HPE P02463-B21, PERFDL380-006 Getting Started Guide
QuickSpecs
HPE ProLiant DL380 Gen10 Carrier Grade Supplement
Overview
Page 1
HPE ProLiant DL380 Gen10 Carrier Grade Server NEBS Level 3 and ETSI Certified
This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are
ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales
representative for information on configurable product offerings and requirements.
1. Factory Integrated Models must start with a CTO Server.
2. FIO indicates that this option is only available as a factory installable option.
3. All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives
ordered with the server.
4. Some options may not be integrated at the factory. Contact your local sales representative for additional information.
IMPORTANT: To yield a carrier grade server that is compliant with all the required technical criteria, the product content is
limited to what is listed in this document. In addition, the following kits must be installed:
1. HP DL380 Gen10 High Performance Fan Kit - 867810-B21
2. All installed PCI risers must be NEBS certified versions:
HPE DL380 Gen10 x8/16/8 NEBS Riser Kit - 873209-B21
HPE DL380 Gen10 x8/16/8 M.2 NEBS Riser Kit - 826701-B21
HPE DL380 Gen10 x16 Tertiary NEBS Riser Kit - 826702-B21
NOTE: M.2 Riser is only supported in the primary PCI riser location.
Please refer to the HPE DL380 Gen10 Carrier Grade Conversion documentation on the HPE web
site: http://www.hpe.com/services/hpsc
QuickSpecs
HPE ProLiant DL380 Gen10 Carrier Grade Supplement
Configuration Information
- Factory Integrated Models
Page 2
Step 1: Base Configuration (choose one of the following configurable models)
CTO Server
HPE ProLiant DL380 Gen10 8 SFF CTO Server
SKU Number
868703-B21
TAA SKU
875782-B21
Processor
Not included as standard
DIMM Slots
24-DIMM slots
Storage Controller
Embedded SW RAID with 14 SATA ports (12-ports accessible), choice of HPE modular Smart Array
and PCIe plug-in controller
PCIe
Three standard in primary riser (with dual M.2 support)
Drive Cage - included
8 SFF
Network Controller
HPE 1Gb Ethernet 4-Port 331i Adapter plus optional HPE FlexibleLOM or stand up card
Fans
4-Standard
Management
HPE iLO with Intelligent Provisioning (standard), iLO Advances and OneView (optional)
USB
1x 3.0 standard plus iLo front service port
NOTE: HPE offers multiple Trade Agreement Act (TAA) compliant configurations to meet the needs of US Federal
TAA
NOTE: All CTO servers are Energy Star 2.1 compliant.
Step 2a: Choose Required Options - Processors
(only one of the following unless otherwise noted)
Please select one –L21 processor required below.
and type of DIMMs installed.
Processor Option Kits
Required
Processor
HPE DL380 Gen10 Intel Xeon-Gold 6152 (2.1GHz/22-core/140W) FIO Processor Kit
826886-L21
NOTE: Ships with Performance Heatsink.
NOTE: Supports “Core boosting” Learn more http://www.hpe.com/info/ist.
NOTE: To enable this feature an iLO Advanced, or iLO Advanced Premium Security edition License are
required.
HPE DL380 Gen10 Intel Xeon-Gold 6140 (2.3GHz/18-core/150W) FIO Processor Kit
826878-L21
NOTE: Ships with Performance Heatsink.
HPE DL380 Gen10 Intel Xeon-Gold 6138 (2.0GHz/20-core/125W)FIO Processor Kit
826876-L21
NOTE: High frequency bin targeting FSI workloads. Configuration restrictions will apply, support on 8SFF
only.
HPE DL38X Gen10 High Performance Temperature Fan Kit (867810-B21) to be selected.
Government customers. These products are either manufactured or substantially transformed in a designated country.
compliance is only provided when HPE options are included as part of factory integrated orders (CTO).
NOTE: TAA chassis are only orderable in North America and Canada.
For second processor, please select the same processor model with –B21 from Core Options – HPE Processors section.
For example: first processor, select 874752-L21 then for second processor, select 874752-B21.
NOTE: 8SFF CTO 1P models ship with 4 standard fans. The second processor option kit contains 2 additional fans.
NOTE: Maximum memory capacity per processor is dependent on processor models. All processors support up to 768 GB
max memory per processor except “M” model processors will support up to 1.5 TB max memory per processor.
NOTE: Mixing of 2 different processor models are NOT allowed.
NOTE: DDR4 speed is the maximum memory speed of the processor. Actual memory speed may depend on the quantity
QuickSpecs
HPE ProLiant DL380 Gen10 Carrier Grade Supplement
Configuration Information
- Factory Integrated Models
Page 3
NOTE: For additional details on this processor please visit:
https://h20195.www2.hpe.com/v2/Getdocument.aspx?docname=a00039606enw
HPE DL380 Gen10 Intel Xeon-Gold 6130 (2.1GHz/16-core/120W) FIO Processor Kit
826866-L21
HPE DL380 Gen10 Intel Xeon-Gold 5120 (2.2GHz/14-core/105W) FIO Processor Kit
826856-L21
HPE DL380 Gen10 Intel Xeon-Gold 5118 (2.3GHz/12-core/105W) FIO Processor Kit
826854-L21
HPE DL380 Gen10 Intel Xeon-Silver 4116 (2.1GHz/12-core/85W) FIO Processor Kit
826852-L21
HPE DL380 Gen10 Intel Xeon-Silver 4114 (2.2GHz/10-core/85W) FIO Processor Kit
826850-L21
HPE DL380 Gen10 Intel Xeon-Silver 4110 (2.1GHz/8-core/85W) FIO Processor Kit
826846-L21
HPE DL380 Gen10 Intel Xeon-Silver 4108 (1.8GHz/8-core/85W) FIO Processor Kit
826848-L21
HPE DL380 Gen10 Intel Xeon-Bronze 3104 (1.7GHz/6-core/85W) FIO Processor Kit
873641-L21
NOTE: Processors above 130W use a High Performance Heatsink
Step 2b: Choose Memory Options
Please select one or more memory from below.
NOTE: The maximum memory speed is a function of the memory type, memory configuration, and processor model.
HPE 8GB (1x8GB) Single Rank x8 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit
815097-B21
HPE 8GB (1x8GB) Dual Rank x8 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit
876181-B21
HPE 16GB (1x16GB) Single Rank x4 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit
815098-B21
HPE 16GB (1x16GB) Dual Rank x8 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit
835955-B21
HPE 32GB (1x32GB) Dual Rank x4 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit
815100-B21
NOTE: Scalable Persistent Memory requires dedicated flash backup. The 1.6TB NVME MU SFF (877994-
installation.
NOTE: Scalable Persistent Memory requires Back up power and the 800W PSU/400w BBU (827608-B21)
needs to be selected.
Step 2c: Choose Power Supplies
Select one or two power supplies from below.
NOTE: Mixing of 2 different power supplies is NOT allowed.
HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit
865414-B21
HPE 800W Flex Slot -48VDC Hot Plug Low Halogen Power Supply Kit
865434-B21
Step 3: Choose Additional Factory Integratable Options
One of the following from each list may be selected if desired at time of factory integration
For new Gen10 memory population rule whitepaper and optimal memory performance guidelines, please go
to: https://www.hpe.com/docs/memory-population-rules
For Gen10 memory speed table, please go to: https://www.hpe.com/docs/memory-speed-table
For memory Reliability, Accessibility, Serviceability (RAS) features whitepaper like Gen10 Fast Fault Tolerance and legacy
mirrored memory feature etc. please go to: http://www.hpe.com/docs/memory-ras-feature
NOTE: Memory DIMM availability with a server platform is dependent upon completion of certification testing.
B21) drive is required, with respective drive cages and associated options (Enablement kit, riser and Fan
kit) and must be installed in Box 3. A Qty of 2 are required for the 256GB and 4 required for the 512GB
QuickSpecs
HPE ProLiant DL380 Gen10 Carrier Grade Supplement
Configuration Information
- Factory Integrated Models
Page 4
HPE Security Options
HPE Trusted Platform Module 2.0 Gen10 Option
864279-B21
NOTE: HPE Trusted Platform Module 2.0 option works with Gen10 servers with UEFI Mode not Legacy
module (of any type) installed only once. It cannot be replaced
with any other TPM module.
HPE Gen10 TPM 1.2 FIO Setting
872108-B21
NOTE: TPM 2.0 is set as default, for 1.2 TPM setting instead, please select this option.
HPE Unique Options
HPE DL380 Gen10 x8/x16/x8 M.2 NEBS Riser Kit
826701-B21
NOTE: Primary Riser Slot 1.
NOTE: Bus width x16, x16, Connector Width x16, x16.
HPE DL38X Gen10 x8/x16/x8 PCIe NEBS Riser Kit
873209-B21
NOTE: Secondary Riser, Connector in slot 2 & 3 for GPU support.
NOTE: Bus width x16, x16, Connector Width x16, x16.
HPE DL380 Gen10 x16 Tertiary NEBS Riser
826702-B21
NOTE: Supports 1x 16 slot in the Tertiary location.
NOTE: Bus width x16 Connector Width x16.
HPE 2U Bezel Air Filter NEBS-compliant Kit
P05420-B21
HPE 48VDC 2.85m Power Cable
Q0H80A
Step 4: Choose additional options for Factory Integration from Core and Additional
Options sections below
Mode. It is not compatible with HPE ProLiant Gen8 servers or earlier generation variants.
NOTE: HPE server systems can have a TPM
NOTE: Supports Full Height and Full length cards.
NOTE: Supports Full Height and Full length cards.
NOTE: Supports Full Height and full-length card.
Loading...