HPE P01880-B21 User Manual

HPE ProLiant DL360 Gen10 Server User Guide

Abstract
This document is for the person who installs, administers, and troubleshoots servers and storage systems. Hewlett Packard Enterprise assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
Part Number: 869840-008 Published: July 2019 Edition: 8
©
Copyright 2018-2019 Hewlett Packard Enterprise Development LP
Notices
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise website.
Acknowledgments
Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Contents

Component identification.......................................................................7
Front panel components............................................................................................................... 7
Front panel LEDs and buttons...................................................................................................... 9
UID button functionality.................................................................................................... 11
Front panel LED power fault codes.................................................................................. 11
Systems Insight Display LEDs.................................................................................................... 11
Systems Insight Display combined LED descriptions................................................................. 13
Rear panel components..............................................................................................................15
Rear panel LEDs.........................................................................................................................15
System board components......................................................................................................... 17
System maintenance switch descriptions........................................................................ 18
NMI functionality...............................................................................................................18
DIMM slot locations..........................................................................................................18
DIMM label identification.................................................................................................. 19
NVDIMM identification......................................................................................................20
NVDIMM LED identification..............................................................................................22
HPE Persistent Memory module label identification........................................................ 23
Device numbers.......................................................................................................................... 23
Hot-plug drive LED definitions.................................................................................................... 25
NVMe SSD LED definitions........................................................................................................ 26
uFF drive components and LEDs............................................................................................... 27
Hot-plug fans...............................................................................................................................28
HPE Smart Array P824i-p MR Gen10 Controller........................................................................ 30
HPE InfiniBand HDR/Ethernet 940QSFP 56x16 adapter LEDs..................................................31
Operations............................................................................................. 32
Power up the server....................................................................................................................32
Power down the server............................................................................................................... 32
Extend the server from the rack..................................................................................................32
Remove the server from the rack................................................................................................33
Remove the access panel...........................................................................................................33
Install the access panel...............................................................................................................33
Remove the hot-plug fan.............................................................................................................34
Remove the primary PCI riser cage............................................................................................35
Install the primary PCI riser cage................................................................................................36
Remove the secondary PCI riser cage....................................................................................... 37
Install the secondary PCI riser cage........................................................................................... 38
Remove the 8 SFF drive backplane............................................................................................39
Release the cable management arm ......................................................................................... 39
Setup...................................................................................................... 41
Optional service.......................................................................................................................... 41
Optimum environment.................................................................................................................41
Space and airflow requirements.......................................................................................41
Temperature requirements...............................................................................................42
Power requirements......................................................................................................... 42
Electrical grounding requirements....................................................................................43
Connecting a DC power cable to a DC power source......................................................43
3
Server warnings and cautions.....................................................................................................44
Rack warnings.............................................................................................................................45
Identifying the contents of the server shipping carton.................................................................46
Installing hardware options ........................................................................................................ 46
Installing the server into the rack................................................................................................ 46
Operating system........................................................................................................................47
Installing the operating system with Intelligent Provisioning............................................ 47
Selecting boot options in UEFI Boot Mode................................................................................. 47
Selecting boot options.................................................................................................................48
Registering the server.................................................................................................................48
Hardware options installation..............................................................49
Hewlett Packard Enterprise product QuickSpecs....................................................................... 49
Introduction................................................................................................................................. 49
Installing a redundant hot-plug power supply............................................................................. 49
Memory options...........................................................................................................................50
DIMM and NVDIMM population information.....................................................................50
DIMM-processor compatibility..........................................................................................50
HPE SmartMemory speed information.............................................................................51
Installing a DIMM..............................................................................................................51
HPE 16GB NVDIMM option............................................................................................. 52
HPE Persistent Memory option........................................................................................ 56
Installing a high-performance fan................................................................................................59
Drive options............................................................................................................................... 61
Hot-plug drive guidelines..................................................................................................61
Removing the hard drive blank........................................................................................ 61
Installing a hot-plug SAS or SATA drive........................................................................... 62
Removing a hot-plug SAS or SATA hard drive.................................................................63
Installing the NVMe drives............................................................................................... 63
Removing and replacing an NVMe drive..........................................................................65
Installing a uFF drive and SCM drive carrier....................................................................65
Removing and replacing a uFF drive............................................................................... 66
Installing an 8 SFF optical drive....................................................................................... 67
Universal media bay options.......................................................................................................68
Installing a 2 SFF SAS/SATA drive cage..........................................................................68
Installing a 2 SFF NVMe drive cage option......................................................................71
Installing a 2 SFF HPE Smart Carrier M.2 (SCM) drive cage.......................................... 74
Installing an 8 SFF display port/USB/optical blank option................................................76
Installing the 4 LFF optical drive option...................................................................................... 78
Installing the rear drive riser cage option.................................................................................... 81
Primary PCI riser cage options................................................................................................... 84
Installing an optional primary PCI riser board ................................................................. 84
Installing the SATA M.2 2280 riser option........................................................................ 86
Installing an expansion board in the primary riser cage...................................................88
Installing an accelerator or GPU in the primary riser cage...............................................90
Secondary PCI riser options....................................................................................................... 91
Installing a secondary full-height PCI riser cage option................................................... 91
Installing a secondary low-profile PCIe slot riser cage option..........................................95
Installing an expansion board in the secondary riser cage.............................................. 96
Installing an accelerator or GPU in the secondary riser cage.......................................... 99
Controller options......................................................................................................................101
Installing an HPE Smart Array P408i-a SR Gen10 Controller option.............................102
Installing an HPE Smart Array P408i-p SR Gen10 Controller option.............................105
Installing an HPE Smart Array P816i-a SR Gen10 Controller option.............................108
Installing an HPE Smart Array P824i-p MR Gen10 controller in a configured server.....111
4
Installing the operating system with the HPE Smart Array MR Gen10 P824i-p
controller driver...............................................................................................................112
Processor and heatsink options................................................................................................ 113
Installing a processor heatsink assembly.......................................................................113
Installing a high-performance heatsink...........................................................................115
Processor, heatsink, and socket components................................................................119
Installing the Systems Insight Display power module............................................................... 120
Installing the 4 LFF display port/USB module...........................................................................124
Installing the serial cable option................................................................................................126
Installing the Chassis Intrusion Detection switch option........................................................... 128
Installing a FlexibleLOM option.................................................................................................129
Energy pack options................................................................................................................. 131
HPE Smart Storage Battery........................................................................................... 131
HPE Smart Storage Hybrid Capacitor............................................................................132
Minimum firmware versions............................................................................................132
Energy pack option configurations................................................................................. 132
HPE Trusted Platform Module 2.0 Gen10 option......................................................................137
Overview........................................................................................................................ 137
HPE Trusted Platform Module 2.0 Guidelines................................................................138
Installing and enabling the HPE TPM 2.0 Gen10 Kit..................................................... 138
Cabling................................................................................................. 144
Cabling overview ......................................................................................................................144
SFF cables................................................................................................................................144
SFF configuration cable routing..................................................................................... 145
Additional SFF cabling................................................................................................... 149
LFF cables................................................................................................................................ 150
LFF configuration cable routing......................................................................................150
Additional LFF cabling....................................................................................................150
Software and configuration utilities.................................................. 152
Server mode..............................................................................................................................152
Product QuickSpecs................................................................................................................. 152
Active Health System Viewer....................................................................................................152
Active Health System..................................................................................................... 153
HPE iLO 5................................................................................................................................. 154
iLO Federation............................................................................................................... 154
iLO Service Port............................................................................................................. 154
iLO RESTful API.............................................................................................................155
RESTful Interface Tool................................................................................................... 155
iLO Amplifier Pack..........................................................................................................155
Integrated Management Log.....................................................................................................156
Intelligent Provisioning.............................................................................................................. 156
Intelligent Provisioning operation................................................................................... 156
Management Security............................................................................................................... 157
Scripting Toolkit for Windows and Linux................................................................................... 157
UEFI System Utilities................................................................................................................ 158
Selecting the boot mode ............................................................................................... 158
Secure Boot................................................................................................................... 159
Launching the Embedded UEFI Shell ........................................................................... 159
HPE Smart Storage Administrator............................................................................................ 160
HPE MR Storage Administrator................................................................................................ 161
HPE InfoSight for servers ........................................................................................................ 161
StorCLI......................................................................................................................................161
5
USB support..............................................................................................................................162
External USB functionality..............................................................................................162
Redundant ROM support.......................................................................................................... 162
Safety and security benefits........................................................................................... 162
Keeping the system current...................................................................................................... 162
Updating firmware or system ROM................................................................................ 162
Drivers............................................................................................................................165
Software and firmware................................................................................................... 165
Operating system version support................................................................................. 165
HPE Pointnext Portfolio..................................................................................................165
Proactive notifications.................................................................................................... 166
Troubleshooting.................................................................................. 167
Troubleshooting resources........................................................................................................167
Removing and replacing the system battery....................................168
Specifications......................................................................................170
Environmental specifications.................................................................................................... 170
Server specifications.................................................................................................................170
Power supply specifications......................................................................................................171
HPE 500W Flex Slot Platinum Hot-plug Low Halogen Power Supply............................171
HPE 800W Flex Slot Platinum Hot-plug Low Halogen Power Supply............................172
HPE 800W Flex Slot Titanium Hot-plug Low Halogen Power Supply............................173
HPE 800W Flex Slot Universal Hot-plug Low Halogen Power Supply...........................174
HPE 800W Flex Slot -48VDC Hot-plug Low Halogen Power Supply.............................175
HPE 1600W Flex Slot Platinum Hot-plug Low Halogen Power Supply..........................176
Hot-plug power supply calculations.......................................................................................... 177
Websites.............................................................................................. 178
Support and other resources.............................................................179
Accessing Hewlett Packard Enterprise Support....................................................................... 179
Accessing updates....................................................................................................................179
Customer self repair..................................................................................................................180
Remote support........................................................................................................................ 180
Warranty information.................................................................................................................180
Regulatory information..............................................................................................................181
Documentation feedback.......................................................................................................... 181
Acronyms and abbreviations.............................................................182
6

Component identification

Front panel components

8 SFF
Item Description
1 Serial label pull tab
2 Display port (optional)
3 Optical drive (optional)
4 USB 2.0 port (optional)
5 USB 3.0 port
6 iLO Service Port
The operating system does not recognize this port as a USB port.
7 SAS/SATA drive bays
4 LFF
Item Description
1 Optical drive blank (optional)
2 Serial label pull tab
3 Display port (optional)
4 USB 2.0 port (optional)
Table Continued
Component identification 7
Item Description
5 iLO Service Port
The operating system does not recognize this port as a USB port.
6 USB 3.0 port
7 SAS/SATA drive bays
10 SFF NVMe/SAS Combo
Item Description
1 Serial label pull tab
2 Systems Insight Display (optional)
3 USB 3.0 port
4 SAS/SATA/NVMe drive bays
When the 10 SFF NVMe/SAS backplane option is installed, NVMe drives must be installed in bays 9 and 10. The other bays support a mix of NVMe and SAS drives.
8 Component identification

Front panel LEDs and buttons

8 SFF/10 SFF
Item Description Status
1 UID button/LED
1
Solid blue = Activated
2 Power On/Standby button and
system power LED
3 Health LED
1
4 NIC status LED
1
1
Flashing blue:
1 Hz = Remote management or firmware upgrade in progress
4 Hz = iLO manual reboot sequence initiated
8 Hz = iLO manual reboot sequence in progress
Off = Deactivated
Solid green = System on
Flashing green = Performing power on sequence
Solid amber = System in standby
Off = No power present
2
Solid green = Normal
Flashing green = iLO is rebooting.
Flashing amber = System degraded
Flashing red = System critical
3
Solid green = Link to network
Flashing green = Network active
Off = No network activity
Component identification 9
1
When all four LEDs described in this table flash simultaneously, a power fault has occurred.
2
Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has occurred, or the power button cable is disconnected.
3
If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the system health status.
4 LFF
Item Description Status
1 UID button/LED
1
Solid blue = Activated.
Flashing blue:
1 Hz = Remote management or firmware upgrade in progress.
4 Hz = iLO manual reboot sequence initiated.
8 Hz = iLO manual reboot sequence in progress.
Off = Deactivated.
2 NIC status LED
1
Solid green = Link to network.
Flashing green = Network active.
Off = No network activity.
Table Continued
10 Component identification
Item Description Status
3 Health LED
1
Solid green = Normal.
Flashing green = iLO is rebooting.
Flashing amber = System degraded.
Flashing red = System critical.
4 Power On/Standby button and
system power LED
1
Solid green = System on.
Flashing green = Performing power on sequence.
Solid amber = System in standby.
Off = No power present.
1
When all four LEDs described in this table flash simultaneously, a power fault has occurred.
2
To identify components in a degraded or critical state, see the Systems Insight Display LEDs, check iLO/BIOS logs, and reference the server troubleshooting guide.
3
Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has occurred, or the power button cable is disconnected.

UID button functionality

The UID button can be used to display the Server Health Summary when the server will not power on. For more information, see the latest HPE iLO 5 User Guide on the Hewlett Packard Enterprise website.

Front panel LED power fault codes

The following table provides a list of power fault codes, and the subsystems that are affected. Not all power faults are used by all servers.
2
3
Subsystem LED behavior
System board 1 flash
Processor 2 flashes
Memory 3 flashes
Riser board PCIe slots 4 flashes
FlexibleLOM 5 flashes
Removable HPE Smart Array SR Gen10 controller 6 flashes
System board PCIe slots 7 flashes
Power backplane or storage backplane 8 flashes
Power supply 9 flashes

Systems Insight Display LEDs

The Systems Insight Display LEDs represent the system board layout. The display enables diagnosis with the access panel installed.
Component identification 11
Description Status
Processor LEDs
DIMM LEDs
Fan LEDs
NIC LEDs
1
Power supply LEDs
Off = Normal
Amber = Failed processor
Off = Normal
Amber = Failed DIMM or configuration issue
Off = Normal
Amber = Failed fan or missing fan
Off = No link to network
Solid green = Network link
Flashing green = Network link with activity
If power is off, the front panel LED is not active. For status, see Rear panel LEDs on page 15.
Off = Normal
Solid amber = Power subsystem degraded, power supply failure, or input power lost.
PCI riser LED
Over temp LED
12 Component identification
Off = Normal
Amber = Incorrectly installed PCI riser cage
Off = Normal
Amber = High system temperature detected
Table Continued
Description Status
Amp Status LED
Power cap LED
1
For Networking Choice (NC) server models, the embedded NIC ports are not equipped on the server. Therefore, the NIC LEDs on the Systems Insight Display will flash based on the FlexibleLOM network port activity. In the case of a dual-port FlexibleLOM, only NIC LED 1 and 2 will illuminate to correspond with the activity of the respective network ports.
When the health LED on the front panel illuminates either amber or red, the server is experiencing a health event. For more information on the combination of these LEDs, see Systems Insight Display combined LED descriptions on page 13).
Off = AMP modes disabled
Solid green = AMP mode enabled
Solid amber = Failover
Flashing amber = Invalid configuration
Off = System is in standby, or no cap is set.
Solid green = Power cap applied

Systems Insight Display combined LED descriptions

The combined illumination of the following LEDs indicates a system condition:
Systems Insight Display LEDs
System power LED
Health LED
Systems Insight Display LED and color
Processor (amber) Red Amber One or more of the following
Processor (amber) Amber Green Processor in socket X is in a pre-
DIMM (amber) Red Green One or more DIMMs have failed.
Health LED
System power LED
Status
conditions may exist:
Processor in socket X has failed.
Processor X is not installed in the socket.
Processor X is unsupported.
ROM detects a failed processor during POST.
failure condition.
DIMM (amber) Amber Green DIMM in slot X is in a pre-failure
condition.
Table Continued
Component identification 13
Systems Insight Display LED and color
Over temp (amber) Amber Green The Health Driver has detected a
Over temp (amber) Red Amber The server has detected a hardware
PCI riser (amber) Red Green The PCI riser cage is not seated
Fan (amber) Amber Green One fan has failed or has been
Fan (amber) Red Green Two or more fans have failed or been
Power supply (amber) Red Amber One or more of the following
Health LED
System power LED
Status
cautionary temperature level.
critical temperature level.
properly.
removed.
removed.
conditions may exist:
Only one power supply is installed and that power supply is in standby.
Power supply fault
System board fault
Power supply (amber) Amber Green One or more of the following
conditions may exist:
Redundant power supply is installed and only one power supply is functional.
AC power cord is not plugged into redundant power supply.
Redundant power supply fault
Power supply mismatch at POST or power supply mismatch through hot-plug addition
Power cap (off) Amber Standby
Power cap (green) Flashing
green
Power cap (green) Green Power is available.
Power cap (flashing amber) Amber Power is not available.
IMPORTANT: If more than one DIMM slot LED is illuminated, further troubleshooting is required. Test each bank of DIMMs by removing all other DIMMs. Isolate the failed DIMM by replacing each DIMM in a bank with a known working DIMM.
Waiting for power
14 Component identification

Rear panel components

Item Description
1 Slot 1 PCIe3
2 Slot 2 PCIe3
3 Slot 3 PCIe3 (optional - requires second processor)
4 Power supply 2 (PS2)
5 Power supply 1 (PS1)
6 Video port
7 NIC ports (if equipped)
8 iLO Management Port
9 Serial port (optional)
10 USB 3.0 ports
11 FlexibleLOM (optional)

Rear panel LEDs

Component identification 15
Item Description Status
1 UID LED Solid blue = Identification is activated.
Flashing blue = System is being managed remotely.
Off = Identification is deactivated.
2R iLO 5/standard
NIC activity LED
2L iLO 5/standard
NIC link LED
3 Power supply 2
LED
4 Power supply 1
LED
Solid green = Activity exists.
Flashing green = Activity exists.
Off = No activity exists.
Solid green = Link exists.
Off = No link exists.
Solid green = Normal
Off = One or more of the following conditions exists:
AC power unavailable
Power supply failed
Power supply in standby mode
Power supply exceeded current limit.
Solid green = Normal
Off = One or more of the following conditions exists:
AC power unavailable
Power supply failed
Power supply in standby mode
Power supply exceeded current limit.
16 Component identification

System board components

Item Description
1 FlexibleLOM connector
2 Primary (processor 1) PCIe riser connector
3 System maintenance switch
4 Front display port/USB 2.0 connector
5 x4 SATA port 1
6 x4 SATA port 2
7 x2 SATA port 3
8 x1 SATA port 4
9 Front power/USB 3.0 connector
10 Optical/SATA port 5
11 Energy pack connector
12 Micro SD card slot
13 Chassis Intrusion Detection connector
14 Drive backplane power connector
15 Dual internal USB 3.0 connector
16 Type-a SmartArray connector
17 Secondary (processor 2) PCIe riser connector
18 System battery
19 TPM connector (optional)
20 Serial port connector (optional)
Component identification 17

System maintenance switch descriptions

Position Default Function
1
S1
S2 Off Reserved
S3 Off Reserved
S4 Off Reserved
1
S5
Off
Off
Off = iLO security is enabled.
On = iLO security is disabled.
Off = Power-on password is enabled.
On = Power-on password is disabled.
S61, 2,
3
Off
S7 Off Reserved
S8 Reserved
S9 Reserved
S10 Reserved
S11 Reserved
S12 Reserved
1
To access the redundant ROM, set S1, S5, and S6 to On.
2
When the system maintenance switch position 6 is set to the On position, the system is prepared to restore all configuration settings to their manufacturing defaults.
3
When the system maintenance switch position 6 is set to the On position and Secure Boot is enabled, some configurations cannot be restored. For more information, see Secure Boot on page 159.

NMI functionality

An NMI crash dump enables administrators to create crash dump files when a system is hung and not responding to traditional debugging methods.
Off = No function
On = Restore default manufacturing settings
An analysis of the crash dump log is an essential part of diagnosing reliability problems, such as hanging operating systems, device drivers, and applications. Many crashes freeze a system, and the only available action for administrators is to cycle the system power. Resetting the system erases any information that could support problem analysis, but the NMI feature preserves that information by performing a memory dump before a hard reset.
To force the OS to invoke the NMI handler and generate a crash dump log, the administrator can use the iLO Virtual NMI feature.

DIMM slot locations

DIMM slots are numbered sequentially (1 through 12) for each processor. The supported AMP modes use the letter assignments for population guidelines.
18 Component identification

DIMM label identification

To determine DIMM characteristics, see the label attached to the DIMM. The information in this section helps you to use the label to locate specific information about the DIMM.
Item Description Example
1 Capacity
2 Rank
8 GB
16 GB
32 GB
64 GB
128 GB
1R = Single rank
2R = Dual rank
4R = Quad rank
8R = Octal rank
Table Continued
Component identification 19
Item Description Example
3 Data width on DRAM
4 Memory generation
5 Maximum memory speed
6 CAS latency
x4 = 4-bit
x8 = 8-bit
x16 = 16-bit
PC4 = DDR4
2133 MT/s
2400 MT/s
2666 MT/s
2933 MT/s
P = CAS 15-15-15
T = CAS 17-17-17
U = CAS 20-18-18
V = CAS 19-19-19 (for RDIMM, LRDIMM)
V = CAS 22-19-19 (for 3DS TSV LRDIMM)
7 DIMM type
For more information about product features, specifications, options, configurations, and compatibility, see the HPE DDR4 SmartMemory QuickSpecs on the Hewlett Packard Enterprise website (http://
www.hpe.com/support/DDR4SmartMemoryQS).

NVDIMM identification

NVDIMM boards are blue instead of green. This change to the color makes it easier to distinguish NVDIMMs from DIMMs.
To determine NVDIMM characteristics, see the full product description as shown in the following example:
Y = CAS 21-21-21 (for RDIMM, LRDIMM)
Y = CAS 24-21-21 (for 3DS TSV LRDIMM)
R = RDIMM (registered)
L = LRDIMM (load reduced)
E = Unbuffered ECC (UDIMM)
20 Component identification
Item Description Definition
1 Capacity 16 GiB
2 Rank 1R (Single rank)
3 Data width per DRAM chip x4 (4 bit)
4 Memory type NN4=DDR4 NVDIMM-N
5 Maximum memory speed 2667 MT/s
6 Speed grade V (latency 19-19-19)
7 DIMM type RDIMM (registered)
8 Other
For more information about NVDIMMs, see the product QuickSpecs on the Hewlett Packard Enterprise website (http://www.hpe.com/info/qs).
NVDIMM 2D Data Matrix barcode
The 2D Data Matrix barcode is on the right side of the NVDIMM label and can be scanned by a cell phone or other device.
When scanned, the following information from the label can be copied to your cell phone or device:
(P) is the module part number.
(L) is the technical details shown on the label.
(S) is the module serial number.
Example: (P)HMN82GR7AFR4N-VK (L)16GB 1Rx4 NN4-2666V-RZZZ-10(S)80AD-01-1742-11AED5C2
Component identification 21

NVDIMM LED identification

Item LED description LED color
1 Power LED Green
2 Function LED Blue
NVDIMM-N LED combinations
State Definition NVDIMM-N Power LED
0 AC power is on (12V rail) but the NVM
controller is not working or not ready.
1 AC power is on (12V rail) and the NVM
controller is ready.
2 AC power is off or the battery is off (12V
rail off).
3 AC power is on (12V rail) or the battery is
on (12V rail) and the NVDIMM-N is active (backup and restore).
NVDIMM Function LED patterns
For the purpose of this table, the NVDIMM-N LED operates as follows:
Solid indicates that the LED remains in the on state.
Flashing indicates that the LED is on for 2 seconds and off for 1 second.
Fast-flashing indicates that the LED is on for 300 ms and off for 300 ms.
State Definition NVDIMM-N Function LED
NVDIMM-N Function
(green)
On Off
On On
Off Off
On Flashing
LED (blue)
0 The restore operation is in progress. Flashing
1 The restore operation is successful. Solid or On
2 Erase is in progress. Flashing
3 The erase operation is successful. Solid or On
4 The NVDIMM-N is armed, and the NVDIMM-N is in
normal operation.
22 Component identification
Solid or On
Table Continued
State Definition NVDIMM-N Function LED
5 The save operation is in progress. Flashing
6 The NVDIMM-N finished saving and battery is still
turned on (12 V still powered).
7 The NVDIMM-N has an internal error or a firmware
update is in progress. For more information about an NVDIMM-N internal error, see the IML.

HPE Persistent Memory module label identification

Solid or On
Fast-flashing
Item Description Example
1 Unique ID number 8089-A2-1802-1234567
2 Model number NMA1XBD512G2S
3 Capacity
4 DataMatrix bar code Includes part number and serial number
For more information about product features, specifications, options, configurations, and compatibility, see the product QuickSpecs on the Hewlett Packard Enterprise website (http://www.hpe.com/support/
persistentmemoryQS).

Device numbers

8 SFF device bay numbering
128 GB
256 GB
512 GB
Component identification 23
8 SFF + 2 SFF device bay numbering
Item Description
1 Box 1, bays 1-8
2 Box 2, bays 1 and 2
4 LFF device bay numbering
10 SFF NVMe/SAS backplane option device bay numbering
When the 10 SFF NVMe/SAS backplane option is installed, NVMe drives must be installed in bays 9 and
10.The other bays support a mix of NVMe and SAS drives.
Optional rear device bay numbering
The optional rear device bay supports either 1 SFF drive in a SmartDrive carrier, or 2 uFF M.2 drives in an HPE Smart Carrier M.2 (SCM).
When the HPE SFF Flash Adapter is installed, the uFF drives are recognized as 1 and 101.
24 Component identification

Hot-plug drive LED definitions

Item LED Status Definition
1 Locate Solid blue The drive is being identified by a host
Flashing blue The drive carrier firmware is being updated or
2 Activity ring Rotating green Drive activity.
Off No drive activity.
3 Do not remove Solid white Do not remove the drive. Removing the drive
application.
requires an update.
causes one or more of the logical drives to fail.
Off Removing the drive does not cause a logical
drive to fail.
4 Drive status Solid green The drive is a member of one or more logical
drives.
Flashing green
Flashing amber/
green
Flashing amber The drive is not configured and predicts the
Solid amber The drive has failed.
The drive is doing one of the following:
Rebuilding
Performing a RAID migration
Performing a strip size migration
Performing a capacity expansion
Performing a logical drive extension
Erasing
Spare part activation
The drive is a member of one or more logical drives and predicts the drive will fail.
drive will fail.
Off The drive is not configured by a RAID
controller or a spare drive.
Component identification 25

NVMe SSD LED definitions

The NVMe SSD is a PCIe bus device. A device attached to a PCIe bus cannot be removed without allowing the device and bus to complete and cease the signal/traffic flow.
CAUTION: Do not remove an NVMe SSD from the drive bay while the Do not remove LED is flashing. The Do not remove LED flashes to indicate that the device is still in use. Removing the NVMe SSD before the device has completed and ceased signal/traffic flow can cause loss of data.
Item LED Status Definition
1 Locate Solid blue The drive is being identified by a host application.
Flashing blue The drive carrier firmware is being updated or requires an update.
2 Activity
ring
Off No drive activity
3 Drive
status
Flashing green
Flashing amber/
Flashing amber The drive is not configured and predicts the drive will fail.
Solid amber The drive has failed.
Rotating green Drive activity
Solid green The drive is a member of one or more logical drives.
The drive is doing one of the following:
Rebuilding
Performing a RAID migration
Performing a stripe size migration
Performing a capacity expansion
Performing a logical drive extension
Erasing
The drive is a member of one or more logical drives and predicts the
green
drive will fail.
Off The drive is not configured by a RAID controller.
4 Do not
remove
26 Component identification
Solid white Do not remove the drive. The drive must be ejected from the PCIe bus
prior to removal.
Table Continued
Item LED Status Definition
Flashing white The drive ejection request is pending.
Off The drive has been ejected.
5 Power Solid green Do not remove the drive. The drive must be ejected from the PCIe bus
prior to removal.
Flashing green The drive ejection request is pending.
Off The drive has been ejected.

uFF drive components and LEDs

Item Description Status
1 Locate Off—Normal
Solid blue—The drive is being identified by a host application
Flashing blue—The drive firmware is being updated or requires an update
2 uFF drive ejection latch Removes the uFF drive when released
3 Do not remove LED Off—OK to remove the drive. Removing the drive
does not cause a logical drive to fail.
Solid white—Do not remove the drive. Removing the drive causes one or more of the logical drives to fail.
Table Continued
Component identification 27
Item Description Status
4 Drive status LED • Off—The drive is not configured by a RAID
controller
Solid green—The drive is a member of one or more logical drives
Flashing green (4 Hz)—The drive is operating normally and has activity
Flashing green (1 Hz)—The drive is rebuilding or performing a RAID migration, stripe size migration, capacity expansion, logical drive extension, or is erasing
Flashing amber/green (1 Hz)—The drive is a member of one or more logical drives that predicts the drive will fail
Solid amber—The drive has failed
Flashing amber (1 Hz)—The drive is not configured and predicts the drive will fail
5 Adapter ejection release latch
and handle

Hot-plug fans

CAUTION: To avoid damage to server components, fan blanks must be installed in fan bays 1 and
2 in a single-processor configuration.
CAUTION: To avoid damage to the equipment, do not operate the server for extended periods of time if the server does not have the optimal number of fans installed. Although the server might boot, Hewlett Packard Enterprise does not recommend operating the server without the required fans installed and operating.
The valid fan configurations are listed in the following tables.
One-processor configuration
Fan bay 1 Fan bay 2 Fan bay 3 Fan bay 4 Fan bay 5 Fan bay 6 Fan bay 7
Fan blank Fan blank Fan Fan Fan Fan Fan
Two-processor configuration
Fan bay 1 Fan bay 2 Fan bay 3 Fan bay 4 Fan bay 5 Fan bay 6 Fan bay 7
Removes the SFF flash adapter when released
Fan Fan Fan Fan Fan Fan Fan
28 Component identification
The loss of a single fan rotor (one standard fan) causes loss of redundancy. The loss of two fan rotors (two standard fans or one high-performance fan) causes the server to initiate a shutdown.
The high-performance fans are used for 8 SFF +2 SFF NVMe and 10 SFF drive configurations when NVMe drives are installed in the server. They are also required for ASHRAE-compliant configurations. For more information on ASHRAE-compliant configurations, see the Hewlett Packard Enterprise website http://www.hpe.com/servers/ASHRAE.
The server supports variable fan speeds. The fans operate at minimum speed until a temperature change requires a fan speed increase to cool the server. The server shuts down during the following temperature­related scenarios:
At POST and in the OS, iLO performs an orderly shutdown if a cautionary temperature level is detected. If the server hardware detects a critical temperature level before an orderly shutdown occurs, the server performs an immediate shutdown.
When the Thermal Shutdown feature is disabled in the BIOS/Platform Configuration (RBSU), iLO does not perform an orderly shutdown when a cautionary temperature level is detected. Disabling this feature does not disable the server hardware from performing an immediate shutdown when a critical temperature level is detected.
CAUTION: A thermal event can damage server components when the Thermal Shutdown feature is disabled in the BIOS/Platform Configuration (RBSU).
Component identification 29

HPE Smart Array P824i-p MR Gen10 Controller

Components
Item Description
1 Internal SAS port 1i
2 Internal SAS port 2i
3 Internal SAS port 3i
4 Internal SAS port 4i
5 Controller backup power cable connector
6 Internal SAS port 5i
7 Internal SAS port 6i
30 Component identification
Loading...
+ 154 hidden pages