Safety and
regulatory guide
2 Safety and regulatory guide
Please read before proceeding
THE BATTERY IS NOT FULLY CHARGED WHEN YOU TAKE THE
DEVICE OUT OF THE BOX.
Privacy restrictions
Some countries require full disclosure of recorded telephone
conversations.
Important health information and safety precautions
When using this product, the safety precautions below must be taken to
avoid possible legal liabilities and damages.
Retain and follow all product safety and operating instructions. Observe all
warnings in the operating instructions on the product.
To reduce the risk of bodily injury, electric shock, fire, and damage to the
equipment, observe the following precautions.
Electrical safety
This product is intended for use when supplied with power from the
designated battery or power supply unit. Other usage may be dangerous
and will invalidate any approval given to this product.
Safety precautions for proper grounding installation
CAUTION: Connecting to improperly grounded equipment can result in an
electric shock to your device.
This product is equipped with a USB Cable for connecting with desktop or
notebook computer. Be sure your computer is properly grounded (earthed)
before connecting this product to the computer. The power supply cord of
a desktop or notebook computer has an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet
which is properly installed and grounded in accordance with all local
codes and ordinances.
Safety precautions for power supply unit
Use the correct external power source
A product should be operated only from the type of power source
indicated on the electrical ratings label. If you are not sure of the type of
power source required, consult your authorized service provider or local
power company. For a product that operates from battery power or
other sources, refer to the operating instructions that are included with
the product.
This product should be operated only with the following designated
power supply unit(s).
AC adapter:
Safety and regulatory guide 3
WARNING: To reduce risk of fire or burns, do not
disassemble, crush, puncture, short external contacts,
expose to temperature above 60° C
(140° F), or dispose of in fire or water. Recycle or dispose
of used batteries according to the local regulations or
reference guide supplied with your product.
HTC, Model TC U250
Handle battery packs carefully
This product contains a Lithium-ion polymer or Lithium-ion battery. There is a
risk of fire and burns if the battery pack is handled improperly. Do not attempt
to open or service the battery pack. Do not disassemble, crush, puncture,
short external contacts or circuits, dispose of in fire or water, or expose a
battery pack to temperatures higher than 60˚C (140˚F).
Take extra precautions
Keep the device dry and away from water or any liquid as it may
cause a short circuit.
The phone should only be connected to products that bear the
USB-IF logo or have the completed the USB-IF compliance program.
Only use the battery with a charging system that has been qualified
with the system per this standard, IEEE-Std-1725. Use of an
unqualified battery or charger may present a risk of fire, explosion,
leakage or other hazard.
Avoid dropping the phone. If the phone is dropped, especially on a
hard surface, and the user suspects damage, take it to a service
centre for inspection.
If the battery leaks:
Do not allow the leaking fluid to come in contact with skin or clothing.
If already in contact, flush the affected area immediately with clean
water and seek medical advice.
Do not allow the leaking fluid to come in contact with eyes. If already
in contact, DO NOT rub; rinse with clean water immediately and seek
medical advice.
Take extra precautions to keep a leaking battery away from fire as
there is a danger of ignition or explosion.
Safety precautions for direct sunlight
4 Safety and regulatory guide
Keep this product away from excessive moisture and extreme
temperatures. Do not leave the product inside a vehicle or in places where
the temperature may exceed 60°C (140°F), such as on a car dashboard,
window sill, or behind a glass that is exposed to direct sunlight or strong
ultraviolet light for extended periods of time. This may damage the product,
overheat the battery, or pose a risk to the vehicle.
Prevention of hearing loss
CAUTION: Permanent hearing loss may occur if earphones or headphones are
used at high volume for prolonged periods of time.
Safety in aircraft
Due to t he pos sible interferen ce caus ed by t his pro duct to an aircraft’s
navigati on syst em and its communic ations network , using t his devi ce’s
phone function on board an airplane is against the law in most countries. If
you want to use this device when on board an aircraft, remember to turn
off your phone by switching to Airplane Mode.
Environment restrictions
Do not use this product in gas stations, fuel depots, chemical plants or
where blasting operations are in progress, or in potentially explosive
atmospheres such as fuelling areas, fuel storehouses, below deck on
boats, chemical plants, fuel or chemical transfer or storage facilities, and
areas where the air contains chemicals or particles, such as grain, dust, or
metal powders. Please be aware that sparks in such areas could cause an
explosion or fire resulting in bodily injury or even death.
Explosive atmospheres
When in any area with a potentially explosive atmosphere or where
flammable materials exist, the product should be turned off and the user
should obey all signs and instructions. Sparks in such areas could cause
an explosion or fire resulting in bodily injury or even death. Users are
advised not to use the equipment at refueling points such as service or
gas stations, and are reminded of the need to observe restrictions on the
use of radio equipment in fuel depots, chemical plants, or where blasting
operations are in progress. Areas with a potentially explosive atmosphere
are often, but not always, clearly marked. These include fueling areas,
below deck on boats, fuel or chemical transfer or storage facilities, and
areas where the air contains chemicals or particles, such as grain, dust, or
metal powders.
Road safety
Full attention must be given to driving at all times in order to reduce the
risk of an accident. Using a phone while driving (even with a hands free kit)
causes distraction and can lead to an accident. You must comply with
Safety and regulatory guide 5
local laws and regulations restricting the use of wireless devices while
driving.
Safety precautions for RF exposure
Avoid using your phone near metal structures (for example, the steel
frame of a building).
Avoid using your phone near strong electromagnetic sources, such as
microwave ovens, sound speakers, TV and radio.
Use only original manufacturer-approved accessories, or accessories
that do not contain any metal.
Use of non-original manufacturer-approved accessories may violate
your local RF exposure guidelines and should be avoided.
Hearing aids
Some digital wireless phones may interfere with some hearing aids. In the
event of such interference, you may want to consult your service provider,
or call the customer service line to discuss alternatives.
Electrical safety
Accessories
Use only approved accessories.
Do not connect with incompatible products or accessories.
Take care not to touch or allow metal objects, such as coins or key
rings, to contact or short-circuit the battery terminals.
Connection to a car
Seek professional advice when connecting a phone interface to the
vehicle electrical system.
Faulty and damaged products
Do not attempt to disassemble the phone or its accessory.
Only qualified personnel must service or repair the phone or its
accessory.
General precautions
You alone are responsible for how you use your phone and any
consequences of its use. You must always switch off your phone
wherever the use of a phone is prohibited. Use of your phone is subject to
safety measures designed to protect users and their environment.
Avoid applying excessive pressure to the device
Do not apply excessive pressure on the screen and the device to
prevent damaging the m and remove t he devi ce from y our pa nts’ pocket
before sitting down. It is also recommended that you store the device in
a protective case and only use the device stylus or your finger when
interacting with the touch screen. Cracked display screens due to
6 Safety and regulatory guide
improper handling are not covered by the warranty.
Protect your phone
Always treat your phone and its accessories with care and keep them
in a clean and dust-free place.
Do not expose your phone or its accessories to open flames or lit
tobacco products.
Do not drop, throw or try to bend your phone or its accessories.
Do not use harsh chemicals, cleaning solvents, or aerosols to clean
the device or its accessories.
Do not paint your phone or its accessories.
Do not attempt to disassemble your phone or its accessories, only
authorised personnel must do so.
Store your phone or its accessories at temperatures between 0°C to
40°C.
Please check local regulations for disposal of electronic products.
Do not carry your phone in your back pocket as it could break when
you sit down.
Damage requiring service
Unplug the product from the electrical outlet and refer servicing to an
authorized service technician or provider under the following conditions:
The product has been exposed to rain or liquid, dropped, subject to
impact or damaged.
There are noticeable signs of overheating.
The product does not operate normally when you follow the operating
instructions.
Avoid hot areas
The product should be placed away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat.
Avoid wet areas
Never use the product in rain, or near washbasins or other wet or high
humidity locations. If your product gets wet, do not try to dry the product
with the use of an oven or dryer, as this may damage your product.
Avoid using your device after a dramatic change in temperature
When you move your device between environments with very different
temperature and/or humidity ranges, condensation may form on or
within the device. To avoid damaging the device, allow sufficient time
for the moisture to evaporate before using the device.
NOTICE: When taking the device from low-temperature conditions into
a warmer environment or from high-temperature conditions into a
cooler environment, allow the device to acclimate to room temperature
before turning on power.
Safety and regulatory guide 7
Avoid pushing objects into product
Never push objects of any kind into cabinet slots or other openings in
the product. Slots and openings are provided for ventilation. These
openings must not be blocked or covered.
Adjust the volume
Turn down the volume before using headphones or other audio
devices.
Cleaning
Unplug the product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning, but
NEVER use water to clean the LCD screen.
Small children
Do not leave your phone and its accessories within the reach of small
children or allow them to play with it. They could hurt themselves or
others, or could accidentally damage the phone. Your phone contains
small parts with sharp edges that may cause an injury or which could
become detached and create a choking hazard. Consult the doctor
immediately if the accessories or battery are swallowed.
Repetitive motion injuries
To minimise the risk of RSI, when Texting or playing games with your
phone:
Do not grip the phone too tightly
Press the buttons lightly
Electrostatic discharge (ESD)
Do not t ouch t he SIM c ard’s m etal connectors.
Emergency calls
This phone, like any wireless phone, operates using radio signals,
which cannot guarantee connection in all conditions. Therefore, you
must never rely solely on any wireless phone for emergency
communications.
Regulatory agency identifications
For regulatory identification purposes, your product is assigned a model
number of PM63100.
FCC ID: NM8PM63100.
To ensure continued reliable and safe operation of your device, use only
the accessories listed below with your PM6 3100.
The Battery Pack has been assigned a model number of BM35100.
Operating temperature range: 32°F to 104°F (0°C to 40°C)
NOTE: This product is intended for use with a certified Class 2 Limited
Power Source, rated 5 Volts DC, maximum 1 Amp power supply unit.
8 Safety and regulatory guide
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio or television technician for
help.
FCC Caution: Any changes or modifications not expressly approved by
the part y responsible f or comp liance could v oid the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Operation on the 5.15-5.25 GHz frequency band is restricted to indoor use
only. The FCC requires indoor use for the 5.15-5.25 GHz band to reduce
the potential for harmful interference to co-channel Mobile Satellite
Systems.
FCC Hearing-Aid Compatibility (HAC) Regulations for Wireless
Devices
On July 10, 2003, the U.S. Federal Communications Commission (FCC)
Report and Order in WT Docket 01- 309 modified the exception of
wireless phones under the Hearing Aid Compatibility Act of 1988 (HAC
Act) to require digital wireless phones be compatible with hearing-aids.
The intent of the HAC Act is to ensure reasonable access to
telecommunications services for persons with hearing disabilities. While
some wireless phones are used near some hearing devices (hearing aids
and cochlear implants), users may detect a buzzing, humming, or whining
noise. Some hearing devices are more immune than others to this
interference noise, and phones also vary in the amount of interference
they generate. The wireless telephone industry has developed a rating
Safety and regulatory guide 9
Hearing devices may also be rated. Your
hearing device manufacturer or hearing
health professional may help you find this
rating. Higher ratings mean that the
hearing device is relatively immune to
interference noise.
system for wireless phones, to assist hearing device users find phones
that may be compatible with their hearing devices. Not all phones have
been rated. Phones that are rated have the rating on their box or a label
located on the box. The ratings are not guarantees. Results will vary
dependi ng on the user’s heari ng devi ce and hearin g loss. If your hearing
device happens to be vulnerable to interference, you may not be able to
use a rated phone successfully. Trying out the phone with your hearing
device is the best way to evaluate it for your personal needs.
M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely
to generate less interference to hearing devices than phones that are not
rated. M4 is the better/higher of the two ratings. PM63100 is rated M3.
T-Ratings: Phones rated T3 or T4meet FCC requirements and are likely to
be more usable w ith a hearing aid’s telecoil than pho nes that are not rat ed.
T4 is the better/higher of the two ratings. Your PM63100 is rated T3.
Please power off the Bluetooth function while using hearing aid devices
with your PM63100.
The hearing aid and wireless phone rating values are then added together.
A sum of 5 is considered acceptable for normal use. A sum of 6 is
considered for better use. A sum of 8is considered for best use. In the
above example, if a hearing aid meets the M2 level rating and the wireless
phone meets the M3 level rating, the sum of the two values equal M5. This
should provide the he aring aid user with “n ormal usage ” while using their
hearing aid wit h the particular wireless pho ne. “Nor mal usa ge” in t his
context is defined as a signal quality that is acceptable for normal
operation.
This methodology applies equally for T ratings. The M mark is intended to
be synonymous with the U mark. The T mark is intended to be
synonymous with the UT mark. The M and T marks are recommended by
the Alliance for Telecommunications Industries Solutions (ATIS). The U
and UT marks are referenced in Section 20.19 of the FCC Rules. The
HAC rating and measurement procedure are described in the American
National Standards Institute (ANSI) C63.19 standard.
This phone has been tested and rated for use with hearing aids for some
of the wireless technologies that it uses. However, there may be some
newer wireless technologies used in this phone that have not been tested
yet for use with hearing aids. It is important to try the different features of
10 Safety and regulatory guide
For information about hearing aids and digital wireless phones
FCC Hearing Aid Compatibility and Volume Control:
http://www.fcc.gov/cgb/dro/hearing.html
Gallaudet University, RERC:
https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm
this phone thoroughly and in different locations, using your hearing aid or
cochlear implant, to determine if you hear any interfering noise. Consult
your service provider or the manufacturer of this phone for information on
hearing aid compatibility. If you have questions about return or exchange
policies, consult your service provider or phone retailer.
SAR Information
0.902 W/kg@1g (HEAD)
1.18 W/kg@1g (BODY)
Body-worn Operation
This device was tested for typical body-worn operations. To comply with
RF exposure requirements, a minimum separation distance of 1.0 cm
must b e maintained b etween the us er’s body and t he han dset, including
the antenna. Third-party belt-clips, holsters, and similar accessories used
by this device should not contain any metallic components. Body-worn
accessories that do not meet these requirements may not comply with RF
exposure requirements and should be avoided.
Use only the supplied or an approved antenna. Unauthorized antennas,
modifications, or attachments could impair call quality, damage the phone,
or result in violation of regulations. Do not use the phone with a damaged
antenna. If a damaged antenna comes into contact with the skin, a minor
burn may result. Please contact your local dealer for replacement
antenna.
FCC RF Radiation Exposure Statement
This Transmitter has been demonstrated co-location compliance
requirements with Bluetooth and WLAN.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment.
WEEE notice
The Directive on Waste Electrical and Electronic Equipment (WEEE),
which entered into force as European law on 13th February 2003, resulted
in a major change in the treatment of electrical equipment at end-of-life.
Safety and regulatory guide 11
The WEEE logo (shown at the left) on the product or on its
box indicates that this product must not be disposed of or
dumped with your other household waste. You are liable to
dispose of all your electronic or electrical waste equipment
by relocating over to the specified collection point for
recycling of such hazardous waste. Isolated collection and
proper recovery of your electronic and electrical waste
equipment at the time of disposal will allow us to help
conserving natural resources. Moreover, proper recycling of
the electronic and electrical waste equipment will ensure
safety of human health and environment. For more
information about electronic and electrical waste equipment
disposal, recovery, and collection points, please contact
your local city center, household waste disposal service,
shop from where you purchased the equipment, or
manufacturer of the equipment.
The purpose of this Directive is, as a first priority, the prevention of WEEE,
and in addition, to promote the reuse, recycling and other forms of
recovery of such wastes so as to reduce disposal.
RoHS compliance
This product is in compliance with Directive 2002/95/EC of the European
Parliament and of the Council of 27 January 2003, on the restriction of the
use of certain hazardous substances in electrical and electronic
equipment (RoHS) and its amendments.
htc.com
91H0XXXX-XXM Rev.A
Loading...