H S CRAFT GT RGBTX3 User Manual
USE AND CARE INSTRUCTIONS
Oper at e t he R em ote :
CAUTION:
IMPORTANT SAFETY INSTRUCTIONS
• This is an elec trical produc t - not a toy ! To avoid the risk of fire, bur ns, personal injury and electric
• Do not perform any maintenance or troubleshoot for bad or broken lamps
SAVE THESE INSTRUCTIONS
Fig. 1
INSIDE OF COMPARTMENT
Fig. 2
OUTSIDE OF COMPARTMENT
Color Effects® RGB LED 36L G28 String set Model: RGB1-G28-36
When using electrical products, basic precautions should always
be followed including the fol low ing :
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION:
•
To reduce the risk of fire and el ec tr ic shock:
a) Do not install on trees having needles, leaves or branch coverings
of metal or materials which look like metal, and
b) Do not mount or support strings in a manner that can cut or
damage wire insulation.
shock it should not be pl ayed with or placed where small childr en can reach it.
• Do not use season al products outdoors unl ess marked sui table for indoor and outd oor use. Whe n
products are used in outdoor applications, connect the product to a Ground Fault Circuit
Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper
installation.
• Do not use this product for other than its intended use.
•This seasonal use product is not intended for permanent us e or installation.
• Unplug when leaving the house, when retiring for the night, or i f l ef t unattended.
• Do not mount or pl ace near gas or electric h eaters, fir eplaces, c andles or other similar s ources of
heat.
•Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
•Do not hang ornaments or other objects from cord, wire, or light string.
• Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding whi le
the power is on.
while the power is on.
• Do not close doors or wi ndows on the product or extension cords as this may
damage the wire insulation.
• Do not cover the produc t with cloth, paper or any material not part of the product
when in us e.
• This product employs overl oad protection (f use). A blown fuse indicates an overload or sho rt
–circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any
additional strings or pr oducts that may be attac hed to the product, Replace the f use as per
the user servicing i nstructions (follow produc t marking f or proper f use rating) and c heck the
product. If the replacement fuse blows, a short-circuit may be present and the product
should be discarded.
• Do not let lamps rest on the supply cord or on any wire.
• Read and follow all i nstr uctions that are on the product or provided with the product.
• When the product is placed on a live tree, the t ree should be well maintained a nd
fresh. Do not plac e on live trees in whic h the needles are brown or break off easily.
Keep the tree holder filled with water.
• If the product is plac ed on a tree, the tree should be well secured and s table.
• Before using, or reusing, inspect product carefully. Discard any products
that hav e cut , damaged or frayed wire insulation or cords, cracks in the
lampholders or enclosures, loose connections, or exposed copper wire.
•
When storing the product , carefully remove the product from wh erever
it is placed, including trees, branches, or bushes, to avoi d any undue
strain or stress on the product conductors, connecti ons and wires.
• When not in use, store neat l y in a cool, dry location protected from s unlight.
USER SERVICING INSTRUCTIONS:
SAFETY PLUG WITH REPLACEABLE FUSE:
Risk of fire. Do not replace attachment plug. Contains a saf ety device (fuse) that should
not be removed. Disc ard product if the attachment plug is dam aged.
1. Always unplug product from t he receptacle or other outlet device bef ore installing or
replacing fuse.
2. Firmly grasp plug to unplug. Do not unplug by pulling on cord.
3. Open fuse cover. Side open fuse ac cess cover on top of
attachment plug. towards the blades.
4. Remove fuses carefully by turning plug over.
5. Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided wi th product).
6. Side closed the fuse access cover on top of plug.
NOTE:
warranty.
LEDs in thi s se t are non-repl aceable. Tampering with this set will void the
1. Pull out the plastic film from the battery cover to energize the remote. {Fig. 1}
2. The remot e ha s seven buttons {Fig. 2}:
a. ON/OFF – Press to turn the set OFF; press agai n to tur n the set ON.
b. TIMER –- With set on, press ti mer butto n to initiat e 6 hours on / 18 h our s off timer.
c. FUNCTION – Press to change the light patter n to the next mo de.
d. COLOR – Press to change the light color.
NOTE: Ch oo se function then color.
3. The effective operat ing distance of the remote is 33′(10m)
BATTERY CAUTION:
• Always purchas e t he corr ect size a nd gra de of batter y mo st suitabl e f or the inte nded us e.
• Replace o nl y with LR 4 4 butt on batteries.
• Replace all b atteri es of a set at the sam e time.
• Clean the b atter y cont acts an d al so tho se of the de vi ce prior to bat ter y install ation.
• Ensure t he batt eri es are inst all ed corr ectly with regar d to pol arity (+ and -).
• Remov e bat t eries fr om eq uipm ent whi ch is not to be u s ed for an ext e nded p eriod of time.
•Remove us e d batter ies prom ptl y.
1. This lighting string is rated 30 Watts ( 0.25 Amps), do not overload.
Connect ot her lighting s trin gs or dec orat ive out fit s end-to-end up to a m axim um of 21 6 Watt s (1.8
Amps) tota l. If connec ti ng to a L ig hti ng Str in g that do es n ot hav e a Watt age (W ) rat ing, on t he co rd
tag with in 6 inc h es of t he p lug, calculate t he wat tag e as fo llo ws: Mul ti ply t he c ur re nt ( A), wh ich is
also on that cord tag, by 120.
For example: The Lighting String is rated 120V, 60Hz, 0.2Amps. 0.2x 120 = 24Watts.
Add the watt ag e of e ach l ig ht s tri ng t oget he r for a t otal of 216 Watts or less. (D o not exc eed 2 16
Watts.)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
⑴ this device m ay not cause harm ful interference, and
⑵
this device must accept any interference received, including interference that may cause
undesir ed o per at ion.
Modifications not approved by the party responsible for compliance could void user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
＊
Reorient or relocate the receiving antenna.
＊
Increase the separation between the equipment and the receiver.
＊
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
＊
Consult the dealer or an experienced radio/TV technician for help.
For quest i ons and/or assis tance, call c us t o me r s e rv ic e at 1-877-398-7337 or visit us on the web at
www.GEholidaylighting.com
FOR INDOOR AND OUTDOOR USE MADE IN CHINA
PRINTED IN CHINA
©2016 Nicolas Holiday Inc., 9F., No. 37, Guangfu N. Rd Taipei, Taiwan 10560.All rights reserved.
E246482 HC-16
Loading...