QuickSpecs
HPE StoreFabric Optical Transceivers
Overview
Page 1
HPE StoreFabric Optical Transceivers
Models
HPE 10Gb SFP+ SR 100m Transceiver
Q6M30A
HPE 25Gb SFP28 SW 1-pack Pull Tab XCVR
Q2P64A
HPE 40Gb QSFP28 MPO SR4 100m Transceiver
Q7F11A
HPE 100Gb QSFP28 MPO SR4 100m Transceiver
Q2F19A
HPE 100GbE QSFP28 PSM4 2km Transceiver
Q2F20A
HPE 100GbE QSFP28 1310nm PSM4 500m Transceiver
Q8J73A
QuickSpecs
HPE StoreFabric M-
Series Optical Transceivers
Technical Specifications
2
HPE 10Gb SFP+
Ports
1 LC 10-GbE port (IEEE 802.3 Type 10Gbase-SR); Duplex: full only
Connectivity
Connectivity Connector
type
LC
Wavelength
850 nm
Physical
characteristics
Dimensions
2.19(d) x 0.54(w) x 0.47(h) in. (55.7 x 13.8 x 11.9 cm)
Environment
Weight
Transceiver form factor
SFP+
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative humidity
5% to 85%, noncondensing
Non-operating temperature
-4ºF to 185ºF (-40ºC to 85ºC)
Altitude
Up to 10,000 ft. (3 km)
Electrical
Power consumption typical
0.5w
Power consumption
Maximum
1.0w
Cabling
Cable Type
OM3, OM4.
Cable length
Fiber type
Multi-Mode
NOTE: For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish.
NOTE: Angled Physical Contact (APC) is not recommended.
Services
For details about services and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
SR 300m
Transceiver
(Q6M30A)
A 10-Gigabit
transceiver in SFP+
form-factor that
supports the SR
standard, providing
10-Gigabit
connectivity up to
300m on multimode fiber. Up to
300m (OM3); up to
375m (OM4). .
0.04 lb. (20 g)
characteristics
Up to 300m (OM3), up to 375m (OM4)
Page
QuickSpecs
HPE StoreFabric M-Series Optical Transceiver
s
Technical Specifications
Page 3
HPE 25Gb SFP28
Gigabit connectivity
up to 100m (OM4).
Ports
1 LC 25-GbE port (IEEE 802.3 Type 25Gbase-SR); Duplex: full only
Connectivity
Connectivity Connector
type
LC
Wavelength
850 nm
Physical
characteristics
Dimensions
2.19(d) x 0.54(w) x 0.47(h) in. (55.7 x 13.8 x 11.9 cm)
Environment
Weight
Transceiver form factor
SFP28
Operating temperature
Operating relative humidity
5% to 85%, noncondensing
Non-operating temperature
-4ºF to 185ºF (-40ºC to 85ºC)
Altitude
Up to 10,000 ft. (3 km)
Electrical
Power consumption typical
0.7w
Power consumption
Maximum
0.8w
Cabling
Cable Type
Cable length
Up to 70m (OM3), up to 100m (OM4)
Fiber type
Notes
For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish.
Angled Physical Contact (APC) is not recommended.
Services
For details about services and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
SR 100m
Transceiver
(Q2P64A)
A 25-Gigabit
transceiver in
SFP28 form-factor
that supports the
SR standard,
providing 25-
up to 100m on
multi-mode fiber.
Up to 70m (OM3);
0.04 lb. (20 g)
32ºF to 158ºF (0ºC to 70ºC)
.
characteristics
OM3, OM4
Multi-Mode
QuickSpecs
HPE StoreFabric M-Series Optical Transceiver
s
Technical Specifications
Page 4
HPE 40Gb QSFP28
Ports
1 MPO 40-GbE port (IEEE
802.3 Type 40Gbase-SR4);
Connectivity
Connector type
MPO
Wavelength
850 nm
Physical
characteristics
Dimensions
0.72 x 2.86 x 0.33 in. (18.35 x 72.7 x 8.5 mm)
Environment
Weight
0.08 lb. (36 g)
Transceiver form factor
QSFP+
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative humidity
5% to 85%, noncondensing
Non-operating/Storage
temperature
-4ºF to 185ºF (-40ºC to 85ºC)
Altitude
Up to 10,000 ft. (3 km)
Electrical
Power consumption typical
2.3 w
Power consumption
Maximum
2.5 w
Cabling
Cable type
OM3, OM4
Cable length
Up to 70m (OM3), up to 100m OM4
Fiber type
Multi-Mode
NOTE: Conditioning patch cord cables are not supported.
NOTE: Angled Physical Contact (APC) is not recommended.
Services
For details about services and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
MPO SR4 100m
Transceiver
Transceiver
(Q7F11A)
A 40-Gigabit
transceiver in
QSFP+ form-factor
that supports the
4x10-Gigabit SR
standard, providing
40-Gigabit
connectivity up to
100m with multimode fiber .
characteristics
NOTE: For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish.
QuickSpecs
HPE StoreFabric M-Series Optical Transceiver
s
Technical Specifications
Page 5
HPE 100Gb
operates at signaling
Ports
1 MPO 100-GbE port (IEEE
802.3 Type 100Gbase-SR4);
Connectivity
Connector type
MPO
Wavelength
850 nm
Physical
characteristics
Dimensions
0.72 x 2.86 x 0.33 in. (18.35 x 72.7 x 8.5 mm)
Environment
Weight
0.0
Transceiver form factor
QSFP28
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative humidity
5% to 85%, noncondensing
Non-operating/Storage
temperature
-4ºF to 185ºF (-40ºC to 85ºC)
Altitude
Up to 10,000 ft. (3 km)
Electrical
characteristics
Power consumption typical
2.3 w
Power consumption
maximum
2.5 w
Cabling
Cable type
OM3, OM4
Cable length
Up to 70m (OM3), up to 100m (OM4)
Fiber type
Multi-Mode
NOTE: Conditioning patch cord cables are not supported.
NOTE:
NOTE: Angled Physical Contact (APC) is not recommended.
Services
For details about services and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
QSFP28 MPO SR4
100m Transceiver
(Q2F19A)
A 100-Gigabit
transceiver in
QSFP28 form-factor
that supports the
4x25-Gigabit SR4
standard, providing
100-Gigabit
connectivity up to
100m on using
standard MPO
connector with
multi-mode fiber.
Each channel/fiber
8 lb. (36 g)
rates up to
25.78125 GBd
For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish.
QuickSpecs
HPE StoreFabric M-Series Optical Transceiver
s
Technical Specifications
Page 6
HPE 100Gb
(
factor that supports
PSM4 parallel single
Ports
1 MPO 100-GbE port (IEEE
802.3bm Type 100G PSM4);
Connectivity
Connector type
MPO
Wavelength
1550 nm
Physical
characteristics
Dimensions
0.72 x 2.86 x 0.33 in. (18.35 x 72.7 x 8.5 mm)
Environment
Weight
Transceiver form factor
Operating temperature
Operating relative humidity
Non-operating/Storage
temperature
-4ºF to 185ºF (-40ºC to 85ºC)
Altitude
Electrical
Power consumption typical
2.5 w
Power consumption
maximum
2.7 w
Cabling
Cable type
Low metal content, single-mode fiber-optic, complying
with ITU-T G.652 and ISO/IEC 793-2 Type B1
Cable length
Up to 2km
Fiber type
Single Mode
NOTE: Conditioning patch cord cables are not supported.
NOTE: Angled Physical Contact (APC) is required to reduce reflection.
Services
For details about services and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
QSFP28 MPO
PSM4 2km
Transceiver
Q2F20A)
A 100-Gigabit
transceiver in
QSFP28 form-
the 100-Gigabit
PSM4 standard,
The transceiver
operates over
0.08 lb. (36 g)
QSFP28
32ºF to 158ºF (0ºC to 70ºC)
5% to 85%, noncondensing
mode ribbon fiber,
up to 2km link
Up to 10,000 ft. (3 km)
characteristics
NOTE: For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish.
QuickSpecs
HPE StoreFabric M-Series Optical Transceiver
s
Technical Specifications
Page 7
HPE 100GbE
factor that supports
Ports
1 MPO 100-GbE port (IEEE
802.3bm Type 100G PSM4);
Connectivity
Connector type
MPO
Wavelength
1310 nm
Physical
characteristics
Dimensions
0.72 x 2.86 x 0.33 in. (18.35 x 72.7 x 8.5 mm)
Environment
Weight
0.0
Transceiver form factor
QSFP28
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative humidity
5% to 85%, noncondensing
Non-operating/Storage
temperature
-4ºF to 185ºF (-40ºC to 85ºC)
Altitude
Up to 10,000 ft. (3 k
Electrical
Power consumption typical
2.5 w
Power consumption
maximum
2.7 w
Cabling
Cable type
Low metal content, single-mode fiber-optic, complying
with ITU-T G.652 and ISO/IEC 793-2 Type B1
Cable length
Up to 500m
Fiber type
Single Mode
NOTE: Conditioning patch cord cables are not supported.
NOTE: Angled Physical Contact (APC) is required to reduce reflection.
Services
For details about services and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
QSFP28 1310nm
PSM4 500m
Transceiver
(Q8J73A)
A 100-Gigabit
transceiver in
QSFP28 form-
the 100-Gigabit
PSM4 standard,
The transceiver
operates over
PSM4 parallel
single mode ribbon
fiber, up to 500m
link
8 lb. (36 g)
m)
characteristics
NOTE: For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish.
QuickSpecs
HPE StoreFabric M-
Series Optical Transceivers
Summary of Changes
8
Date
Version History
Action
Description of Change
04-Dec-2017
From Version 1 to 2
Added
Added new 25GbE and 100GbE transceivers.
25-Sept-2017
Version 1
Created
New QuickSpecs
Sign up for updates
© Copyright 2017 Hewlett Packard Enterprise Development LP. The information contained herein is subject to
change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the
express warranty statements accompanying such products and services. Nothing herein should be construed as
constituting an addi
omissions contained herein.
a000
21855enw - 16025 - Worldwide – V2 - 4-December-2017
tional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or
Page
Loading...