HT Simple Touch Programming Instruction

15-Channel Remote Programing Instruction

February 2019

Simple Touch 15-Channel Remote

1

Step 1. 15-Channel Remote Frequency Connection

Back side of remote

Setp 2. Setup Top Limit

Press Up button to move shade to top limited location.

Press Up and My Favorite buttons at the same time for 5 seconds.

You will hear 3 short "B".

Top limit setup completed.

Setp 3. Setup Bottom Limit

Press Down button to move shade to bottom limited location.

Press Down

You will hear 3 short "B".

Bottom limit setup completed.

and My Favorite buttons at the same time for 5 seconds.

Use Left or Right button to select channel from
1 to 15.

Press motor receiver with pin or paper clip for
2 seconds. Wait for motor to "jog".
Click P2 button (on back of remote) with pin

or paper clip, and then wait for motor to "jog".
Click P2 again and wait for another "jog".

Click Up button.

RF connection completed.

Step 4. Setup My Favorite Position

Operate the shade to your favorite position.

Press My Favorite button for 5 seconds. Wait for a short "B".

Then press My Favorite

My Favorite position setup completed.

* Hide unused channels on remote

* Unhide channels on remote

button again for 3 seconds. Wait for 3 short "B".

Press and hold Left and Right buttons at the same time, and then "C" will show on the screen. Wait

until "15" shown on the screen, then release buttons.

Press Left or Right button to select how many channels you want to show on the screen. For

example, if you only have 10 motorized shades connected to this remote, please select "10".

Press and hold My Favorite button (a small "0" will appear first) until channel number shown on

the screen again.

Setting completed.

Press and hold Left and Right buttons at the same time, and then "C" will show on the screen.

Wait until "15"shown on the screen, then release buttons.

Press My Favorite button (a small "0" will appear on screen).

Setting completed.

* Reset/ Re-programing

Press Up, My Favorite, and Down buttons at the same time. Don't release until you hear a long "B".

Start programing

from Step 1 to Step 4 above.

15-Channel Remote Operation Guide

February 2019

Simple Touch 15-Channel Remote

2

❖ Extend and Retract the Shade Before you setup My Favorite Position:

• Press the DOWN button to Extend the Shade.

• Press the UP button to Retract the Shade.

• Press My Favorite button to Stop.

❖ Extend and Retract the Shade After you setup My Favorite Position:

• Press the DOWN button for 1.5 seconds to continuing Extend the Shade.

• Press the UP button for 1.5 seconds to continuing Retract the Shade.

• Press any button to stop

❖ Operate your shade to My Favorite position:

• After you setup My Favorite position, press UP button to retract shade to top limited position.

• Press My Favorite button for 2 seconds to operate shade to your favorite position.

❖ Press LEFT < or RIGHT > button to select the desired channel (Channel 1 - Channel 15). To control 15

motors/ motorized shades synchronously, move to channel “0” for group control.

❖ Add a duplicated remote control:

• Click P2 once on the existing remote, and wait for shade to “jog”. Click P2 again and wait for

another “jog”.

• Click P2 once on the new adding remote, and wait for shade to “jog”.

❖ Disconnect a duplicated remote to the original existing remote:

• Click P2 once on the remote you want to continue use, and wait for shade to “jog”. Click P2 again
and wait for another “jog”.

• Click P2 button once on the remote you want to remove.

❖ Remove All connected remotes:

• Click P2 button once on one of remotes, and wait for shade to “jog”.

• Click My Favorite button, and then wait shade to “jog”.

• Click P2 button on the same remote again, and then shade will jog.

• All remotes will be disconnected.