1
About your Slimline Digital Timer
2
Mechanism Dimensions
Digital Timer
Cat D817SLIM
Instruction Manual
This 7 day digital timer can be set with up to 16
programs. Each of these can be set to repeat
daily, weekly, daily during the working week,
daily on weekends and in a variety of other day
combinations to maximise flexibility.
Additionally this timer has a Random Feature and
Countdown Mode.
This timer has an internal rechargeable battery
to keep your settings in the event of a power
failure. When new, or not used for some time,
the battery may need recharging before you can
setup your timer. Plug the timer in for a few
hours or overnight to recharge the battery.
42mm
25mm
44mm
12mm
118mm
http://waterheatertimer.org/Woods-timers-and-manuals-old.html#HPM
3
Operation
HPM recommends you keep these instructions for
future reference.
Setting a digital timer can be confusing at first.
Essentially there are 3 steps:
1. Set the clock.
2. Setup your switching programs.
3. Put in AUTO mode and plug in your device.
The timer has 3 modes. Press the MENU button to
change from one mode to the next.
To return to clock mode from Program Setting Mode, press MENU twice.
To return to clock mode from Countdown Mode, press MENU once.
1. Clock Mode –
The screen will display
the current time and day.
2. Program Mode –
Enables you to scroll
through to view or set
the 16 program settings.
3. Countdown Mode –
Enables you to simply
set the timer to turn ON
or OFF at a later time.
MENU
UP
RCL
OK
DOWN
RESET
15:43
WE
P
1
ON
10:59
25
WE
AUTO
OFF
+1h
0:00
00
AUTO
OFF
OTD
+1h
A
Clock Mode - Setting the Clock
B
Program Mode – Navigating Program Mode
(i) Is it Standard or Daylight Savings Time? In
Clock Mode press RCL to change to Summer
Time – the display will show +1h. Press RCL
again to return to Standard time.
(ii) Press and hold OK until the days of the week
at the top of the display flash.
(iii) Use the UP and DOWN buttons to set the day
of the week.
(iv) Press OK to confirm – the hour display will flash.
(v) Use the UP and DOWN buttons to set the
current hour (in standard time).
(vi) Press OK to confirm – the minute display will flash.
(vii) Use the UP and DOWN buttons to set the minutes.
(viii) Press OK to confirm.
(ix) Press MENU to finish.
Change to Program Mode – press MENU once from
Clock Mode or twice from Countdown Mode.
The number 1 and word ON will flash, meaning you
are looking at the 1st Program ON time.
If no days are shown and the time is --:--:-- this
means no time has been set.
Press RCL to delete a programmed time. To restore
a deleted time press RCL again.
MENU
MENU
RCL
RCL
(ix)
(v), (vii)
(iii)
(vi), (viii)
(ii), (iv)
(i)
UP &
UP &
OK
OK
DOWN
DOWN
Hint: If you only want to change the day or hour, you can exit setting the clock
at any time by pressing MENU.
Press the UP button to change the display – now the number 1 and word OFF
will flash, meaning you are looking at the 1st Program OFF time. Use the UP
and DOWN buttons to scroll through the timer settings.
C
Program Mode – Setting a Program
(i) In Program Mode use the UP and DOWN
buttons scroll to the program you want to set.
Example: Press the UP button once to scroll
to Program 1 ON setting. The number 1 and
word ON will flash.
(ii) Press OK to enter the Program Setting
Procedure. The day setting will flash.
(iii) Use the UP and DOWN buttons to choose
which days of the week you want the timer to
operate. Day combinations include:
- Daily (Monday – Sunday)
- Monday, Tuesday, Wednesday, Thursday,
Friday, Saturday or Sunday
- Monday – Friday only
- Monday – Saturday only
- Saturday & Sunday only
- Monday – Wednesday only
- Thursday – Saturday only
- Monday, Wednesday and Friday only
- Tuesday, Thursday and Saturday only
The day combinations allow for flexibility in
program settings. You may like to scroll through
the list a few times to get the feel for the
combinations before confirming your setting.
(iv) Press OK to confirm. The hour will flash.
(v) Use the UP and DOWN buttons to choose
what hour you want your device to switch ON.
For example if you want the timer to come
at 5:15pm press the UP button until 17:00
is displayed.
(vi) Press OK to confirm. The minute setting will
flash.
(vii) Use the UP and DOWN buttons to finish
(x), (xi),
(xii), (xiii)
(x), (xi)
UP &
OK
DOWN
(xiii)
(ix)
(ix)
UP
OK
(v), (vii)
(vi), (viii)
UP &
OK
DOWN
(i), (iii)
(ii), (iv)
UP &
OK
DOWN
D
Activate the Timer and Timer Override
To have the timer automatically operate your
device the word AUTO must be displayed when in
Clock Mode.
Press the UP button to scroll through 4 options:
- ON: power is available to your device at all times.
This is the same as leaving your device plugged
in at the wall.
setting the time you want your device to switch ON.
In this example press the UP button until 17:15 is displayed.
(viii) Press OK to confirm. The number 1 and ON will flash.
(ix) Press the UP arrow to move to the Program 1 OFF setting. Press OK to
enter the program setting procedure. The day setting will flash.
(x) Use the UP and DOWN buttons to choose which days of the week you
want the timer to switch OFF. This will probably match your settings in
Program 1 ON, but if you want your timer to remain ON overnight,
remember to choose a setting that corresponds to the following day of
the week. Press OK to confirm, the hour will flash.
(xi) Use the UP and DOWN buttons to choose the hour you want your device
to switch OFF. To set the OFF time to be 7:05pm, press the UP button
until 19:00 is displayed. Press OK to confirm and the minute setting
will flash.
(xii) Use the UP and DOWN buttons to finish setting the OFF time.
In this example press the UP button until 19:05 is displayed. Press OK
to confirm.
(xiii) Press MENU twice to return to clock mode or use the UP and DOWN
buttons to scroll to other program settings if more are required.
10:59
25
WE
ON
+1h
MENU
UP
The Random Feature will delay the preset ON and
OFF times of your set programs by between 4 and
32 minutes. This means you can set one program
to repeat every day but the switching pattern will
vary a little from day to day. This feature is ideal
to use with lamps when you go on holidays as the
switching pattern is not predictable.
To turn on the Random Feature, in Clock Mode,
10:59
25
WE
AUTO
ON
+1h
UP
10:59
25
WE
OFF
+1h
UP
10:59
25
WE
AUTO
OFF
+1h
UP
RND
DOWN
10:59
25
WE
AUTO
OFF
+1h
- AUTO ON: power is
available to your device
until the next OFF
switching time. In the
example in (xii), a lamp
plugged into the timer
will remain ON until
7:05 pm
- OFF: power will not
be available to the
device plugged into
the timer. This is the
same as turning off
the power point. NB:
This is a convenience
setting. For safety
HPM recommends
unplugging the timer
from the wall and
using the device’s OFF
switch when performing
maintenance tasks like
replacing a globe.
- AUTO OFF: power will
not be available until
the next ON switching
time. In the example in
(vii) a lamp will remain
OFF until 5:15pm
E
Random Feature
press the DOWN button once. The letters RND will show on the display.
To turn off the Random Feature, press the DOWN button again.
F
Countdown Mode
Countdown Mode lets you set up a delayed ON or
OFF switching. It’s a bit like a kitchen timer, except
instead of an alarm ringing when the clock reaches
zero, the timer switches power ON or OFF.
(i) Before setting the Countdown time choose
whether you want to turn power ON or OFF
after the time has elapsed:
• In Clock Mode: use the UP button to switch
the timer to ON or AUTO ON for a delayed
switch OFF
• In Clock Mode: use the UP button to switch
the timer to OFF or AUTO OFF for a delayed
switch ON
(ii) Press MENU twice to scroll to Countdown Mode.
The letters CTD will show on the display above the
10:59
25
WE
ON
ON
+1h
MENU
MENU
OK
UP
UP
0:00
00
OTD
+1h
DOWN
seconds.
(iii) The display shows 0:00:00 and the hour position will flash. Use the UP
and DOWN buttons to set the hour (0- 99). Press OK – the minutes
position will flash.
(iv) Use the UP and DOWN buttons to set the minute (0-59). Press OK – the
seconds position will flash.
(v) Use the UP and DOWN buttons to set the seconds (0-59). Press OK.
(vi) The timer will start to count down straight away and the letters CTD will
flash. After 2 minutes the display will return to Clock Mode. Countdown
Mode overrides the programmed settings and Random Feature.
(vii) To cancel the Countdown scroll to the Countdown Mode display and
press RCL. Hint! Pressing the RCL button in Clock Mode will adjust
between Standard and Daylight Savings Times – you must return to the
Countdown Mode display to cancel the Countdown.
Customer Service
For all customer service and
technical support enquiries please
call Monday to Friday during
business hours.
HPM Legrand Australia
1300 369 777
www.hpm.com.au
HPM Legrand - New Zealand
0800 476 009
www.hpm.co.nz
Warranty
HPM Cat D817SLIM is warranted as here and after
appears, against faulty material and/or workmanship
for a period of one year from the day of purchase. The
obligation of the manufacturer under this warranty
is limited to servicing and replacing defective parts
when the unit is returned to the authorised place of
purchase, at the purchaser’s cost. To obtain warranty
repair, the purchase receipt should be returned
with the product. This warranty becomes void on
any unit which has been tampered with or damaged
by accident, short circuited, loaded beyond rating
or damaged otherwise by improper operation. Our
goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other loss or damage. You are
also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
25521A
Loading...