode is the same as above; when the
alarm is reached, press the snooze button to enter the snooze state (9 minutes later)
The alarm is activated. When the other buttons are pressed, the alarm will stop and the
alarm icon will go out.

11 Music playing

Before use
First connect the multimedia phone to the telephone line and plug in the DC5V/1.5A
power adapter, and confirm that the clock screen is displayed before it can be used
normally.

Clock operation

a) Clock setting

In the standby state, press and hold the “Settings” button for 3 seconds, when the hours

are flashing, press “UP” or “DOWN” to adjust the hour, press “Setting” again, the minute

number is flashing, press “UP” ” or “DOWN button” to adjust the points, and then press
the “Settings” button to confirm.

b) Alarm setting

In the standby mode, press the “Settings” button, the alarm icon appears in the upper

right corner of the clock, and the hour number is flashing. The adjustment method is the
same as the clock setting.
c Alarm clock cancellation
When the alarm is set, and you want to cancel the alarm before use. Press the

“Settings” button to cancel. When you are ringing, press any function button to cancel.

After canceling the alarm, the icon of the clock in the upper right corner will go out.

Description

Password

Remark

Set FLASH time: 100ms

**P0

Note: all the passwords setting should
at OFF-HOOK mode and you have to
holding the last digit of password at

least 3 seconds, “P” is setting on the

“REDIAL” key.

300ms

**P1

600ms

**P2

1000ms

**P3

d) alarm clock snooze function

When the alarm is ringing, press the “ZNOOZE button” (snake button) to stop the alarm,

the icon in the upper right corner of the clock is still lit, and the alarm will be activated after
10 minutes.
e) Clock brightness adjustment (power-on default is low brightness)
Press the “VOL+” and “VOL-” buttons in standby mode to adjust the display brightness.

2.3, media playback

a) FM radio

When the “Radio” button is pressed in the standby state, the radio is turned on. In the

upper left corner of the display, the word “RADIO FM” is displayed. Press the “UP button”
or “DOWN button” to adjust the listening radio broadcast. Press the “VOL+” and “VOL-”
buttons. Adjust the volume and press the “Radio” button again to turn off the radio.

b) AUX input playback
In the standby state, use the AUX audio cable to insert the audio source into the AUX input

port on the back of the media phone. The right side of the display shows “AUX”, press the
“Play” button to start play, the AUX icon flashes, and then press the “Play” button to play.

Pause, the AUX word on the right side of the screen goes out after the AUX line is
removed
c) Bluetooth playback
When using Bluetooth for the first time, you must pair the source device with the
multimedia phone to play it. The pairing has automatic and manual pairing:
A. Automatic pairing (optional according to order requirements): In the standby state, the
NFC-enabled audio source device will automatically enter the pairing when it is close to
the media phone panel, and the phone's Bluetooth indicator light will start to flash when
the two devices are connected. , the indicator light turns on for a while, and the Bluetooth
icon on the display lights up;

B. Manual pairing: In the standby state, press the “Bluetooth” button, the Bluetooth

indicator flashes quickly. At this time, the Bluetooth function of the source device is turned
on, the Bluetooth indicator of the successful media phone is long, and the Bluetooth icon is
lit. C. Playback: When the device is successfully paired, the Bluetooth icon on the display

lights up, press the “Play” button to play, the Bluetooth icon flashes (the indicator light

flashes slowly), press “UP” or “DOWN” Select to play the song and press "VOL+" And
the “VOL-” button to adjust the volume.

d) Source Switching
A. When both AUX and Bluetooth are connected to the media phone, the display
simultaneously displays the AUX and Bluetooth icons. In the standby or paused
playback state, press the “UP” or “DOWN” button to select the switch. The selected
icon is in the Flash, press the "Play" button to play;

B. Regardless of whether AUX or Bluetooth is playing, press the “Radio” button to

switch to the radio state.
To switch to other playback in the radio state, you must first turn off the radio, press the
"UP" button or Select the “DOWN button” (select the corresponding icon to flash), press
the “Play” button to play.

Hotel Technology International Limited
1st Floor • 239 Kensington High Street
London W8 6SA, United Kingdom
Telephone: [phone], Fax: [phone]
Email: [e-mail] • Website www.hotel-tech.com

© Hotel Technology International Limited. All Rights reserved