H&S XRT Pro Installation & Operation Manual

1-888-628-1730 • XRT Pro Installation Manual 11-888-628-1730 • XRT Pro Installation Manual 1

Rev: 08.21.13

Revision Date

These instructions are current as of 08/21/13. Revisions may apply, and are available at www.hsperformance.com

WARNING!

THIS IS A HIGH PERFORMANCE PRODUCT TO BE USED AT YOUR OWN RISK!

Do not install this product until you have read and fully understand the following disclaimer of liability. The following disclaimer of liability sets forth the terms and conditions for the installation and/or use of this product. By installing this high performance product, the buyer acknowledges that they have read and fully understand this disclaimer and accepts its terms and conditions.

DISCLAIMER OF LIABILITY

H&S Performance, LLC and their successors, distributors, jobbers, dealers, and retailers (SELLER) shall in no way be responsible for any direct, indirect, or consequential damage resulting from improper installation and/or use of this product. The BUYER/USER assumes all responsibility for any damage resulting from the use or misuse of this product The buyer hereby

waives all liability claims for the use of this product.

The BUYER acknowledges that he/she is not relying on the SELLER’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description herein, and the BUYER hereby waives all remedies or liabilities, expressed or implied, arising by law or otherwise, (including without any obligations of the SELLER with respect to tness, merchantability and consequential damages) or whether or not occasioned by the SELLER’s negligence.

The SELLER disclaims any warranty and expressly disclaims any liability for personal injury or damages. The BUYER acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the BUYER agrees to indemnify the SELLER and to hold the SELLER harmless from any claim related to the product purchased. Under no circumstances will the SELLER be liable for any damages or expenses by reason of use or sale of any such products.

The SELLER assumes no liability regarding the improper installation, misuse, or misapplication of its products. It is the buyer and/or installer’s responsibility to check for proper installation.

INTERNET UPDATES:

H&S Performance regularly issues free internet updates and custom tunes for the Mini Maxx. Please check to see if there are any available for your truck by going to the updates section at:

www.hsperformance.com

TROUBLESHOOTING:

Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please call H&S Performance support at 1-888-628-1730

2 XRT Pro Installation Manual • www.hsperformance.com

LIMITATION OF WARRANTY

H&S Performance, LLC (“SELLER”) gives Limited Warranty as to the description, quality, merchantability, tness for any product’s purpose, or any other matter of SELLER’s product sold herewith. The SELLER shall be in no way responsible for the product’s use and service and the BUYER hereby waives all rights other than those expressly written herein. This Warranty shall not be varied except by a written agreement signed and dated by SELLER and BUYER.

The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product’s original packaging. All products that are in question of Warranty must be returned shipping prepaid to the SELLER and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by H&S Performance, LLC.

Under no circumstances shall the SELLER be liable for any labor charges incurred, or travel time incurred in diagnosis for defects, removal, or re-installation of this product, or any other contingent expenses. Any product deemed defective and consequently repaired or replaced by SELLER, shall retain the remainder of the warranty period from date of purchase, as the warranty period shall not be extended due to repair or replacement. Under no circumstances will the SELLER be liable for any damage or expenses incurred by reason of the use or sale of any such product.

-This warranty is null and void after 90 days for an unregistered product. www.hsperformance.com/product-registration/

-This warranty is null and void for any new products purchased through unauthorized dealers. www.hsperformance.com/unauthorized-dealers/

-This warranty is null and void for any products sold as USED or REFURBISHED.

-This warranty is null and void for any products purchased below the H&S UNILATERAL PRICING POLICY www.hsperformance.com/pricing-policies/

-This warranty is null and void for any products that have been altered by a 3rd party.

If the buyer does not agree to the terms of this limited warranty or the disclaimer of liability, the buyer may return this product to the SELLER in a new and unused condition, along with dated proof of purchase, within 30 days of purchase, for a full refund.

To register your product online, visit www.hsperformance.com/register or scan the QR code.

Benets to registering your product include:

• Guarantee full warranty coverage.

• Get entered into drawings for free H&S products and prizes.

• Get notied of software updates and upcoming features.

1-888-628-1730 • XRT Pro Installation Manual 3

TABLE OF CONTENTS

BILL OF MATERIALS ................................................................................................ 5

PARTS DESCRIPTIONS ............................................................................................ 6

XRT PRO OPERATION ............................................................................................. 7

Section 1: Button Navigation ..........................................................................7

Section 2: Install Download ............................................................................. 8

Section 3: Changing Power Levels ..................................................................9

Section 4: Exploring the Menu System ........................................................10

Section 5: Other XRT Pro Features ................................................................11

Diagnostics ...................................................................................................11

Show Settings ..............................................................................................12

T.V.# ................................................................................................................12

Micro SD Card ...............................................................................................12

Web Updates ................................................................................................12

Section 6: USA / ULSD Calibration Vehicle Specic Features ..................13

2006-2007 5.9L Dodge Cummins .............................................................13

2007-2009 6.7L Dodge Cummins .............................................................15

2010-2012 6.7L Dodge Cummins .............................................................18

2003-2007 6.0L Ford Powerstroke ...........................................................20

2008-2010 6.4L Ford Powerstroke ...........................................................21

2011-2014 6.7L Ford Powerstroke ...........................................................23

2007-2010 6.6L LMM Duramax .................................................................25

2011-2014 6.6L LML Duramax ..................................................................26

4 XRT Pro Installation Manual • www.hsperformance.com

BILL OF MATERIALS

The list below includes by name the major parts included in your XRT Pro package.

1. XRT Pro

• Micro SD Card (in XRT Pro)

1.

2.

2. OBDII Adapter Harness

3. USB Adapter

3.

1-888-628-1730 • XRT Pro Installation Manual 5

PARTS DESCRIPTION

This section describes each of the parts in the Bill of Materials, the descriptions provide a physical set of attributes and a purpose for each part. The parts descriptions also list everything that is included in each assembly.

The XRT Pro Head Unit

The main component is the XRT Pro Head Unit. The Head Unit is the interface in which you control vehicle performance parameters. Notice that the head unit has: seven total buttons, ve on the left side and two on the right, a large color screen, and an electronic plug for docking on the back.

Note: XRT Pro includes a micro SD card inserted in the side of the Head Unit.

OBD II Adapter Harness

The OBD II Adapter is a communication hub for the XRT Pro. The OBD ll Adaptor plugs directly into the vehicle OBD ll port and connects to the XRT Pro.

USB to Micro SD Adapter

The USB to Micro SD Adapter is what you will use to update your XRT Pro. You will take the Micro SD card out of the XRT Pro and insert it into the adapter, then insert the adapter into your personal computer.

6 XRT Pro Installation Manual • www.hsperformance.com

XRT PRO OPERATING INSTRUCTIONS

These operating instructions are split into sections:

•SECTION 1: Button Navigation

•SECTION 2: Install Download

•SECTION 3: Changing Power Levels

•SECTION 4: Exploring the Menu System

•SECTION 5: Other XRT Pro Features

•SECTION 6: Vehicle Specic Features

SECTION 1: BUTTON NAVIGATION

Press any of the ve buttons on the left to select items on the screen that are adjacent to the button position.

1-888-628-1730 • XRT Pro Installation Manual 7

In general these buttons work as up and down buttons, they may also be used to select items on the screen adjacent to these buttons.

SECTION 2: INSTALL DOWNLOAD

The Install Download option is used to install tuning onto a vehicle, or return a vehicle to stock.

1. Plug in XRT Pro

2. Select Vehicle to Be Tuned (Tuners can only be installed on ONE vehicle at a time.)

3. Select Install Download: If the vehicle is stock and you enter the install download menu, simply follow the screen prompts to install a download on the vehicle. This is the point in which you may come across the tire size calibration menu, and the vehicle speed limiter menu.

XRT PRO

Change Vehicle

Install Download

Special Functions

Tire Size Calibration

Diagnostics

Show Settings

Update Firmware

Before installing the download:

•MakesurethattheXRTProisproperlypluggedin.

•Makesurethattheharnessisproperlyinstalled.

•Thevehiclebatteryisfullycharged.

•Thevehicleiswarmeduptooperatingtemperature.

THE MICRO SD CARD MUST BE INSERTED IN THE SIDE OF THE XRT PRO

TO DOWNLOAD TO A VEHICLE.

8 XRT Pro Installation Manual • www.hsperformance.com

SECTION 3: CHANGING POWER LEVELS

Dodge Vehicles:

Select “Change Power Level” from the main menu and follow the on-screen prompts. You will get to a screen as pictured below with two options.

Ford and GM vehicles:

Select “Change Power Level” from the main screen. Follow the on-screen prompts to change your power level, this should only take a few seconds. To return to stock, select “Install download” from the main screen. Select “Return to Stock” when prompted to return to factory settings and unlock the XRT Pro from the truck.

Go Back

(RESET)

Download H&S Tuning

Import/Export MCC Tuning

Return to Stock (OEM Tune)

DOWNLOAD MENU

Change Settings: This will install the new tuning onto the truck, for times when your H&S Product has been updated on the H&S website. This is also how you can adjust the speed limiter, tire size, and other options. Return to Stock: This function will completely return your truck’s computer to stock. This is required to unlock the XRT Pro from the vehicle. (Tuners can only be installed on ONE vehicle at a time.)

1-888-628-1730 • XRT Pro Installation Manual 9

SECTION 4: EXPLORING THE MENU SYSTEM

The diagram below shows all of the Main Menu items and explains the Main Menu navigation.

Navigation through the main menu: Use the large Up Down Buttons to page up and page down through all the Main Menu options.

XRT PRO

Change Vehicle

Install Download

Special Functions

Tire Size Calibration

Diagnostics

Show Settings

Update Firmware

These buttons are used to enter into the sub menus from the main menu and may also be used to select additional items when in the sub menus.

10 XRT Pro Installation Manual • www.hsperformance.com

SECTION 5: OTHER XRT PRO FEATURES

DIAGNOSTICS

This functions allows you to check vehicle diagnostics codes. Some models you will have an option to check Engine or Transmission diagnostics. Please select the desired module. Upon entering this menu, the XRT Pro will automatically begin to check the vehicle for DTCs and it will then display those DTCs on the XRT Pro screen. Once it displays the DTCs value and description on the screen it will allow you to erase the DTCs from the vehicle.

DTC

Diagnostic Trouble Codes

Establishing communication

with the vehicle

If no DTCs are displayed you can simply press the Go Back button to return to the main menu. For a complete list of DTC descriptions, please visit the Tech section of our website www.hsperformance.com

Go Back

DTC

to Main Menu

There are no DTCs Detected

Diagnostic Trouble Codes

THE MICRO SD CARD MUST BE INSERTED IN THE SIDE OF THE XRT PRO TO READ AND ERASE DTCS

1-888-628-1730 • XRT Pro Installation Manual 11

SHOW SETTINGS

The Show Settings menu will allow you to see Vehicle Information and System Information.

Go Back

to Main Menu

Vehicle: 08–10 Ford 6.4L VIN: 123456789101112131415 ECM P/N: TCM P/N:

Serial#: N/A MEM–C216 HW–1.3b Version: SW–1.03.0 TV–6.4.20

6.4 Power Stroke

Tune Status: Installed

Application:

SETTINGS

’08-’10 Ford 6.4L PowerStroke

T.V. #

This number is the Tuning Version. It will change as H&S updates the tuner software. To see the latest tuner version on your XRT Pro go to “Show Settings” and scroll down.

MICRO SD CARD

The Micro SD card should only be taken out of the XRT Pro to perform internet upgrades. It is the primary means of performing internet upgrades for the XRT Pro.

In case a Micro SD Card is lost or broken, a new Micro SD Card can be purchased from H&S Performance.

WEB UPDATES

Remove the Micro SD from your XRT Pro. Connect your Micro SD to your personal computer with the included Micro SD to USB adapter to install software updates. Visit www.hsperformance.com in the downloads section for product updates. Please nd your product application and follow the posted instructions there to update your XRT Pro.

12 XRT Pro Installation Manual • www.hsperformance.com

SECTION 6: USA / ULSD CALIBRATION VEHICLE SPECIFIC FEATURES

2006  2007 5.9L DODGE CUMMINS USA / ULSD CALIBRATION

Power Levels

Power Levels can be adjusted on-the-y at the touch of a button after Installing the Download to the vehicle. To adjust the Power Level, select Change Power Level from the Main Menu.

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom downloads may result in dierent ratings and can be found at www.hsperformance.com/update-instructions.

Low Boost Fueling

This option allows for adjustment of the amount of fuel injected under low boost conditions. There are 5 dierent settings for Low Boost Fueling:

0 - Lowest Fueling (Default) 1 - Low Fueling 2 - Medium Fueling 3 - Moderate Fueling 4 - High Fueling

NOTE: The low boost fueling adjustment will aect ALL power levels. This option can only be adjusted during the

Install Download process.

POWER LEVELS

Stock .................... 0 HP

Tow

.................... 60 HP

Street

............... 120 HP

Performance

... 200 HP

Injection Timing

This option allows for the adjustment of the maximum allowed injection timing. There are 5 dierent settings for the Injection Timing:

0 - 18 degrees 1 - 24 degrees 2 - 26 degrees (Default) 3 - 28 degrees 4 - 32 degrees

NOTE: The injection timing adjustment will aect ALL power levels. This option can only be adjusted during the

Install Download process.

Speed Limiter

This option allows for the adjustment of the factory speed limiter. Most 5.9L Cummins trucks have a 106 MPH speed limiter from the factory. The limiter can be adjusted from 50 MPH to 200 MPH. This

option can only be adjusted during the Install Download process.

1-888-628-1730 • XRT Pro Installation Manual 13

2006 - 2007 5.9L Dodge Cummins Specic Features Continued >>

Rev Limiter

This option allows for the adjustment of the factory rev limiter. Most 5.9L Cummins trucks have a 3500 RPM rev limiter from the factory. The limiter can be adjusted from 3000 RPM to 5000 RPM. This

option can only be adjusted during the Install Download process.

Torque Management (Automatic Transmission Only)

This option allows for the disabling of the vehicles torque management for those equipped with automatic transmissions. This is recommend for those running standalone aftermarket TCM/transmission packages but will also slightly improve throttle response on a stock truck.

NOTE: By turning the torque management OFF, the PRNDL display will be lost.

Tire Size Calibration

This option allows for the re-calibration of the factory speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while entering a smaller tire size will cause the factory speedometer to read lower. The tire size can be adjusted from 24” to 42”. This option only takes a few seconds to change and can be adjusted at any time from the Tire Size Calibration menu.

Overdrive Transmission Software

Did you know that your H&S tuning device also has the capability of tuning your transmission? If your 5.9L Cummins is equipped with the 48RFE automatic transmission, you may want to check out our Overdrive Transmission Software. Custom tailored to mate with H&S engine tuning, the 5.9L Overdrive software includes modied torque converter lock/unlock strategies that will command the TC to lock in 3rd gear under wide open throttle and hold it locked through 4th gear. Light throttle torque converter strategies have also been changed to lock-up sooner, keeping more power directed to the road instead of wasted in heat and friction. Shift points are modied to take advantage of the available horsepower and torque output. On a 2006 Cummins with a stock 48RFE, we have seen 0.2 to 0.3 second quicker 1/4 mile times JUST from the addition of the H&S Overdrive tuning! An additional unlock fee may apply, see www.hsperformance.com for details.

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

14 XRT Pro Installation Manual • www.hsperformance.com

2007  2009 6.7L DODGE CUMMINS USA / ULSD CALIBRATION

Power Levels

To adjust the Power Level, select Change Power Level from the Main Menu and follow the on-screen instructions.

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom downloads may result in dierent ratings and can be found at www.hsperformance.com/update-instructions.

Low Boost Fueling

This option allows for the selection of low boost fueling during the download process.

High Rail Pressure

This option allows for the selection of higher rail pressure during the download process.

2 levels:

1 – 26,100 PSI (Default)

2 – 27,500 PSI

Speed Limiter

This option allows for the adjustment of the factory speed limiter. Most 6.7L Cummins trucks have a 106 MPH speed limiter from the factory. The limiter can be adjusted from 20 MPH to 200 MPH. This option can only be adjusted during the Install Download process.

POWER LEVELS

Stock .................... 0 HP

Tow

.................... 40 HP

Street

................. 80 HP

Performance

.... 120 HP

Tire Size Calibration

This option allows for the re-calibration of the factory speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while entering a smaller tire size will cause the factory speedometer to read lower. The tire size can be adjusted from 25.5” to 45”. This option only takes a few seconds to change and can be adjusted at any time from the Tire Pressure Calibration menu.

Special Functions / Features

Your H&S tuning device has the capability of Enabling / Disabling factory vehicle features. These features can be found in the Special Functions Menu. Below is a short description of each feature:

NOTE: If any special feature is already listed as Enabled but is not functioning correctly, you may need to disable the

feature, cycle the key, and re-enable the feature to make it function properly. If it still does not work, your vehicle

may not be equipped with the hardware required for the special feature. The previous selection will NOT be

saved. If the Special Functions/Features Menu is exited and returned into, it will not display your previous selection. This is normal and the Enable/Disable function is still working properly.

1-888-628-1730 • XRT Pro Installation Manual 15

2007 - 2009 6.7L Dodge Cummins Specic Features Continued >>

TPMS: Enable / Disable the Tire Pressure Monitoring System.

Optical Chirp on Lock: Enable / Disable the parking lights ashing when locking the vehicle.

Horn Chirp on Lock: Enable / Disable the horn chirp when locking the vehicle.

Set Head Lamp Delay: Enable / Disable the head lamp delay.

Accessory Delay: Enable / Disable the shut-o delay of your radio and accessory system after the key has

been turned o.

Fog Lights W/High: Enable / Disable the fog lights staying on when high beams are being used.

Daytime Lights: Enable / Disable the daytime running lights.

Seat Belt Minder: Enable / Disable the chime for the drivers seat belt system. This feature will not dis-

able the seat belt light.

Auto Door Lock: Enable / Disable the automatic door locking when the vehicle reaches certain speeds.

Unlock Driver Door: Enable / Disable unlocking only the driver door when pushing the unlock button

the key-fob. When enabled, the unlock button on the key fob will need to be pressed twice in order to unlock all doors.

Idle Up (Auto Only): Enable / Disable the use of the cruise control buttons to control idle RPM. Follow your vehicle owners manual to use this feature

Overdrive Transmission Software

Did you know that your H&S tuning device also has the capability of tuning your transmission? If your 6.7L Cummins is equipped with the 68RFE automatic transmission, you may want to check out our Overdrive Transmission Software. Custom tailored to mate with H&S engine tuning, the

6.7L Overdrive software includes boosted line pressures, modied full and part throttle torque converter lock/unlock strategies, adjusted full and part throttle shift points, adjusted full and part throttle shift rmness, modied torque management tables, and much more! All changes are designed to keep more power directed to the road instead of wasted in heat and friction. On our test trucks, we have seen 0.2 to 0.3 second quicker 1/4 mile times JUST from the addition of the H&S Overdrive tuning! An additional unlock fee may apply, see www.hsperformance.com for details.

Overdrive Tuning Options

4-5th gear shift point adjustable up or down. Light to medium throttle, WOT is NOT adjustable.

5 levels:

1 – Lowest 2 – Stock shift point 3 – Medium 4 – Default 5 – Highest

16 XRT Pro Installation Manual • www.hsperformance.com

5-6th gear shift point adjustable up or down. Light to medium throttle, WOT is NOT adjustable.

5 levels:

1 – Lowest 2 – Stock shift point 3 – Medium 4 – Default 5 – Highest

Line pressure. WARNING, only designed for built transmissions. The factory transmission pump is NOT designed to be run more than 165-170 psi of pressure. Our current overdrive tune sets these values to 170psi (the pump mechanically will not supply more pressure, and will build excess heat and waste energy). If they have a modied pump, they can use this adjustment to increase clutch holding pressure. We have tested up to 250 psi with great results.

5 levels:

1 – Stock 160 psi 2 – Default 170 psi 3 – 200 psi 4 – 225 psi 5 – 250 psi

Shift Firmness. This adjustment will modify the acceleration rate between gear shifts. Making them softer or rmer.

5 levels:

1 – Stock 2 – Light rm 3 – Default 4 – Firm 5 – Most rm

NOTE:

An additional unlock fee may apply, click here for details.

*Overdrive Transmission Software is not available on Cab & Chassis models.

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

1-888-628-1730 • XRT Pro Installation Manual 17

2010  2012 6.7L DODGE CUMMINS USA / ULSD CALIBRATION

Power Levels

To adjust the Power Level, select Change Power Level from the Main Menu and follow the on-screen instructions.

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom downloads may result in dierent ratings and can be found at www.hsperformance.com/update-instructions.

Speed Limiter

This option allows for the adjustment of the factory speed limiter. Most 2010 - 2012 6.7L Cummins trucks have a 106 MPH speed limiter from the factory. The limiter can be adjusted from 20 MPH to 200 MPH. This option can only be adjusted during the Install

Download process.

Torque Management (Manual Transmission Only)

This option allows for the disabling of the vehicles torque management for those equipped with manual transmissions. This option increases pedal sensitivity and throttle response when REMOVED.

Tire Size Calibration

This option allows for the re-calibration of the factory speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while entering a smaller tire size will cause the factory speedometer to read lower. The tire size can be adjusted from 25.5” to 45”. This option can only be seen/changed after the Download is Installed to the vehicle. This option only takes a few

seconds to change and can be adjusted at any time from the Tire Size Calibration menu.

20102012 PICKUP

POWER LEVELS

Tow .................... 40 HP

Street

................. 80 HP

2011 CAB & CHASSIS

POWER LEVELS

Tow .................... 20 HP

Street

................. 40 HP

Special Functions / Features

Your H&S tuning device has the capability of Enabling / Disabling factory vehicle features. These features can be found in the Special Functions Menu. These features can only be seen/changed after

the Download is Installed to the vehicle. Below is a short description of each feature:

TPMS: Enable / Disable the Tire Pressure Monitoring System.

Optical Chirp on Lock: Enable / Disable the parking lights ashing when locking the vehicle.

Horn Chirp on Lock: Enable / Disable the horn chirp when locking the vehicle.

Set Head Lamp Delay: Enable / Disable the head lamp delay.

Accessory Delay: Enable / Disable the shut-o delay of your radio and accessory system after the key has

been turned o.

18 XRT Pro Installation Manual • www.hsperformance.com

Fog Lights W/High: Enable / Disable the fog lights staying on when high beams are being used.

Daytime Lights: Enable / Disable the daytime running lights.

Seat Belt Minder: Enable / Disable the chime for the drivers seat belt system. This feature will not dis-

able the seat belt light.

NOTE: If any special feature is already listed as Enabled but is not functioning correctly, you may need to disable the

feature, cycle the key, and re-enable the feature to make it function properly. If it still does not work, your vehicle may

not be equipped with the hardware required for the special feature.

Stationary Idle Adjust:

The Stationary Idle Adjust Menu will allow you to adjust the idle speed of your vehicle while in Park or Neutral using your H&S tuning device. Choose the desired idle speed and select Set to set the idle speed to the chosen RPM. Idle speed can be adjusted from 700 RPM to 1500 RPM.

Overdrive Transmission Software

Did you know that your H&S tuning device also has the capability of tuning your transmission? If your 6.7L Cummins is equipped with the 68RFE Automatic Transmission, you may want to check out our Overdrive Transmission Software. Custom tailored to mate with H&S engine tuning, the 6.7L Overdrive software includes boosted line pressures, modied full and part throttle torque converter lock/unlock strategies, adjusted full and part throttle shift points, adjusted full and part throttle shift rmness, modied torque management tables, and much more! All changes are designed to keep more power directed to the road instead of wasted in heat and friction. On our test trucks, we have seen 0.2 to 0.3 second quicker 1/4 mile times JUST from the addition of the H&S Overdrive tuning! An additional unlock fee may apply, see www.hsperformance.com for details.

Overdrive Tuning Options

Line pressure. WARNING, only designed for built transmissions. The factory transmission pump is NOT designed to be run more than 165-170 psi of pressure. Our current overdrive tune sets these values to 170 psi (the pump mechanically will not supply more pressure, and will build excess heat and waste energy). If they have a modied pump, they can use this adjustment to increase clutch holding pressure. We have tested up to 250 psi with great results.

5 levels:

1 – Stock 160 psi 2 – Default 170 psi 3 – 200 psi 4 – 225 psi 5 – 250 psi

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a

1-888-628-1730 • XRT Pro Installation Manual 19

2010 - 2012 6.7L Dodge Cummins Specic Features Continued >>

custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

2003  2007 6.0L FORD POWERSTROKE USA / ULSD CALIBRATION

Power Levels

Power Levels can be adjusted on-the-y at the touch of a button after Installing the Download to the vehicle. To adjust the Power Level, select Change Power Level from the Main Menu.

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom downloads may result in dierent rat-

ings and can be found at www.hsperformance.com/update-instructions.

Speed Limiter

This option allows for the removal of the factory speed limiter. Most 6.0L Powerstroke trucks have a 95 MPH speed limiter from the factory. The limiter can be removed completely or left stock (this may change so be sure to visit www.hsperformance.com for product updates). This option can only be changed during the Install Download process.

POWER LEVELS

Stock .................... 0 HP

Tow

.................... 40 HP

Street

................. 80 HP

Performance

... 120 HP

Tire Size Calibration

(Not currently available for the 2003 - 2007 6.0L Powerstroke. This may change so be sure to visit www.hsperformance.com for product updates) This option allows for the re-calibration of the factory

speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while en-

tering a smaller tire size will cause the factory speedometer to read lower.

Tire size can be adjusted

from 25” to 40”. This option can only be adjusted during the Install Download process.

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

20 XRT Pro Installation Manual • www.hsperformance.com

2008  2010 6.4L FORD POWERSTROKE USA / ULSD CALIBRATION

Power Levels

Power Levels can be adjusted on-the-y at the touch of a button after Installing the Download to the vehicle. To adjust the Power Level, select Change Power Level from the Main Menu.

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom downloads may result in dierent rat-

ings and can be found at www.hsperformance.com/update-instructions.

Speed Limiter

This option allows for the adjustment of the factory speed limiter. Most 6.4L Powerstroke trucks have a 95 MPH speed limiter from the factory. The limiter can be adjusted from 55 MPH to 200 MPH. This option can only be adjusted during the Install Download process.

Tire Size Calibration

This option allows for the re-calibration of the factory speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while entering a smaller tire size will cause the factory speedometer to read lower. The tire size can be adjusted from 25” to 45”. This option can only be adjusted during the Install Download process.

POWER LEVELS

Stock .................... 0 HP

Tow

.................... 40 HP

Street

................. 80 HP

Performance

.... 120 HP

Shift Schedule

This option allows you to change the shift logic of your automatic transmission. There are 2 options. To change these options, you must repeat the install download process.

1. Schedule 1: This option will lock the torque converter in 4th gear under normal driving, and keep it locked through 5th gear.

2. Schedule 2: This option will not lock the torque converter until 5th gear under normal driving.

NOTE: The Easy Power Tuning also has Easy shift schedule. It is NOT adjustable.

Shift Point

This option will allow you to modify shift points for the 3-4 and 4-5 shifts. There are 3 options to choose from. To change these options, you must repeat the install download process.

1. Low: This option will shift into high gears at the lowest possible road speed.

2. Med: This option is the middle range of shift points

3. High: This option will shift into high gears at the highest possible road speed.

1-888-628-1730 • XRT Pro Installation Manual 21

2008 - 2010 6.4L Ford Powerstroke Specic Features Continued >>

TPMS Adjustability / Disable

Many 2008 - 2010 6.4L Powerstrokes are equipped with a TPMS or Tire Pressure Monitoring System from the factory. This system is designed to alert the driver of a problem with the vehicles tire pressures but is often a nagging inconvenience for those individuals wanting to run lower pressures or get rid of the TPMS sensors altogether.

H&S Performance has a designed solution for those individuals. By using your H&S tuning device and a 6.4L Powerstroke TPMS Adapter (Part #709913), you will have full control of the TPMS. Front and rear tire pressures will be independently adjustable from 0 - 100 PSI as well as the option to Disable the TPMS completely if removing the TPMS sensors from the vehicle. All changes to the TPMS must be done with the 6.4L Powerstroke TPMS Adapter in place and the Adapter must be removed after changes are made to resume normal tuner function.

Transmission Relearn

The 5R110 automatic transmission on the 2008 - 2010 6.4L Powerstroke has what is called Adaptive Memory and is constantly learning and adapting to dierent horsepower levels, temperatures, driving habits, etc. After completing the Install Download process on the 6.4L Powerstroke, the Transmission Adaptive Memory is automatically reset. We highly recommend performing a Transmission Relearn procedure after installing H&S tuning to help the transmission perform correctly with the added horsepower. The 5R110 automatic transmission will eventually learn over time on its own, but the relearn procedure gives a good baseline for the adaptive learning and helps to speed up the learning process. To perform the relearn procedure, please follow these instructions:

When re-training the transmission, ALWAYS follow posted speed limits. Do NOT attempt runs in adverse weather conditions such as snow, ice, rain, wind, or any other conditions that may aect your vehicles traction or impair your visibility!

1. After H&S tuning is installed, perform each of the following 0-80 MPH runs while in the Performance power level. During this relearn process, you may experience hesitation during shifts, hard shifts, or defuel patterns, all of which are normal:

• 0-80 MPH @ 25% throttle position, then slow down and come to a complete stop.

• 0-80 MPH @ 50% throttle position, then slow down and come to a complete stop.

• 0-80 MPH @ 100% throttle position, then slow down and come to a complete stop.

The Transmission Relearn procedure is complete.

NOTE: On any vehicle using 3” or larger lift blocks under the rear leaf pack, it is HIGHLY RECOMMENDED to install

traction bars. With any added horsepower, failure to do so may result in harsh shifting and may cause premature transmission and/or driveline damage.

22 XRT Pro Installation Manual • www.hsperformance.com

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

20112014 6.7L FORD POWERSTROKE USA / ULSD CALIBRATION

Power Levels

To adjust the Power Level, select Change Power Level from the Main Menu and follow the on-screen instructions.

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom downloads may result in dierent rat-

ings and can be found at www.hsperformance.com/update-instructions.

Speed Limiter

This option allows for the adjustment of the factory speed limiter. Most 6.7L Powerstroke trucks have a 98 MPH speed limiter from the factory. The limiter can be adjusted from 55 MPH to 200 MPH. This option can only be changed during the Install Download process.

POWER LEVELS

Stock .................... 0 HP

Tow

.................... 40 HP

Street

................. 80 HP

Performance

.... 120 HP

Tire Size Calibration

This option allows for the re-calibration of the factory speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while entering a smaller tire size will cause the factory speedometer to read lower. The tire size can be adjusted from 31” to 34” (this may change so be sure to visit www.hsperformance.com for product updates). This option only takes a few seconds to change and can be adjusted at any time from the Tire Size Calibration menu.

TPMS Adjustability / Disable

Many 2011 - 2014 6.7L Powerstrokes are equipped with a TPMS or Tire Pressure Monitoring System from the factory. This system is designed to alert the driver of a problem with the vehicles tire pressures but is often a nagging inconvenience for those individuals wanting to run lower pressures or get rid of the TPMS sensors altogether.

1-888-628-1730 • XRT Pro Installation Manual 23

2011 - 2012 6.7L Ford Powerstroke Specic Features Continued >>

With your H&S tuning device, you have full control of the TPMS. Front and rear tire pressures are independently adjustable from 0-120 PSI as well as the option to disable the TPMS completely if removing the TPMS sensors from the vehicle. This option only takes a few seconds to change and can be adjusted at any time from the Tire Pressure Calibration menu.

NOTE: TPMS adjustments will not take full eect on a stationary vehicle. Once adjustments have been made, it can

take up to 5 miles of driving before changes take eect.

Transmission Tuning

Did you know that your H&S tuning device also has the capability of tuning your transmission? Our transmission tuning for the 6R140 automatic transmission is custom tailored to mate with H&S engine tuning. Some features include: boosted line pressures, modied full and part throttle lock/unlock strategies, adjusted full and part throttle shift points, adjusted full and part throttle shift rmness, and modied torque management tables. All changes are designed to keep more power directed to the road instead of wasted in heat and friction. On our test trucks, we have seen 0.2 to 0.3 second quicker 1/4 mile times JUST from the addition of H&S transmission tuning! An additional unlock fee may apply, see www.hsperformance.com for details.

Transmission Relearn

The 6R140 automatic transmission on the 2011 - 2014 6.7L Powerstroke has what is called Adaptive Memory and is constantly learning and adapting to dierent horsepower levels, temperatures, driving habits, etc. If you selected to tune the transmission during the Install Download process, the Transmission Adaptive Memory is automatically reset when the download completes. We highly recommend performing a Transmission Relearn procedure after installing H&S transmission tuning to help the transmission perform correctly with the added horsepower. The 6R140 automatic transmission will eventually learn over time on its own, but the relearn procedure gives a good baseline for the adaptive learning and helps to speed up the learning process. To perform the relearn procedure, please follow these instructions:

When re-training the transmission, ALWAYS follow posted speed limits. Do NOT attempt runs in adverse weather conditions such as snow, ice, rain, wind, or any other conditions that may aect your vehicles traction or impair your visibility!

1. After H&S tuning is installed, perform each of the following 0-80 MPH runs while in the Performance power level. During this relearn process, you may experience hesitation

during shifts, hard shifts, or defuel patterns, all of which are normal:

• 0-80 MPH @ 25% throttle position, then slow down and come to a complete stop.

24 XRT Pro Installation Manual • www.hsperformance.com

• 0-80 MPH @ 50% throttle position, then slow down and come to a complete stop.

• 0-80 MPH @ 100% throttle position, then slow down and come to a complete stop.

The Transmission Relearn procedure is complete.

NOTE: On any vehicle using 3” or larger lift blocks under the rear leaf pack, it is HIGHLY RECOMMENDED to install

traction bars when adding additional horsepower.

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

20072010 6.6L LMM DURAMAX USA / ULSD CALIBRATION

Power Levels

Power Levels can be adjusted on-the-y at the touch of a button after Installing the Download to the vehicle. To adjust the Power Level, select Change Power Level from the Main Menu.

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom downloads may result in dierent rat-

ings and can be found at www.hsperformance.com/update-instructions.

POWER LEVELS

Stock .................... 0 HP

Tow

.................... 40 HP

Street

................. 80 HP

Performance

.... 120 HP

Speed Limiter

This option allows for the adjustment of the factory speed limiter. Most 6.6L LMM Duramax trucks have a 98 MPH speed limiter from the factory. The limiter can be adjusted from 50 MPH to 95 MPH or removed completely. This option can only be adjusted during the Install Download process.

Tire Size Calibration

This option allows for the re-calibration of the factory speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while entering a smaller tire size will cause the factory speedometer to read lower. The tire size can be adjust-

1-888-628-1730 • XRT Pro Installation Manual 25

2007 - 2010 6.6L LMM Duramax Specic Features Continued >>

ed from 25” to 60”. This option can only be adjusted during the Install Download process.

NOTE: On some vehicles, entering a tire size larger than 35” may cause the ABS light to illuminate.

Transmission Reset / Relearn

The automatic transmission on the 2007 - 2010 6.6L LMM Duramax has what is called Adaptive Memory and is constantly learning and adapting to dierent horsepower levels, temperatures, driving habits, etc. We highly recommend performing a Transmission Reset / Relearn procedure after installing H&S tuning to help the transmission perform correctly with the added horsepower. The transmission will eventually learn over time on its own, but the relearn procedure gives a good baseline for the adaptive learning and helps to speed up the learning process. To perform the relearn procedure, please follow these instructions:

When re-training the transmission, ALWAYS follow posted speed limits. Do NOT attempt runs in adverse weather conditions such as snow, ice, rain, wind, or any other conditions that may aect your vehicles traction or impair your visibility!

1. After you have installed the H&S tuning, turn the key to the ON position. From the Main Menu, scroll down until you see the Reset Transmission option. Select Reset Trans- mission and follow the on-screen instructions to reset the transmission adaptive memory.

2. After the transmission reset is complete, it is recommended to perform each of the following 0-80 MPH runs while in the Performance power level:

• 0-80 MPH @ 25% throttle position, then slow down and come to a complete stop.

• 0-80 MPH @ 50% throttle position, then slow down and come to a complete stop.

• 0-80 MPH @ 100% throttle position, then slow down and come to a complete stop.

The Transmission Relearn procedure is complete.

NOTE: On any vehicle using 3” or larger lift blocks under the rear leaf pack, it is HIGHLY RECOMMENDED to install

traction bars when adding additional horsepower.

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

26 XRT Pro Installation Manual • www.hsperformance.com

20112014 6.6L LML DURAMAX USA / ULSD CALIBRATION

Power Levels

Power levels are not currently shift-on-the-y for the 2011 - 2014 6.6L LML Duramax. To adjust the Power Level, select Change Power Level from the Main Menu and follow the on-screen instructions (this may change so be sure to visit

www.hsperformance.com for product updates).

NOTE: The Power Level ratings listed may not be exact for your particular

vehicle. The listed ratings apply to the out-of-the-box tuning that H&S tuning devices are shipped with. Any custom

downloads may result in dierent ratings and can be found at www.hsperformance.com/update-instructions.

Speed Limiter

This option allows for the removal of the factory speed limiter. Most 6.6L LML Duramax trucks have a 98 MPH speed limiter from the factory. This option can only be changed during the Install Download process.

Tire Size Calibration

This option allows for the re-calibration of the factory speedometer to adjust for non-stock sized tires. For the most accurate speedometer reading when using non-stock sized tires, it is best to measure the diameter of the tire using a tape measure rather than going by the printed tire size. In addition, using a GPS is a great way to dial in your factory speedometer. Entering a larger tire size will cause the factory speedometer to read higher while entering a smaller tire size will cause the factory speedometer to read lower. The tire size can be adjusted from 25” to 60”. This option can only be adjusted during the Install Download process.

POWER LEVELS

Tow .................... 40 HP

Street

................. 80 HP

NOTE: On some vehicles, entering a tire size larger than 35” may cause the ABS light to illuminate.

Transmission Reset / Relearn

The automatic transmission on the 2011 - 2014 6.6L LML Duramax has what is called Adaptive Memory and is constantly learning and adapting to dierent horsepower levels, temperatures, driving habits, etc. We highly recommend performing a Transmission Reset / Relearn procedure after installing H&S tuning to help the transmission perform correctly with the added horsepower. The transmission will eventually learn over time on its own, but the relearn procedure gives a good baseline for the adaptive learning and helps to speed up the learning process. To perform the relearn procedure, please follow these instructions:

When re-training the transmission, ALWAYS follow posted speed limits. Do NOT attempt runs in adverse weather conditions such as snow, ice, rain, wind, or any other conditions that may aect your vehicles traction or impair your visibility!

1. After you have installed the H&S tuning, turn the key to the ON position. From the Main

1-888-628-1730 • XRT Pro Installation Manual 27

20011 - 2014 6.6L LML Duramax Specic Features Continued >>

Menu, scroll down until you see the Reset Transmission option. Select Reset Transmis- sion and follow the on-screen instructions to reset the transmission adaptive memory.

2. After the transmission reset is complete, it is recommended to perform each of the following 0-80 MPH runs while in the Performance power level:

• 0-80 MPH @ 25% throttle position, then slow down and come to a complete stop.

• 0-80 MPH @ 50% throttle position, then slow down and come to a complete stop.

• 0-80 MPH @ 100% throttle position, then slow down and come to a complete stop.

The Transmission Relearn procedure is complete.

NOTE: On any vehicle using 3” or larger lift blocks under the rear leaf pack, it is HIGHLY RECOMMENDED to install

traction bars when adding additional horsepower.

Gear Ratio Adjustability

During the download process you have the option to calibrate your gear ratio. You have four choices; 3.54, 3.73, 4.10, and 4.54.

Dual Fuel Tank Option

During the download process you have the option to choose whether or not your truck is equipped with dual fuel tanks

Maxx Calibration Control

Maxx Calibration Control (MCC) is an advanced engine management software tool that enables custom tune editing with your H&S tuning device. With the power to control all aspects of engine and transmission management, MCC gives YOU the ability to control how YOUR engine operates! When you have exceeded the limits of conventional tuning and want to unleash the power of a custom tune, look no further than MAXX CALIBRATION CONTROL

NOTE: Applications may vary by vehicle make and model, please check our website to see if MCC is available for your

vehicle at www.hsperformance.com/mcc

28 XRT Pro Installation Manual • www.hsperformance.com

1-888-628-1730 • XRT Pro Installation Manual 29

30 XRT Pro Installation Manual • www.hsperformance.com

1-888-628-1730 • XRT Pro Installation Manual 31

32 XRT Pro Installation Manual • www.hsperformance.com